Jump to content

How can I reattach the hairspring to the stud?

scholzie
 Share

Recommended Posts

scholzie New Member

scholzie

Posted
Posted (edited)

While disassembling a Unitas 6497 (or during subsequent reassembly) I slightly deformed the hairspring, and to fix it I removed the wheel from the balance cock and then the hairspring from the wheel. The balance cock is of the Etachron type, so the index pin is simply clipped into the stud support. The spring sits inside a notch on the underside of the pin, and is secured in place with some sort of gummy, flexible adhesive (instead of a tiny pin, as I've seen elsewhere).

Anyway, I had a lot of trouble getting the spring stud back into the stud support, and after about an hour of man-handling the glue finally gave out and the spring came loose. Now I have a spring (in perfect condition, thank you very much!) and stud I need to reattach to each other.

What kind of adhesive is this? What are some accepted ways of reattaching the spring? I saw someone on the internet use shellac, but 1) I don't think that was the correct thing to do (this stuff was flexible, and probably for a reason) and 2) I don't have shellac or know how to use it regardless.

Thanks for reading, and thanks for any help you can offer!

Here are some pictures to help visualize what I'm talking about:

IMG_5434.thumb.jpg.656c6d05c568ddd68651c7c30d5ab815.jpg

IMG_5436.thumb.jpg.130688aa87342ba5b35dbf1b4d7a2903.jpg

Edited by scholzie
Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
Posted

This is not a fitting that uses pins. The hairspring is held in place by that greenish stuff in the slot. I would clean out that greenish stuff first, I think a tiny drop of Loctite should do the trick as this is commonly used to bond metal so there shouldn't be any problem in it affecting the hairspring.

 

  • Like 1
Link to comment
Share on other sites
Mark Distinguished Member

Mark

Posted
Posted
10 hours ago, clockboy said:

Can to attach with a normal hairspring pin. If so it's much easier than messing with glue. 

 

https://www.cousinsuk.com/product/hairspring-collets-pins-pocket-watch

This particular one is not possible to pin unfortunately. The best remedy is to clean out the old adhesive and apply new. I would use a slower drying epoxy (very very small amount applied using a clock oiler for example). Apply when the glue is tacky enough to hold the spring in place so you can test if it is correctly positioned. Once you are convinced of its correct position along the length of the end of the spring then leave it to set.

Do this with the stud re-attached to the index but the hairspring not attached to the balance staff so that you can check the position of the hairspring collet being directly over the pivot hole. This will make it easier for you to observe that the spring is straight and true on the stud.

  • Like 6
  • Thanks 1
Link to comment
Share on other sites
scholzie New Member

scholzie

Posted
  • Author
Posted
This particular one is not possible to pin unfortunately. The best remedy is to clean out the old adhesive and apply new. I would use a slower drying epoxy (very very small amount applied using a clock oiler for example). Apply when the glue is tacky enough to hold the spring in place so you can test if it is correctly positioned. Once you are convinced of its correct position along the length of the end of the spring then leave it to set.
Do this with the stud re-attached to the index but the hairspring not attached to the balance staff so that you can check the position of the hairspring collet being directly over the pivot hole. This will make it easier for you to observe that the spring is straight and true on the stud.

Thank you Mark! Any particular brand or type of epoxy you'd suggest, or can I use any slow drying epoxy made for metals?


Sent from my iPhone using Tapatalk
Link to comment
Share on other sites
scholzie New Member

scholzie

Posted
  • Author
Posted

Hot glue probably would have worked a charm, actually. I used a Devcon epoxy with 60m working time, applied with the tip of a sharpened x-acto blade. I don't have spare oilers like all you old timers :P. I'm brand new to this hobby so I don't have spares of anything!

 

The epoxy seems to have worked fine. And by some grace of His Noodly Appendage, the hairspring collet sits nearly perfectly centered over the pivot hole on the balance cock even after all it's been through.

 

I'm going to remove it one last time, give it a rinse in naphtha and denatured alcohol, and put it all back together.

 

 

Sent from my iPhone using Tapatalk

 

Link to comment
Share on other sites
  • 1 year later...
Colditz WRT Addict

Colditz

Posted
Posted

just wanted to thank you guys for this post. I have exactly the same problem on a Seiko movement. I think  the cleaning fluid removed / degraded the fixing. I now have to reposition the hair spring to the stud. What is your opinion on using superglue? I think I will use Devcon epoxy 60 min.

Link to comment
Share on other sites
Nucejoe Distinguished Member

Nucejoe

Posted
Posted

 I wouldn,t glue anything unassembled. Since as the glue dries out, you are facing a set  HS- STUD  position which may render the HS unlevel, coned .. once assembled.

So, once I position the collet right over the jewel hole and regulator pin along the lenght of HS end checks alright. I assemble the HS on the wheel ,run HS through slots in regulator and stud and install on mainplate with the cock screwed tight.  Everything positioned right as should be . I will then place the mainplate on a level surface. cock facing down, Stud slot facing up. What I see is what I get if I glue at this time, since the glue dries out holding the HS at this position where we know the pivots ( final position ) are inside the jewel hole and approved the configuration and levelness of HS etc before applying the glue.

To apply the glue, put only as much as you need(  to fill the slud slot)on flat face of your screwdrive tip, lumped as wide as the stud slot. No more, excess glue runs and ends up where not welcomed. The stud slot was faced up, if faced down even small amount of glue  can drip out of the slot and end up on BW.  The next day you find everything exactly as you approved,  I remove the cock-Hs  rinse ready for assembly. 

Should there be a need, I removed  and soak the Stud-HS section in acetone or burn the glue by heat with soldering gun.

