Jump to content

Quartz Watch Not Starting After Battery Change


Recommended Posts

Hello!

 

I took my trusty Swiss Army Watch (24221) to an electronics store for a battery change, and they tried a battery that was a hair too thick, then one that was too thin, before we found the proper size (Renata 371 in case anyone has the same problem). However, the watch did not spring back to life. It had worked fine prior to the battery change (except that it was signalling low voltage with that jumpy sweep of the second hand every few seconds). Also, I was present for the whole procedure and didn't see any undue handling or any insulators falling out or anything that could explain it not restarting.

 

 

Does anyone have an idea what the problem could be? I'd prefer not to throw out one of my favorite watches if there is still something that can be done, or at least know how to verify that it is really dead. I read that sometimes the "gears have to be spun" to resuscitate the movement, and that this can be done physically or magnetically. How is that done?

 

I'd appreciate any advice from the highly skilled readership here!

Cheers!

  • Like 1
Link to comment
Share on other sites

I think this is an FE movement. There is a positive contact (the one you slightly unscrew to release the battery). and obviously a negative contact. Make sure the battery is not upside down. The writing on the battery should be facing upwards.

 

The second thing to look for is to make sure the battery isolator is not missing. This, I think, is orange in colour and resides between the lower negative contact - between the negative contact and the lower plate. If the negative of the battery is in any way touching the metal plate of the watch movement (e.g. if the isolator is missing) then the battery will be shorting and the watch will not work.

 

Isolators can easily be overlooked when removing the battery and a less experienced technician will not realise it was there in the first place.

 

I hope this helps.

  • Like 3
Link to comment
Share on other sites

I'd take it to someone else myself, if he was fiddling around with different batteries, he was rubbish & didn't  have a clue! if you take it to the right person they can

 

A. make sure the battery is in properly.

B. do a simple test to see if the movement is running electronically.

C. use something like a witschi cyclonic to clear any debris from the train.

D. diagnose & fix what everys gone wrong!

  • Like 1
Link to comment
Share on other sites

I think some of the (maybe older?) movements need a reset after a battery change. I remember doing it once but it was so long ago I don't even remember the procedure. I believe some section needs to be shorted or something.

 

Recently I had my neighbor watch for a battery change. After replacing with the correct battery number the watch wouldn't run. It checked Ok in the tester (good coil, pulse) and then I dropped it accidentally....when I picked it up it was running again. Please, don't try that at home!

 

Robert

Link to comment
Share on other sites

  • 4 years later...
18 hours ago, Andre99Nunes said:

 

Now I'm not sure if I am being 'trolled', or 'botted', but either way, I can absolutely assure you that this wont work with watch batteries. Once they are dead, they are dead, and no amount of snake oil will bring them back to life. Furthermore, considering how cheap they are, messing about with some half baked re-charging technique that is likely to cause the cell to leak in the longer term is not even going to come close to appearing anywhere on my radar. 

Link to comment
Share on other sites

I've changed a good few that require an 'additional step' in either shorting the + terminal and the case or a press and hold of two or more of the buttons, (if a chrono style quartz with two or more pushers).

Try the latter if you have pushers, press and hold all or variations of for a few seconds to see if anything happens, as above though. Check for an isolator AND if you find one check to see if there is anything printed on it or the inside of the case back, if so these are often instructions on how to reset the watch after a battery replacement.

You may need a loupe or good magnifying glass to read them.

Link to comment
Share on other sites

17 hours ago, AndyHull said:

Now I'm not sure if I am being 'trolled', or 'botted', but either way, I can absolutely assure you that this wont work with watch batteries. Once they are dead, they are dead, and no amount of snake oil will bring them back to life. Furthermore, considering how cheap they are, messing about with some half baked re-charging technique that is likely to cause the cell to leak in the longer term is not even going to come close to appearing anywhere on my radar. 

He's a spammer - and he's now banned. 

  • Thanks 2
Link to comment
Share on other sites

A bunch of good advice above. I remember saying I would never work on a quartz watch but once folks hear you 'fix watches'.....

