Jump to content

Watch of Today


mk3

Recommended Posts

From the best of times to the würst of times.

RIMG0335.thumb.JPG.c65664a9596638545c30fc7dfb7a44f8.JPG

I am not making this up, but the thing didn't actually work until I added a little oil(*). It seems that in order to get the sausages movement moving, you need to add some grease. {Insert double entendre laden sausage joke of your choice here}.

(*) Actually I needed to free it up with a little lighter fluid, then oil the pivots,.

  • Like 1
Link to comment
Share on other sites

Interesting... I have my own Luch 3055 in the shop right now. It began to run intermittently, then stopped... so I gave it a good cleaning and lube, and now while the electronics drive the balance successfully, and the pallet fork is actuating normally, drive isn’t transferring to the train wheels. Interestingly, our local watchmaker is from Minsk, where the Luch was made.

gryf

Link to comment
Share on other sites

5 hours ago, Gryf said:

Interesting... I have my own Luch 3055 in the shop right now. It began to run intermittently, then stopped... so I gave it a good cleaning and lube, and now while the electronics drive the balance successfully, and the pallet fork is actuating normally, drive isn’t transferring to the train wheels. Interestingly, our local watchmaker is from Minsk, where the Luch was made.

gryf

I have two of these things. My blue-dialled one runs faultlessly (touch wood!) whilst this white-dialled one will run for months but does run fast. After re-setting the time, it can be a bit of a bear to get it re-started and I'd always wondered if it wasn't de-hacking properly.

Anyway, I hope your watchmaker can get yours running properly.

Regards.

Link to comment
Share on other sites

Watches of today and a little bit of international cross dressing, who says we 'aint adventurous round here. :devil:

Well what the heck, we Scots have been known to wear the occasional skirt kilt (albeit with a handily placed traditional dirk in our sock to keep the childish crowds from sniggering). 

RIMG0351.thumb.JPG.6a70dafaf0cbf1abffaf399b5b3ea1dc.JPG

First, and arguably the most interesting, a Soviet era Sekonda 17 jewel ladies. Dead on arrival, but now keeping remarkably good time following a service. Man that thing is tiny. The least little shake or sneeze and the those microscopic parts would be in orbit.

RIMG0343.thumb.JPG.035c15e4da7e5e2aaeef3df46e617e32.JPG

A steady hand and a lot of patience got it spruced up, oiled and dialed in to around +5 to +15 sec per day. It is swinging away quite nicely, and it too looks hardly worn. It was remarkably clean and the even the strap looks unworn, though a little dry with age. It doesn't even have any of the usual heavy kinks in it. 

Next up is a a "Unisex" German Krippl (with an Epson Japanese movement). Picked up in a job lot in brand new unworn condition still with protective film, but dead battery. Not unattractive, but neither is it very exciting.

Finally the current daily work watch (the Swatch is taking a well earned rest) - the Lorus day date quartz, which you may have spotted in a few other posts.

Edited by AndyHull
Link to comment
Share on other sites

Fine for life onboard a submarine perhaps, but not much use for timing the air remaining in your tanks. It doesn't even appear to be waterproof. They could at least have gone to the trouble of kidding us on that waterproof to 3mm was a thing.

Mind you, some watches go completely overboard with their claims (pun intended).

Examples here.

Jo24LzoRRmeBfK03mcCk_tmp4290301516201328

If I end up 15,000m under water, I doubt if I will be worrying what time it is anymore, since I will presumably be on a different planet.


The maximum known depth of water on planet earth is 10,994 metres (36,070 ft) (± 40 metres [130 ft]) at the southern end of a small slot-shaped valley in its floor known as the Challenger Deep.[2] However, some un-repeated measurements place the deepest portion at 11,034 metres (36,201 ft). (Source - Wikipedia).

Edited by AndyHull
  • Like 1
Link to comment
Share on other sites

Yesterday's little Seconda put in a pretty impressive performance for such a tiny movement.

1731104062_Timegrapherat2019-06-0614-39-48.thumb.png.e5d4d1ca47f79bd07eeebbe8e5fcea53.png

Here it is more than 24hrs later, still ticking away strongly (but starting to flag slightly, judging by the slight increase in rate).

You will be glad to hear I've stopped wearing it now and gone back to something a bit more masculine. :P People were beginning to talk.

Link to comment
Share on other sites

Replacing the Seconda is this Casio AQ 230 with a nice crisp black dial.

RIMG0366.thumb.JPG.45b3f816510a7af15baa94e959f15fa8.JPG

The crystal still needs a little bit of the shine restored to it, but it makes a nice companion for the white dial version I have, which I posted about back in February.

RIMG1266.JPG

Edited by AndyHull
  • Like 1
Link to comment
Share on other sites

Todays (old) new watch is this Brunoff quartz chrono using a Miyota movement.

I bought this years ago for a project which just didn't work, during the course of storage disassembled and reassembly I lost one of the sub dial hands hence why the 24 hour sub dial has none but (usually) I know if it's morning or night.

So this is legitimately the first time wearing out of the box. Just that it's been there years and in bits more than once ish.

20190607_125940.jpg

  • Like 2
Link to comment
Share on other sites

34mm UMF from the good ol’ GDR with its 0j UMF 23.

This was a relatively short-lived (1961 – 1963) movement before being superseded by the easier (and cheaper) to manufacture UMF 24 series which then went on to sell more than 100 million units, mainly to the West.

