Jump to content

Guitar and watch repair

jdrichard
 Share

Recommended Posts

jdrichard Distinguished Member

jdrichard

Posted
  • Author
Posted
I was going for reliability over changing the sound. So the Stock USA made Gibson pickups seemed right.  Also I am a drummer but sometimes I have to work out cords so I have a guitars for that.  I wife is a flute player that plays only wooden native craftsman made flutes. So I play her backup sounds. So I have way more drums, cymbals, chimes, rattles, gongs and things that go pop and clack than anything with strings.
As far as using a E string for a spring, it has lots of nickel in it and so I bet it won't temper to spring hard.

As a click spring, a guitar spring should be bent into shape a bit bigger than it needs and then heat and cool : correct?


Sent from my iPhone using Tapatalk Pro
Link to comment
Share on other sites
jdrichard Distinguished Member

jdrichard

Posted
  • Author
Posted
 
This is one of the electric guitars we made. It was made for Jeff Carlisi when he was the guitarist for 38 Special.
 160_DSCF4540.JPG
david

I think this is amazing. Looks like a reverse firebird ?? Where the angled parts are glued the the centre piece of wood in the opposite direction.


Sent from my iPhone using Tapatalk Pro
  • Like 1
Link to comment
Share on other sites
david WRT Addict

david

Posted
Posted

JD,

This was back in the early to mid 1970s. In addition to repair and restoration work we also manufactured steel string acoustic guitars, electric guitars, bluegrass mandolins, bass guitars and a few archtop guitars and banjos. We had a contract with Gibson for their warranty work in the Southeast area.

My first contact with Jay Rhyne was in 1970 as a customer. At that time I was the guitar player in the pit orchestra for the Third US Army Soldier Show. I had a jazz background and could read music so it was a good fit for the Broadway style  of tunes that were done by the show.

While on the road I purchased a 1930s Epiphone (which I still own) from a pawn shop that needed restoration. I took it to Jay but he was always too busy to work on it. At that time he had a three man operation which included himself, Steve Isco, and Grover Jackson. Grover quit and went on to start Jackson Guitars. In any case I went over to Jay's shop and he handed me a box of chisels and showed me what needed to be done. I took the stuff back to my apartment  worked on it and brought it back. Jay then told me that when I was discharged from the Army he would give me a job. For me it was a dream come true. I worked there until the mid 1970s. 

The guy standing up in front of the music stand is me.  The show members did not have to wear uniforms which was fine with me.

GettingItTogether1.jpg

The guy on the left in the picture below is my friend Jim Wilkes . The lady in the middle is Helen Brown and the guy on the right is Ross Clark. Jim became a famous attorney (check Wikipedia for his profile) and Ross Clark became a movie actor and is now known as John Ross Clark.

HelloDolly2.jpg

david

  • Like 1
Link to comment
Share on other sites
jdrichard Distinguished Member

jdrichard

Posted
  • Author
Posted
JD,
This was back in the early to mid 1970s. In addition to repair and restoration work we also manufactured steel string acoustic guitars, electric guitars, bluegrass mandolins, bass guitars and a few archtop guitars and banjos. We had a contract with Gibson for their warranty work in the Southeast area.
My first contact with Jay Rhyne was in 1970 as a customer. At that time I was the guitar player in the pit orchestra for the Third US Army Soldier Show. I had a jazz background and could read music so it was a good fit for the Broadway style  of tunes that were done by the show.
While on the road I purchased a 1930s Epiphone (which I still own) from a pawn shop that needed restoration. I took it to Jay but he was always too busy to work on it. At that time he had a three man operation which included himself, Steve Isco, and Grover Jackson. Grover quit and went on to start Jackson Guitars. In any case I went over to Jay's shop and he handed me a box of chisels and showed me what needed to be done. I took the stuff back to my apartment  worked on it and brought it back. Jay then told me that when I was discharged from the Army he would give me a job. For me it was a dream come true. I worked there until the mid 1970s. 
The guy standing up in front of the music stand is me.  The show members did not have to wear uniforms which was fine with me.
GettingItTogether1.jpg
The guy on the left in the picture below is my friend Jim Wilkes . The lady in the middle is Helen Brown and the guy on the right is Ross Clark. Jim became a famous attorney (check Wikipedia for his profile) and Ross Clark became a movie actor and is now known as John Ross Clark.
HelloDolly2.jpg
david

I know Jackson Guitars and it is quite amazing that you travelled among these talented people. My folks played in their bands starting in 1963 in northern Canada; in clubs run by the Montreal Mafia. I still have my dad's Gresh Tennesseeian from 1965 and in mint condition. I have Repaired a number of amps over the years but the one that brings back the memories is a 1969 Heath Kit. And that is because it was not grounded and would shock my arm as I grabbed the neck and strings. How long did you fix watches for?


