Jump to content

My new workspace.

dman2112

By dman2112
in Tools & Equipment

 Share

Recommended Posts

dman2112 Watch Enthusiast

dman2112

Posted
Posted

Well after a year of building my skills and discovering good tools vs bad, I finally have a workspace that is comfortable and large enough to lay out all of my tools properly. A lot of advice I gleaned from Mark and this board so thanks to all865c775d316aac685e84ba7543181d62.jpg
 
be62be3d50cf7ab643ce9fff49a2862a.jpg

8ff36f25a54c4fde67555daf36c49e3f.jpg
 
 
Sent from my iPhone using Tapatalk

  • Like 8
Link to comment
Share on other sites
dman2112 Watch Enthusiast

dman2112

Posted
  • Author
Posted

Its a 3.5X - 45X.  It works just great.  It has an 8" working distance and I use it for balance work and inspecting the mainplate and bridge jewels after cleaning.  You can actually see through a cap jewel into the setting if the ultrasonic removed all the old oil (oil bubble) if there was one.  

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Randy55
      Introduction

      By Randy55 · Posted

      Welcome to the group Stirky. You can search for just about every subject in the craft here. Don't be afraid to ask if you can't find the answer that may have already been covered ( some ad nauseum LOL ). You don't have to buy Bergeon to get good quality. There are many decent mid-range tools available that will last you a lifetime. Cousins would be a good place to start . Cheers from across the pond ! Randy
    • Jon
      What are these Seitz B-Jewels?

      By Jon · Posted

      I picked up a similar amount of these jewels some years ago in a watch and clock fair. Every now and then they come in handy. This week I've got a rubbed in bombe jewel in the balance cock that is cracked and needs replacing. Very handy to have a vintage assortment of these type of jewels!
    • Stirky
      Diagram for 6497 motion works

      By Stirky · Posted

      Thanks Jon.
    • Jon
      Diagram for 6497 motion works

      By Jon · Posted

      Great diagram with the teeth and pinion count. Simple way to reduce the speed of the hour wheel by the 12:1 minute wheel. Genius and yet so simple. Always good to reinforce the principal by what you have done in your drawing. Keep doing that. I had a drawing on my wall for years showing me this which is very similar to the drawing you have done. Here's a formula to work out the beats per hour of a watch movement. The movement's BPH is dictated by the wheel teeth and pinion count and the hairspring being vibrated to the correct BPH by finding the pinning up point on the hairspring using a vibrating tool.  The reason in the formula there is X2 on the top line is because there are two pallet stones.
    • DDean
      Incabloc Lyre Spring & Low Earth Orbit

      By DDean · Posted

      So I just wanted to say "thank you" again.  The angle is the key bit it seems and yes, it did basically just fall, or float, back into position when I got it lined up just right. I had meant to add that now that I see how it goes in, I totally see how it came out in the first place, and that whomever cloned the original movement didn't pay much attention to the fine details around the setting or how it interfaces with the balance cock or the "rings" on the regulator and/or stud carrier arms.
×
×
  • Create New...