Jump to content

How do you reduce a plastic crystal diameter easily?

chriz74

By chriz74
in Watch Repairs Help & Advice

 Share

Recommended Posts

chriz74 WRT Addict

chriz74

Posted
Posted

I had to reduce the diameter of a sternkreuz glass from 30.3mm to 30mm or the retainer ring of the watch wouldn't fit. To do so I used sandpaper by hand (very tiring and time consuming) and for the final part I used the dremel with a sanding tip. Then I used the dremel and polywatch to polish.

Do you use a lathe to do this kind of job?

I thought if I could put the glass on the dremel maybe with a sucker then the process would be a lot faster and easier. I have another one that I want to try but by hand is too long.

advices?

Link to comment
Share on other sites
dman2112 Watch Enthusiast

dman2112

Posted
Posted
Did you do anything to solve?

Nothing tried yet. But I was going to use a lathe chuck to hold the crystal and chuck it in a variable speed drill and spin it while holding a sanding stick to the edge. Have not validated the theory yet so can't recommend


Sent from my iPhone using Tapatalk
Link to comment
Share on other sites
ricardopalamino Distinguished Member

ricardopalamino

Posted
Posted

You can order a 3 or 3.1 crystal ,...or as you suggested , try to use a sucker in a drill or dremel . I had a similar situation where I wanted to turn a case back to put a finish on it and I got a small sucker from ebay that is used to prop a cell phone for viewing . I also went to the hardware store and Wal-mart and looked at the clear plastic suckers that are used on bathroom and kitchen racks .

Link to comment
Share on other sites
ricardopalamino Distinguished Member

ricardopalamino

Posted
Posted
7 hours ago, chriz74 said:

How did you attach the sucker to a dremel head?

Well , for mine ,  the sucker head to prop a smart phone had a wooden dowel that I attached to a drill . But the ones for bathroom racks have small gauge wire for the racks that can be cut and installed in a larger dremel collet....I think.

Link to comment
Share on other sites
Hamish Member

Hamish

Posted
Posted

Hi,

You might have it all sorted by now, but I have used this successfuly in the past. This is if you have a lathe.

(Hope that link copied over)

You do have to fiddle a bit to get the crystal central, but if you keep the speed slow it is not crucial. The other tip is to use the file across the work and not aligned with it. I learnt the hard way that crystals will be easily scratched if the file slips off the work. The plus side is that the crystal remains circular and you dont seem to compromise its fit as I think you would do with a dremel of sandpaper. The suction cup seems simple and a good idea too.

Link to comment
Share on other sites
  • 3 weeks later...
dman2112 Watch Enthusiast

dman2112

Posted
Posted

Update. I discovered an easy way. I just polish the outer diameter on my buffer that I use for case polishing. Very gentle and worked like a champ. I just spin the crystal around as I go and it remained perfectly concentric. I just kept checking with a caliper.


Sent from my iPhone using Tapatalk

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Knebo
      Epilame / Fixodrop

      By Knebo · Posted

      Hello everyone, for what it's worth, here is my approach: 1. Escape wheel submerged in Epilame, then dried quickly with a hairdryer. Then the final tip of the pivots are cleaned by poking into pithwood. The logic being that the Epilame is removed at the intended contact point (to avoid any residue that may mix with the oil), but remains in the areas where oil is not supposed to spread to (further down the pivot towards the wheel). The escape wheel teeth also benefit from having Epilame to keep the 9415 in place.  2. I use a syringe to treat only the pallet stones. I suspend the pallet fork with some Rodico so that the stones hang downwards. I notably use a rather thick needle where a drop WON'T form, but rather where the Epilame liquid stays in the needle tip, which I then dip into the pallet stones. It requires some practice to get the right amount of Epilame into the needle tip, but it works for me now. This way, no drop will "jump" onto the pallet fork and potentially go all the way to the pivots.  3. I let the movement run for a few minutes without lubricating the pallet stones... to scrape off the Epilame in the intended contact "channel". Then I remove the balance again and lubricate the exit pallet stone with 3-4 successive drops. See the "channel" that forms on the pallet stone in the picture -- not so easy to see, but it's visible.   I am conflicted about the use of Epliame in balance jewel settings. My impression is that the two jewels sufficiently suspend the oil (even 9010). Apparently Rolex recommends NOT to use Epliame there (heard from a former Rolex service center watchmaker), as it could cause additional wear. Apart from that, I follow specific instructions where I can find them. E.g. the infamous Rolex reverser wheels or sometimes (parts of) the seconds wheel. Exception: I'm currently servicing an Eta 2824 and will probably ignore the service sheet that recommends treating the whole keyless works with Epilame and then using HP1300... I'll skip the Epilame and use 9504 grease.        
    • GuyMontag
      Movement holder made with 3D printer

      By GuyMontag · Posted

      I'm going to give this a try today/tomorrow on my UTC33/Seiko 66, thanks!
    • RichardHarris123
      Intro

      By RichardHarris123 · Posted

      Hello and welcome from Leeds, England. 
    • oldhippy
      Without Our Forum

      By oldhippy · Posted

      Don't forget Mark is a hard working watch maker so he is also tied up with work. I'm sure he is keeping his eye on this forum making sure it is running along nicely. 
    • oldhippy
      Intro

      By oldhippy · Posted

      Thank you for your introduction and welcome to this friendly forum. We all look forward to your contributions and continued involvement.    
×
×
  • Create New...