One trick that has helped me quite a bit is to look at the little stepping motor magnet. Sometimes they gather a tiny chunk of metal something that needs to be removed. Your quartz tester will tell you if the pulse is happening which would be a further clue. At other times I have found that very gently giving a wheel a slight hand to start is all it needs, but this helps mostly with watches that have been stopped for some time. Perhaps try cleaning the battery contacts too....

Good luck

Link to comment
Share on other sites

  • 2 months later...
On 4/15/2019 at 6:44 AM, Hamish said:

A bunch of good advice above. I remember saying I would never work on a quartz watch but once folks hear you 'fix watches'.....

One trick that has helped me quite a bit is to look at the little stepping motor magnet. Sometimes they gather a tiny chunk of metal something that needs to be removed. Your quartz tester will tell you if the pulse is happening which would be a further clue. At other times I have found that very gently giving a wheel a slight hand to start is all it needs, but this helps mostly with watches that have been stopped for some time. Perhaps try cleaning the battery contacts too....

Good luck

Hamish

Thank you so much for your suggestion, it worked, the watch just needed a bit of help to get going again.

Saved me a trip to the jewellers.

 

  • Like 1
Link to comment
Share on other sites

  • 8 months later...

Hi guys, I have a very similar problem with my Wenger (Swiss Army) Commando watch.  The battery ran out a few months ago and I've just got round to replacing it.  I can see the second hand "pulsing" back and forth very slightly every second, but it doesn't move.  The orange isolator is in place.  I've set the time and date and tried another replacement battery, but no joy.

 

Any ideas how I can get it started?  The movement looks almost identical to this one, although the plastic cover is slightly different.  As in the video I'm replacing the original Renata 371 with an Energiser 370/371.

 

Link to comment
Share on other sites

Sadly some ham fisted battery changers, when removing the back of a quartz watch, 'follow through' with the back removing implement and nick an exposed coil, rendering it open circuit, and surprise surprise, it doesn't run with a new battery...............:growl:

  • Like 1
Link to comment
Share on other sites

Thanks both for your replies.

1 hour ago, jdm said:

Give a read to the answers above.

There are no instructions either on the case, in the booklet, or online (as far as I can see).  There is a tiny hole in the cover with an arrow pointing to it.  I have poked it to see if it's some kind of short or reset, but to no effect - maybe it's for lubrication?  I don't have a tester, and don't have screwdrivers small enough to open the cover of the movement (though I could buy some).  It was only an occasionally worn watch so it's very clean inside.

1 hour ago, JohnD said:

Sadly some ham fisted battery changers, when removing the back of a quartz watch, 'follow through' with the back removing implement and nick an exposed coil, rendering it open circuit, and surprise surprise, it doesn't run with a new battery...............:growl:

I certainly am a ham fisted battery changer, but I don't think I did this.  My continuity tester shows resistance between the battery terminals, which hopefully is a good sign.

Link to comment
Share on other sites

11 minutes ago, GlasWolf said:

Thanks both for your replies.

There are no instructions either on the case, in the booklet, or online (as far as I can see).  There is a tiny hole in the cover with an arrow pointing to it.  I have poked it to see if it's some kind of short or reset, but to no effect - maybe it's for lubrication?  I don't have a tester, and don't have screwdrivers small enough to open the cover of the movement (though I could buy some).  It was only an occasionally worn watch so it's very clean inside.

I certainly am a ham fisted battery changer, but I don't think I did this.  My continuity tester shows resistance between the battery terminals, which hopefully is a good sign.

What you must see is continuity (usually about 2Kohms) across the coil, but to do this you usually have to remove the circuit so as not to get a false reading...

 

  • Like 1
Link to comment
Share on other sites

34 minutes ago, JohnD said:

What you must see is continuity (usually about 2Kohms) across the coil, but to do this you usually have to remove the circuit so as not to get a false reading...

Don't think I'll be doing that!  I'm getting 3Kohms between terminals, not sure whether that's meaningful or not.  Nothing on the coil itself, I assume it's coated.

