Jump to content

Watch of Today


mk3

Recommended Posts

11 hours ago, GomBoo said:

  ^

TETO

They Eat Their Own? ? Oh.. to each their own...

image.png.f174a4a10dfd86505bfa1d2f17c83040.png

... well if you think that thing is off the wall, I'm sure I have some much, much odder stuff.

Maybe I should start a separate thread for the most off the wall watches.

  • Like 2
Link to comment
Share on other sites

Just now, AndyHull said:

They Eat Their Own? ? Oh.. to each their own...

image.png.f174a4a10dfd86505bfa1d2f17c83040.png

... well if you think that thing is off the wall, I'm sure I have some much, much odder stuff.

Maybe I should start a separate thread for the most off the wall watches.

I second the motion that you should start an "off the wall watches" thread.

Link to comment
Share on other sites

  • 1 month later...
  • 2 weeks later...

 I really like the 1940's art deco style but it's hard to find a large case. This one is unusual in that it's 28mm. 

It's one of my top 3 & I probably wear it as much as my black strap watch because oxblood goes with almost everything.

thumbnailzdgg.thumb.jpg.0f2577fb9efd3b2b9049d15b275803b0.jpg

Edited by SuspectDevice
  • Like 6
Link to comment
Share on other sites

  • 2 weeks later...

Well it certainly isn't shy about letting you know it is ticking.

image.png.30656ba0f8487096b3a5e9ca95b1416d.png

Its actually not too bad (for a 1967 Timex mechanical).

Not exactly COSC, but not bad, given that it is a slightly agricultural bit of 1960s technology, which almost certainly has only been serviced once in its lifetime since it left the Dundee factory all those years ago. Its seems to have survived my servicing reasonably well too, since it is still going strong more than two years later.

Edited by AndyHull
Link to comment
Share on other sites

Thought I'd show the watch I've been wearing for the last few weeks, picked it up and gave it a bit of a clean and a strap I had and so far it's keeping great time can't find any info online about the make though ☹️ (if anyone knows anything I'd be happy to know)

Tried taking the scratches out of the crystal with polywatch but no joy so that might have to be replaced.

 

 

IMG_20210509_080345.jpg

  • Like 2
Link to comment
Share on other sites

@@@@@@@@.thumb.jpg.6c88ec481d9e77ebf16864d1394c9ec3.jpg

This is my next amateur horology victim.

It has been apart twice and I'm still having problems. Maybe the 3rd time will be a charm.

I found a chipped jewel the 1st time & fixed that. The 2nd time was a new mainspring (ETA 900 you have to lift out the train bridge instead of just popping the barrel out)

Anyway...I still like the art deco watches and they apparently call this one a "bottle cap" (Bulova made a bottle cap also)

 

Edited by SuspectDevice
  • Like 2
Link to comment
Share on other sites

2 hours ago, LittleWatchShop said:

Did you hit it with sandpaper first?

For this one, I would work it over with 800 grit (or maybe 600) and then follow up with 2000.  Then polywatch.

The thought of taking sandpaper to a crystal is terrifying

I know it would work but it's still terrifying

Link to comment
Share on other sites

10 minutes ago, Rabtmac said:

The thought of taking sandpaper to a crystal is terrifying

isn't just the sandpaper, you have to use a rotary tool also. Unless you want to spend 4 or 5 hours at it and end with sore arms.

Link to comment
Share on other sites

2 hours ago, Rabtmac said:

The thought of taking sandpaper to a crystal is terrifying

I know it would work but it's still terrifying

With a crystal like that I would start with a small piece (1"x1") of 180 grit wet & dry working under a running tap, then work up through 400, 800, 1500, and 2500, all under running water. Then polish with Solvol AutoSol. Maybe 10 minutes max start to finish and will look like new. 

Link to comment
Share on other sites

On 5/9/2021 at 11:33 PM, Marc said:

With a crystal like that I would start with a small piece (1"x1") of 180 grit wet & dry working under a running tap, then work up through 400, 800, 1500, and 2500, all under running water. Then polish with Solvol AutoSol. Maybe 10 minutes max start to finish and will look like new. 

If that is about a plastic crystal most of the time sandpaper is not needed, abrasive compound works good. 

Even for mineral glass in my experience of doing many I have found that stepping through so many grades of paper is a waste of time and money, two grades plus diamond paste are enough.

Full topic 

 

  • Like 1
Link to comment
Share on other sites

  • 2 weeks later...
  • 4 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.




  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Dell fancy a challenge🤣   https://www.ebay.co.uk/itm/285785684626?itmmeta=01HT29WVJY21Q94C73GYHGBTFX&hash=item428a277a92:g:15YAAOSwNRVmBAUz&itmprp=enc%3AAQAJAAAA0DIe4QLQBW66rSyIMiyBuk8GY%2B86pQ%2BQnxGbcNq7egAGe5DIs9YMmiWJIbZtMSxwNJIiJxuojbq523IeUSBQ6pJEIQ0tfz2ChrBR03BksmKINyklg1IK4GAfAcYY9Hta9wVeSZSZN7ZCNAfZTgKs9c4%2BUIUZ3Qjc3QjUXDn2uPRo1FiYOEewMG5A26EXb%2BclBgrqtbOmM6P3bea%2F8ZImOAXNI1HtbmtMk84pIGoM6ISwaM1PKFuADtTFMccS5e3ZjndCbXYXHrW3CecsV0edw3M%3D|tkp%3ABk9SR8q588nQYw
    • A already know the size movement I have the problem is the dial a had purchased has a dimension 20.6mm wide a want to find a watch case that going to fit the dial perfectly 
    • Hi.  I would like to take issue here regarding battery driven , watches, clocks,etc. I will and do repair these clocks in fact I have sever al in my collection as well as the regular mechanical ones. I have one on my mantle piece over 60 years old tha belonged to my wife’s Aunt,  long gone Iam afraid and it has been cleaned etc and never missed a beat and is accurate. Every one has their preduices as regards Electrical /electronic Horology but I regard it as part of the progress time line of the art of Horology and to be treated as such. Like Darwin’s theory of evolution it evolved.  Two cavemen knocking rocks together and a shard broke off , looking at it he worked out if it was stuck on the end of a stick he would have a spear. Likewise his pal seeing what he was up to picked up a piece  and did the same, now that’s evolution. Some clockmaker decided to build a clock that ran with a battery and no spring to wind up and break, progress and both the mechanical and battery driven clocks evolved, the battery ones got better to the point that if it broke you changed the complete unit. Likewise watches did the same but both can be repaired by people who approach Horology with an open mind without preduice.  We all have our likes and dislikes bu I for one would never dismiss any technology because I don’t like it.   The mobile phone is a good example of modern technology at work as is the automotive industry. There buttons and switches in my car I don’t use because to me they are not nesessary but I still drive the car.
    • I haven't gone through all the reading of what it might be or not. The first thing I would do if nothing obvious stands out is replace the mainspring, you have to start at the source of the power. Nine times out of ten that is the problem.  
    • Haha. You're just in a wicked mood today John 😅
×
×
  • Create New...