Regards

 

  • Thanks 1
Link to comment
Share on other sites
Colditz WRT Addict

Colditz

Posted
Posted

Thanks Nucejoe.

I think I will follow your advice. I'd rather have the balance in position and stable on the plate than floating around. I will let you know how it goes and I will try and take pictures or a short video.

Can I upload a video to here?

 

Link to comment
Share on other sites
Nucejoe Distinguished Member

Nucejoe

Posted
Posted

Hi colditz,

As long as you pick small amount of gule and on one side of screwdriver only ( avoid having glue on both sides of the blade) and ofcourse not runny glue, you are likely to get near perfect results.

Facts are, we don,t have a full top view of HS when installed even less in motion, even if we did, manipualtion is limited to external section of HS. All is most reachable when outside. So why risk damaging the perfecrion we worked for, glue the perfection in. No need to spend hours, days to master installed HS manipulation.

Furthuremore I shim the external circumference of bridge to lower the bridge jewel, so it keeps the balance wheel from turning as turning  may let the HS to slip out of glue before it dries.

Regards

  • Like 2
Link to comment
Share on other sites
Nucejoe Distinguished Member

Nucejoe

Posted
Posted
9 hours ago, Colditz said:

Thanks Nucejoe.

I think I will follow your advice. I'd rather have the balance in position and stable on the plate than floating around. I will let you know how it goes and I will try and take pictures or a short video.

Can I upload a video to here?

 

I think you can upload, see others done.

  • Like 1
Link to comment
Share on other sites
nichod WRT Addict

nichod

Posted
Posted
45 minutes ago, Colditz said:

What is denatured alcohol?

 

I suspect that is only available in the U.S.A.   They change the nature of ethanol into a poison substance so we cannot drink it and cheat our rulers out of their proper taxes!

Link to comment
Share on other sites
Nucejoe Distinguished Member

Nucejoe

Posted
Posted
42 minutes ago, Colditz said:

Hi Nucejo

I have purchased a new digital microscope so we will see what is can do. Cheers

Hi, I shim the cock outbound ( pig,s ear with a piece of aluminum foil) to temoprarily lower the cock jewel so to prevent the wheel from turning. And mix the epoxy( not runny) after all is set up, smother the expoxy( using a safety razor) on a flat surface( piece of cardboard or glass etc) thin like .25 mm or less, all this just to have good control over the amount of epoxy you pick up,  avoid picking excess epoxy ( so if your hand moves/ shakes no expoxy would be on the sides of the blade to get on other parts. Apply the glue and leave stud slot face up. You should have some acetone ready, to immediately  rinse if any part get messed up with epoxy. Some epoxy may inevitably ran down the slot, which can later be scraped off.

You should expect perfect results. No hard task for a horologist.

Regards

  • Like 1
Link to comment
Share on other sites
 Share
Go to topic listing


  • Similar Content

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Neverenoughwatches
      Without Our Forum

      By Neverenoughwatches · Posted

      I dont understand why a patreon membership would have limited places ??
    • clockboy
      Hi all

      By clockboy · Posted

      Welcome to the forum, enjoy. It’s highly unlikely you will be able to purchase a new bezel look on eBay for a pulsar watch for repair to find a bezel.
    • JohnR725
      Balance spring fell out of regulator pin.

      By JohnR725 · Posted

      just one little minor reminder here this isn't your normal balance wheel.  pages 17 and 18 are what you really want to be looking at. normally studs don't turn but this watch has the etachron system designed for lots of adjustment. Personally I would try to rotate the stud back to where it's supposed to be. If you're lucky you didn't actually bend it at the stud it just looks really bad as the stud has been rotated grossly out of position.. I think things will look a lot better if you put the hairspring back where it's supposed to be by rotating the stud. it's hard to tell if you actually did bend it at the stud or not we won't know until you rotate the stud back more or less where it's supposed to be. Then you want to pay attention to the manual of how to put the hairspring back in the regulator pins because yes they rotate also and they rotated specific directions otherwise bad things will happen to your hairspring. so initially you can open up the regulator as wide as it can go and don't worry about closing it until thing everything is right then you can close them a little bit
    • oldhippy
      Is this a 'hack' ?

      By oldhippy · Posted

      I need to see photos of the whole movement before I comment. 
    • swiss2k
      Omega cal. 565 - low amplitude

      By swiss2k · Posted

      Hi @Jon, so, from one extreme to another the beat error is 0.1(min.pos) to 0.2(msx.pos), and as you mentioned the rate does up and down dramatically. Also checked the position of the collet, and the collet is not central to the jewel on the balance cock. Balance moves freely, per my understanding.   So, after 24h the ampl. fell down by approx 20 deg, which I would assume is expected. After adjusting the endshake I believe I gained around +10 deg. of balance movement. Which is great, and overall the balance is not at 220'ish deg.   What I did next, some might think is non-orthodox, but was wort a try. I too the mainspring out, checked again for endshake and if the pin moves freely, and cleaned everything. Usually when installing the mainspring I would use some barrel grease on the barrel walls, install the spring and put a 2-3 drops of D-5 oil on top of the wounded spring and in the places where the arbor sits. This time I took the spring and applied a ultra this coat of Molykote Dx paste on the whole spring, before installing it in to the barrel, and added some oil to the arbor as usual.  The result improved, at a full wound the balance produces about 230-237 deg. @JohnR725 I'm getting closer to 300 😃   What I am noticing, there is a fluctuation in amplitude. With time it would rise and drop about total 8-10 deg in an interval about 2 minutes. I assumed this ruled out the power transfer from the barrel itself. So I took the gear train out, cleaned and lubed. 
×
×
  • Create New...