 

36 minutes ago, watchweasol said:

Hi  Have you got the case back off =, If so what make is the module. Can you supply close up pics of the movement..   The hole you mentioned marked push is for stem removal. Them perhaps I can find the tech sheets for this module and be of some help.   Cheers

It's a Wenger 70160 watch, all I know about the movement is what's written on it.  As I said, I don't have a small enough screwdriver to open the movement cover itself, but could get a super cheapy set if it's worth a bet that they'll help.

Wenger Back.JPG

Wenger Front.JPG

Link to comment
Share on other sites

18 minutes ago, GlasWolf said:

Don't think I'll be doing that!  I'm getting 3Kohms between terminals, not sure whether that's meaningful or not.  Nothing on the coil itself, I assume it's coated.

 

It's a Wenger 70160 watch, all I know about the movement is what's written on it.  As I said, I don't have a small enough screwdriver to open the movement cover itself, but could get a super cheapy set if it's worth a bet that they'll help.

Wenger Back.JPG

Wenger Front.JPG

Looks to be some coil damage here:-

B2RXDac.jpg

Just where you would catch it if the screwdriver slipped when undoing the battery clamp screw.......

The movement is a Ronda 517, which can be obtained new HERE for £7.14...

Edited by JohnD
Link to comment
Share on other sites

Think you might be right, John - it's from pushing aside the clip, I think.  It's actually clearer in the photo than it is in real life.  What a shame.

 

Is the movement glued to the back of the face?  Would it be possible to remove the crown and swap it without specialist tools?  I'm not normally as clumsy as this, I promise...

Link to comment
Share on other sites

Surely if the second hand is "pulsing" then the coil / circuits are OK, and the problem is a mechanical one? Such as dust or dried/sticky oil gumming up the works. Before delving into a replacement movement try a small quantity of lighter fluid on the mechanical parts (not so much that it floods through and stains the dial) &/or invest in a demagnetiser / line release tool which will spin the hands quickly, usually freeing up the movement. 