Sent from my iPhone using Tapatalk Pro
  • Like 1
Link to comment
Share on other sites
david WRT Addict

david

Posted
Posted

JD,

Even though I have been collecting and restoring small lathes for a number of years,I have only been repairing watches  for a few years. I started by taking the three Time Zone Watch courses. At that time Mark's courses did not exist.  Due to limited time constraints I spend more time studying about watches than actually working on them and currently have no desire to engage in a watch repair business.

I started taking in repair  work a couple of years ago and quickly got burned out replacing batteries, adjusting straps and doing the routine disassemble, replace a broken part, clean, reassemble and adjust. I do enjoy making parts and have geared up my shop to pursue that goal as far as I can. Time permitting I would like to begin making some watches. This goal is a long way off but I am beginning to see some light at the end of the tunnel. I have been putting together equipment to make parts in a precise and repeatable fashion.

Roger Smith and George Daniels started making watches with a jewelers saw, a watchmaker lathe and some files but using this technique it took several years for either of them to produce a single watch. I am going to pursue this using my background which is manufacturing engineering. If I fail at this I can always sell off the equipment at a later date. 

david

Link to comment
Share on other sites
Sleeper Member

Sleeper

Posted
Posted
17 hours ago, jdrichard said:


As a click spring, a guitar spring should be bent into shape a bit bigger than it needs and then heat and cool : correct?


Sent from my iPhone using Tapatalk Pro

nickel steel my not have the right properties for a spring.  Steel is very unique for it elastic and plastic properties.  We put up with rusty springs because low corrosion alloys are not very springy.  Guitar strings have lots of other stuff in them, not just iron and carbon.  

  • Like 1
Link to comment
Share on other sites
jdrichard Distinguished Member

jdrichard

Posted
  • Author
Posted
nickel steel my not have the right properties for a spring.  Steel is very unique for it elastic and plastic properties.  We put up with rusty springs because low corrosion alloys are not very springy.  Guitar strings have lots of other stuff in them, not just iron and carbon.  

So I need to buy some steel wire


Sent from my iPhone using Tapatalk Pro
Link to comment
Share on other sites
Sleeper Member

Sleeper

Posted
Posted
On ‎3‎/‎24‎/‎2017 at 4:49 PM, jdrichard said:


So I need to buy some steel wire


Sent from my iPhone using Tapatalk Pro

I have worked in spring factories here in Texas that made all sorts of springs. It's amazing how they actually do it. Some are cold formed, some are struck, some are wound.  In some ways it's easier than one would think and some ways it's very complex.    

 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • oldhippy
      Movement inserted from crytal side

      By oldhippy · Posted

      Before putting it back in the case I would fit the hands and use a pin vice on the stem to make sure the hands were in line. 
    • Jon
      Introducing myself

      By Jon · Posted

      Hi there  
    • Jon
      Movement inserted from crytal side

      By Jon · Posted

      Put the movement in a movement holder and it will be supported as you push down on the setting lever post to release the winding stem. Make sure the post is over the shoulder of the movement holder so what you are pressing down on is supported. As a general rule, hold the movement and not the movement holder. Replace the hands when the movement isn't in the case and support the centre jewel (if it has one) on a hard surface or staking block when replacing the hands to stop the jewel accidentally moving or even coming out. A dedicated movement holder with a central jewel support is even better, but pricey
    • JohnR725
      Main spring

      By JohnR725 · Posted

      It might help us if we knew which watch like model number.
    • Zedster
      Movement inserted from crytal side

      By Zedster · Posted

      Hi, guys I have a bit of a predicament and hopefully, somebody can advise. I'm working on a Roamer MST 521 where the movement is extracted from the crystal side. I'm now at the final hurdle where I need to replace the movement back into its case but I'm not sure of the correct procedure. I still need to fit the hands but that's where the problem lies. If I insert the winding stem to test the hands for correct alignment I will need to turn the movement over to release the stem again it's the spring-loaded type and needs a small bit of force to push down but with the hands fitted, I don't think I can do this on a cushion without causing some damage to the hands and that's the last thing I want to do, this watch has already been a love-hate relationship and I'm so close to boxing this one off which I'm counting as my first major project.  The other option is to case the movement then fit the hands and hope everything is okay. I've already broken the original winding stem but managed to find a replacement, the last one in stock, so I'm a bit reluctant to keep removing it. Any suggestions would be appreciated. 
×
×
  • Create New...