Jump to content

Grime and film on watch wheels


Recommended Posts

Anyone have any advice on how the remove a film of old grim on watch wheels? With some watches I run it through my cleaning machine and sometimes it just cant get rid of the dull film that is caked on? I use peg wood on the plates but wasn't sure what people use on the wheels.

 

Thanks

Link to comment
Share on other sites

I tend to fiddle away with peg wood and rodico but have on occasion resorted to using a fibre glass scratch brush, it very much depends on the part but if I may have to obtain a replacement part anyway, and there is nothing to lose, scratch brushes can sometimes resolve issues involving rust, oxidisation or old oil that can not be removed with solvents alone. Not to be used on everything, more or less a last resort but just another tool in the box.

Sometimes if it is just discolouration you may have to put up with it. I like Horosolv degreaser and for brass, copper, bronze etc. Priory Polishes Number 1 cleaner is useful for plates and bridges, it brought my Omega Bumper plates up like new, it is however ammoniated so obvious precautions apply.

cheers,

Vic

Link to comment
Share on other sites

I use naphtha (generic name for lighter fluid) in my ultrasonic machine and then slosh the parts in lacquer thinner to remove the oily film left over by the naphtha. As far as I know products such as L&R  cleaning solvent are basically naphtha. 

david

Link to comment
Share on other sites

I tend to soak parts in hairspring degreaser and then use an old childrens toothbrush.

However, deCarle recommends a watch brush, which you can buy here https://www.cousinsuk.com/product/natural-bristle-brushes-handheld

It is no doubt essential, even in this modern era to follow deCarle's advice on cleaning the brush:

IMG_0007.PNG

I assume that the point here is that the chalk, or burnt mutton bone powder, is mildly abrasive.

If you are after a more upmarket finish, then George Daniels describes the process of polishing wheels using wood polishers charged with rouge. He does point out that the wood becomes quickly charged with brass particles which will scratch the surface, so it is important to keep refreshing the face of the polisher...

 

Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Haha. You're just in a wicked mood today John 😅
    • Heres my watch of today, a Smith 13'" RY . My missus bought me this for this Valentines day a bargain 14.99 with a reduction, the seller has occasional 20% off offers now and then so it was about 15ish with delivery. I love Smiths and i love bulleye dials, this is my first one. The watch arrived non working as stated and i knew what was inside and what would be against me, but i enjoy a challenge, we dont expect a lot if anything from pin pallet movements. A balance pivot was broken and i didnt have another staff but i did have another RY with a battered dial so i robbed the balance and tweaked it around to make it work apart from that mostly just a good clean and relubrication. Keyless works are pretty rough by design and the crown is a bugger to get in and out with the dial on, the setting lever hits the dial before it releases it, so a little mod is needed to help that along. Major problem was the pins on the lever were quite worn which make the old tg have a snow storm fit. Its a similar read for most pin pallets, these were brass as was the escape wheel. But perseverance is me, i didn't change the pins but i did spend some time dressing and polishing the worn areas which improved the trace a lot with some straightish lines 😅 and a beat error of .5 . Not sure what the lift angle should be on these and i Wasn't in the mood to work it out and who believes timegraphers anyway, but at the default 52° it runs with 260ish full 210 after 24 hours dial down , the verticals rates were pretty much all over place. So lets just put it in it's superlight aluminium case and see what happens. Been wearing it now for 3 weeks and it's consistently losing around 1.5  minutes a week winding each morning i think pretty good for an old pin pallet watch. I just love this dial, thanks wifey heres my Valentine's gift for yer sweetie x
    • I have a PDF below that will help. The problem was the PDF wasn't designed for this purpose it was designed to tell you what size watch you  have. Then it doesn't take into account movements come conceivably in different thicknesses.   watch-ligne-size-chart.pdf
    • That would be something! Which brings me back to;  
    • you think you're going to sleep tonight you're not, you're going to ponder the question of what makes you think those of the right parts?  
×
×
  • Create New...