Good luck

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • This is a very sad day for the industry.. For most of us being amateurs the cost of replacing parts for ETA,s etc will be beyond affordability for the customers.   see full statement below   We have now received the decision from Judge Michael Green on whether or not the High Court has jurisdiction to hear our claim against Swatch, and sadly it is not the decision we had hoped for.   As we have pointed out in previous news items (see below),the rules that Judge Green had to apply strictly prevented him from examining in any way how the Swiss Court arrived at its verdict, even if it is blatantly obvious that the verdict is wrong.   As Swatch’s lawyer was summing up in the last few minutes oft he hearing, the Judge twice pinned him asking if it was alright if, as a result of the Swiss verdict, consumers had to pay 50% more for their watch repairs. After some stumbling, their lawyer’s reply was “Yes”, so  I am quite sure that Judge Green left his court fully aware that the Swiss verdict does not reflect the norms of British Competition Law. However, the rules simply do not allow him to take that simple fact into account.   Judge Green noted that our two arguments relating firstly to British Competition Law now being different from that of the EU, and secondly to the contention that the legality of the Authorised Service Networks has not been tested, had both been mentioned in the Swiss verdict. Because they had been mentioned, he felt that to allow us to argue them again would constitute re examining the Swiss case, and could not be allowed.   As to our claim that we were denied our right to be heard because our evidence was not considered, our lawyers had argued that the evidence we provided could not have been looked at because had the Swiss Court done so, it could not have reached the conclusion that it did. In his verdict, Judge Green highlighted general statements in the Swiss verdict that evidence had been looked at, and acknowledged the arguments we made to him, but again he considered that this was re-examining the Swiss verdict, and could not be permitted.   Our case has attracted considerable interest within the Legal community, and within minutes of the decision being made public we were approached for comment by one of the largest subscription news services, Global Competition Review. They asked us two very pertinent questions, and I reproduce them for you below along with our responses, as they neatly summarise the consequences arising from our case.   What are the key takeaways?   Enormous damage has been done to the fundamentals of UK and European Competition Law by the Swiss courts. It has always been the case that the effect on consumers and competition has to be considered in any decision making, but we now have a ruling that states even monopolists can remove wholesale markets from the supply chain without any consumer benefit based justification. Those entities looking to subvert Competition Law and exploit consumers for their own benefit will be looking at this very carefully.   Has the court made the wrong decision? If so, will you appeal?   The issue lies not with the High Court, but rather with cross border jurisdiction treaties that have no requirement in them for foreign jurisdictions applying UK law to take account of the Ratio Legis [a legal term for the fundamental reasoning why the law was written] of that law, and have no remedy within them for UK Courts to overcome decisions that clearly do not.    After eight years of work, and a very considerable sum in legal costs, I can not begin to tell you how disappointed I am at this outcome. For the time being, there is no further route through the British Courts that Cousins can follow. However, I promised that we would fight to the end, and that promise stands.   The UK is no longer part of the Lugano Convention, whose rules Judge Green has applied, and as yet nothing permanent has replaced it. The political tide turned against repair prevention by restricting supply of spare parts some time ago, and our efforts on behalf of the Watch Repair industry have resulted in high level contacts within several Government Departments. You can be sure that we will keep working to overcome this unjust situation that we now all find ourselves in.    I will keep you advised.   Kind regards   Anthony
    • Dell fancy a challenge🤣   https://www.ebay.co.uk/itm/285785684626?itmmeta=01HT29WVJY21Q94C73GYHGBTFX&hash=item428a277a92:g:15YAAOSwNRVmBAUz&itmprp=enc%3AAQAJAAAA0DIe4QLQBW66rSyIMiyBuk8GY%2B86pQ%2BQnxGbcNq7egAGe5DIs9YMmiWJIbZtMSxwNJIiJxuojbq523IeUSBQ6pJEIQ0tfz2ChrBR03BksmKINyklg1IK4GAfAcYY9Hta9wVeSZSZN7ZCNAfZTgKs9c4%2BUIUZ3Qjc3QjUXDn2uPRo1FiYOEewMG5A26EXb%2BclBgrqtbOmM6P3bea%2F8ZImOAXNI1HtbmtMk84pIGoM6ISwaM1PKFuADtTFMccS5e3ZjndCbXYXHrW3CecsV0edw3M%3D|tkp%3ABk9SR8q588nQYw Darwin’s theory of evolution has not been proven to be absolutely.  😀 
    • A already know the size movement I have the problem is the dial a had purchased has a dimension 20.6mm wide a want to find a watch case that going to fit the dial perfectly 
    • Hi.  I would like to take issue here regarding battery driven , watches, clocks,etc. I will and do repair these clocks in fact I have sever al in my collection as well as the regular mechanical ones. I have one on my mantle piece over 60 years old tha belonged to my wife’s Aunt,  long gone Iam afraid and it has been cleaned etc and never missed a beat and is accurate. Every one has their preduices as regards Electrical /electronic Horology but I regard it as part of the progress time line of the art of Horology and to be treated as such. Like Darwin’s theory of evolution it evolved.  Two cavemen knocking rocks together and a shard broke off , looking at it he worked out if it was stuck on the end of a stick he would have a spear. Likewise his pal seeing what he was up to picked up a piece  and did the same, now that’s evolution. Some clockmaker decided to build a clock that ran with a battery and no spring to wind up and break, progress and both the mechanical and battery driven clocks evolved, the battery ones got better to the point that if it broke you changed the complete unit. Likewise watches did the same but both can be repaired by people who approach Horology with an open mind without preduice.  We all have our likes and dislikes bu I for one would never dismiss any technology because I don’t like it.   The mobile phone is a good example of modern technology at work as is the automotive industry. There buttons and switches in my car I don’t use because to me they are not nesessary but I still drive the car.
    • I haven't gone through all the reading of what it might be or not. The first thing I would do if nothing obvious stands out is replace the mainspring, you have to start at the source of the power. Nine times out of ten that is the problem.  
×
×
  • Create New...