Regards.

 

UMF G.p. 2019 6.JPG

UMF G.p. UMF 23 2019 2.JPG

  • Like 1
Link to comment
Share on other sites

On 6/6/2019 at 9:31 AM, AndyHull said:

Fine for life onboard a submarine perhaps, but not much use for timing the air remaining in your tanks. It doesn't even appear to be waterproof. They could at least have gone to the trouble of kidding us on that waterproof to 3mm was a thing.

Mind you, some watches go completely overboard with their claims (pun intended).

Examples here.

Jo24LzoRRmeBfK03mcCk_tmp4290301516201328

If I end up 15,000m under water, I doubt if I will be worrying what time it is anymore, since I will presumably be on a different planet.


The maximum known depth of water on planet earth is 10,994 metres (36,070 ft) (± 40 metres [130 ft]) at the southern end of a small slot-shaped valley in its floor known as the Challenger Deep.[2] However, some un-repeated measurements place the deepest portion at 11,034 metres (36,201 ft). (Source - Wikipedia).

I would hate to think of the pressure.

Link to comment
Share on other sites

1973 Timex Marlin - This really was a diamond in the rough. The crystal probably needs replacing, but I managed to get the rather obvious dings and gouges in it smoothed out to the point where they are hardly noticeable, with the possible exception of the one over the day and the even more obvious one at half past one.

RIMG0477.thumb.JPG.22165f2217e47aa78646e0b8bf7ce1af.JPG

I also gave it deep clean, followed by a quick service and replaced the sticking crown locking lever. These tend to wear to the point where you can no longer pull out the crown. I have managed to file them back to life, but I had a spare, so I just did a quick swap.

RIMG0473.thumb.JPG.0c2465bc02207a1df0940fbe0b2a14d8.JPG

It now winds, hands adjust, it runs, and you can easily see the time none of which was possible when it arrived.

A fresh leather band replaced the insanitary hair puller, and it was fit to wear. I'll do the final tinkering and polishing once it has proved itself reliable, on my wrist for a couple of days.

  • Like 1
Link to comment
Share on other sites

Today I pulled out a seldom worn Crepas L'ocean....  

Here's the link to their site....  http://www.crepaswatches.com/styled/photos-4/index.html

There are quite a few features on this watch and although it does have a presence , I find it very comfortable to wear .

It comes with the Stainless Steel Bracelet , and also a silicone bright Blue strap with the link to clear he crown .

 

1807666969_ScreenShot2019-06-08at8_08_03PM.thumb.png.7eeac05be75dfb66820d04996f09b9f7.png

146800158_ScreenShot2019-06-08at8_08_42PM.thumb.png.e91de9b977499026a38cac655aa3b361.png

1509836118_ScreenShot2019-06-08at7_54_46PM.thumb.png.ee57409b5da553d6691052c0ae68bf19.png

 

  • Like 3
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.




  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Welcome my friend. 
    • Been there. Worn that Tshirt.  'ping'. Hands and knees. Nothing. Nada. 20 minutes? Ha! I found it 7 month later. How? Well, after advice from a member, I invested in a £4 UV light torch.  Hands and knees looking for a 'ping' from a Sekonda, found them both within 30 seconds. UV makes the jewel shine. easy peasy. Could have taken longer. Just lucky on the location of the search. Hope this helps.
    • Thanks Dell. I thought about silver soldering. Have never done it but would like to give it a go. Do you think to put flux on the butted joint then run the solder in or to maybe brace it with a piece of scrap spring steel?
    • Never and others. Yes, like you I do spend a fair amount of time reading the contents of this forum. I find it better that any other. Clear, lucid, no Prima Donas, and most of all an easy access without adverts. All thanks to Mark. God bless you mate. You give so much to many of us. What if? No Mark? Hypothetically. A forum. I did run a forum for a few years. Really enjoyed it, but became so engrossed that it did affect my health. I gave to to others to run. Not been back. It was very successful and rivalled a number of large paying sites. No adverts, no others but me. I did ask and listen to members comments and it worked well.    Costs Having a domain name, £10 annually.  Register the site with a forum company, free. Build the site using the forum company guide lines, free. It looked and ran almost the same a Mark's. All the same facilities. The cost was only £5 per month, but counted visits (views). If I recall, it was that price for 5,000 views. Each extra 5,000 views increased the price by £2 per month. Success was my own personal undoing. From £5 per month initially, it rose to £60 a month and looked like increasing. This was 10 years ago. I could not afford that, and asked it anyone would like to take over and someone did. I would assume that this is the price that Mark is funding for us all. His return is our continued comments on the internet about his course, and the fact that many of the big names on YouTube mention him as their Tutor. Those of us who have done, and are still using, his course, benefit. In comparison to other courses, I can't believe how cheap it is, and the value is exceptional. It is the structure that gives the value. Long may Mark reign. Ross  
    • Hi all, total newbie to watchmaking and I've had a bit of a mishap. Just completing level 2 and was doing ok, but I was just on the last part of the reassembly of my ST3620 when the balance end stone shot across the room, just as I was trying to see if I had put the correct amount of oil between it and the balance end, aarrrgh! Been on my hands and knees combing the carpet for 20mins looking for it but to no avail. Does anybody know where I can get a replacement from and what to look for please?? Thanks.
×
×
  • Create New...