Jump to content

Today’s Competition 3


oldhippy

Recommended Posts

When it comes to Longcase Clocks or Grandfather clocks as they are known it can be a minefield knowing what is correct. We have 4 dials here so can you give the correct range of dates when they would have appeared.  

1.jpg

23.jpg

2.jpg

24.jpg

Edited by oldhippy
Link to comment
Share on other sites

Your best yet oldhippy. Found it difficult because not just the dials are indicators of the date (I think)

However heres my shot:

1) 1775-1780
2) 1810-1820
3) 1790-1830 (Thomas Dickinson)
4) 1810-1812

How you dated them will be of interest to me for sure.

Link to comment
Share on other sites

This is what I think they are,

1, A  clock dial with 5 minute divisions and roman hour numerals and simple corner decoration made between 1770 and 1800.

2 and 3, 1800-1830 with 3 probably being the eairlier of the two shown as it still retains the 5 minute markings

4, 1830 onwards to about 1870 the more paint the later the dial as a rough rule of thumb.

Link to comment
Share on other sites

wis1971 is the winner. You sure know your Longcase dials or do you have a good book.:D

Here is the correct info. I put two dials in with the same date but that did not fool you. Dials are put into periods of date. What you might come across is a clock outside of the dates this is down to places away from what is in with the dial makes and their stock might be a bit behind the times to what is being produced in the cities, this happens a lot the further north you go, then you have to look at the case. A quick tip with the case is the door, long slender doors are early short wide doors are very late.

 

Period one dials date from about 1770 to about 1800 and look more or less like this:

Picture 1, The hour numerals are in Roman lettering (FROM I to XII) and the minute numerals are in arabic (5 to 60) numbered every five minutes (often called five minute numbering).

Period one dials date from about 1770 to about 1800 and look more or less like this:

The hour numerals are in Roman lettering (FROM I to XII) and the minute numerals are in arabic (5 to 60) numbered every five minutes (often called five minute numbering).

 

Picture 2 and 3,

Period two dials change in three distinct ways.

Whereas period one corner decoration tends to be simple gold scrollwork or little flowers, fruit or the occasional bird, period two dials tend to have either geometric shapes, or shells, or abstract patterns – usually with a little more colour than period one.

Period two dials start to lose the five minute numbering and this is replaced with fifteen minute numbering (15,30,45,60) possibly in slightly smaller size, around the hour numbers.

The Hour numerals are often in arabic rather than roman style.

Period two tends to cover the period 1800 to 1825-30

Picture 4

Period three dials are from 1830 onwards until the demise of longcase clockmaking about 1850-70.

The minute numbering has disappeared completely and the hour numerals are back as Roman numerals, (I, II, III, IIII, V, VI, etc..)

The corner decoration tends to be full colour scenes, often of country scenes, sometimes of the four seasons, countries (England, Scotland, Ireland, Wales) or the four continents.

Sometimes there are specific corner or arch paintings to do with trade or commerce or perhaps with a religious or masonic theme.

Thanks to all that took part and to those for looking. In my time I must have restored hundreds of these clocks from 30hour 8day and month duration, Many extremely early.  

  • Like 2
Link to comment
Share on other sites

I know of this one. The thing with hands they get broken and they can be replaced which is not that difficult. They have a story in themselves as old ones will be thick and its easy to pick out the hand made from the mass produced, but handmade Longcase clock hands can be obtained today. 

Link to comment
Share on other sites

Well I guess the correct order of age half correct, got the first two correct, but got the last two around the wrong way, but I was going by hand styles from De Carles watch and clock encyclopaedia. Thanks for the information on the dials as I definately learnt something here.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Hello everyone, for what it's worth, here is my approach: 1. Escape wheel submerged in Epilame, then dried quickly with a hairdryer. Then the final tip of the pivots are cleaned by poking into pithwood. The logic being that the Epilame is removed at the intended contact point (to avoid any residue that may mix with the oil), but remains in the areas where oil is not supposed to spread to (further down the pivot towards the wheel). The escape wheel teeth also benefit from having Epilame to keep the 9415 in place.  2. I use a syringe to treat only the pallet stones. I suspend the pallet fork with some Rodico so that the stones hang downwards. I notably use a rather thick needle where a drop WON'T form, but rather where the Epilame liquid stays in the needle tip, which I then dip into the pallet stones. It requires some practice to get the right amount of Epilame into the needle tip, but it works for me now. This way, no drop will "jump" onto the pallet fork and potentially go all the way to the pivots.  3. I let the movement run for a few minutes without lubricating the pallet stones... to scrape off the Epilame in the intended contact "channel". Then I remove the balance again and lubricate the exit pallet stone with 3-4 successive drops. See the "channel" that forms on the pallet stone in the picture -- not so easy to see, but it's visible.   I am conflicted about the use of Epliame in balance jewel settings. My impression is that the two jewels sufficiently suspend the oil (even 9010). Apparently Rolex recommends NOT to use Epliame there (heard from a former Rolex service center watchmaker), as it could cause additional wear. Apart from that, I follow specific instructions where I can find them. E.g. the infamous Rolex reverser wheels or sometimes (parts of) the seconds wheel. Exception: I'm currently servicing an Eta 2824 and will probably ignore the service sheet that recommends treating the whole keyless works with Epilame and then using HP1300... I'll skip the Epilame and use 9504 grease.        
    • I'm going to give this a try today/tomorrow on my UTC33/Seiko 66, thanks!
    • Hello and welcome from Leeds, England. 
    • Don't forget Mark is a hard working watch maker so he is also tied up with work. I'm sure he is keeping his eye on this forum making sure it is running along nicely. 
    • Thank you for your introduction and welcome to this friendly forum. We all look forward to your contributions and continued involvement.    
×
×
  • Create New...