Jump to content

How do you reduce a plastic crystal diameter easily?

chriz74

By chriz74
in Watch Repairs Help & Advice

 Share

Recommended Posts

chriz74 WRT Addict

chriz74

Posted
Posted

I had to reduce the diameter of a sternkreuz glass from 30.3mm to 30mm or the retainer ring of the watch wouldn't fit. To do so I used sandpaper by hand (very tiring and time consuming) and for the final part I used the dremel with a sanding tip. Then I used the dremel and polywatch to polish.

Do you use a lathe to do this kind of job?

I thought if I could put the glass on the dremel maybe with a sucker then the process would be a lot faster and easier. I have another one that I want to try but by hand is too long.

advices?

Link to comment
Share on other sites
dman2112 Watch Enthusiast

dman2112

Posted
Posted
Did you do anything to solve?

Nothing tried yet. But I was going to use a lathe chuck to hold the crystal and chuck it in a variable speed drill and spin it while holding a sanding stick to the edge. Have not validated the theory yet so can't recommend


Sent from my iPhone using Tapatalk
Link to comment
Share on other sites
ricardopalamino Distinguished Member

ricardopalamino

Posted
Posted

You can order a 3 or 3.1 crystal ,...or as you suggested , try to use a sucker in a drill or dremel . I had a similar situation where I wanted to turn a case back to put a finish on it and I got a small sucker from ebay that is used to prop a cell phone for viewing . I also went to the hardware store and Wal-mart and looked at the clear plastic suckers that are used on bathroom and kitchen racks .

Link to comment
Share on other sites
ricardopalamino Distinguished Member

ricardopalamino

Posted
Posted
7 hours ago, chriz74 said:

How did you attach the sucker to a dremel head?

Well , for mine ,  the sucker head to prop a smart phone had a wooden dowel that I attached to a drill . But the ones for bathroom racks have small gauge wire for the racks that can be cut and installed in a larger dremel collet....I think.

Link to comment
Share on other sites
Hamish Member

Hamish

Posted
Posted

Hi,

You might have it all sorted by now, but I have used this successfuly in the past. This is if you have a lathe.

(Hope that link copied over)

You do have to fiddle a bit to get the crystal central, but if you keep the speed slow it is not crucial. The other tip is to use the file across the work and not aligned with it. I learnt the hard way that crystals will be easily scratched if the file slips off the work. The plus side is that the crystal remains circular and you dont seem to compromise its fit as I think you would do with a dremel of sandpaper. The suction cup seems simple and a good idea too.

Link to comment
Share on other sites
  • 3 weeks later...
dman2112 Watch Enthusiast

dman2112

Posted
Posted

Update. I discovered an easy way. I just polish the outer diameter on my buffer that I use for case polishing. Very gentle and worked like a champ. I just spin the crystal around as I go and it remained perfectly concentric. I just kept checking with a caliper.


Sent from my iPhone using Tapatalk

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Hawaiikook808
      Balance spring fell out of regulator pin.

      By Hawaiikook808 · Posted

      Thank you so much, Hector and CJ. I appreciate the tech sheet and the video. Gasp, I think I will make the attempt. What's the worst that can happen? I think there may be a new balance complete in my future, though.  I'll update the post and let you know the result. R, Frank  
    • Waggy
      Movement holder made with 3D printer

      By Waggy · Posted

      So here is the new base (v 2.1), I made it so that the base will fit over and swallow the stump of the hand pusher tool (or at least my clone of the tool), I also reduced the OD of the bottom skirt a little as it looked/felt a little large, here are a few pictures and the fake .pdf file which you need to convert to .zip once downloaded.   The cut-out seen on the below image on the bottom of the base should swallow the OD (40 mm, +0.1 mm tolerance) of the stump and the height of the stump 9.5mm (measured to 9.1mm, but rounded to 9.5mm) - let me know if this works for your tool.   Note, I think you may need to print supports for the new internal shelf created? Here is the fake .pdf for just the FreeCAD base file and 3mf files Modular Movement Holder.pdf Here is the fake pdf for complete set of the new base and ring FreeCAD/3mf files: Modular Movement Holder base and ring v 2.1.pdf However, I'm wondering how often you could use this feature, adding the dial usually increases the OD of the movement, so you would need a new (larger) adapter ring tuned to the OD of the dial and I wouldn't like to grip the dial in any kind of movement holder if It could be avoided for fear of damaging it. Maybe I'm misunderstanding you?
    • HectorLooi
      Balance spring fell out of regulator pin.

      By HectorLooi · Posted

      Hi Frank, you have dived headlong into the deep end. Hairspring work has to be the scariest thing a newbie has to tackle. Your hairspring appears to be bent and just putting it back into the regulator would not allow the balance to work properly. It might start oscillating but the performance would not be good. The proper thing to do is to unstud the hairspring, remove the hairspring from the balance, reinstall the hairspring on the stud carrier, reshape the endcurve and centre the collet to the balance jewel hole. This challenge would either make you or break you. Hope that you will be able to fix your watch. Welcome to the world of watchmaking.  Watch this video. It think it'll give you an idea of the task ahead. From your 1st photo, I think you have a etachron type stud. Let me see if I can find a video on how to remove it from the arm.
    • Curare
      Balance spring fell out of regulator pin.

      By Curare · Posted

      Have read of the Tech Sheet attached on the balance section page 12. It may be bent but until you reposition it back in the regulator pins you'll never know. Cheers CJ 4R35B_4R36A.pdf
    • Hawaiikook808
      Balance spring fell out of regulator pin.

      By Hawaiikook808 · Posted

      Aloha All, My Seiko 4R35B movement stopped working today. Upon closer inspection, it looks like the balance spring came out of the regulator pin. This is my first time working on a balance. Any advice on how to get this spring repositioned (back to normal)? I'm pretty sure that while adjusting the beat error on this movement, I must have turned the stud (I didn't even know they turned), and the spring eventually fell out.  Will the spring go back to even spacing when it's back in the pin, or does it look bent? Thanks, Frank  
×
×
  • Create New...