Jump to content

How Do You Fit A Vintage Omega Seamaster Crystal?

systeman
 Share

Recommended Posts

systeman WRT Addict

systeman

Posted
Posted

Hi all,

 

I'm new to the forum and am sure I'll be learning a lot.

 

I recently purchased an old Omega Seamaster from a well known auction site. I took a bit of a gamble, it looked in a right old state with a cracked crystal, broken bracelet, covered in crud and with a slightly pitted dial.

 

The reason I purchased it was I have never owned an Omega and always wanted an older style that could be restored. This one looked as if it had never or hardly ever been opened, and thus serviced.

 

It has a 562 movement housed in a 166.003 case and with a crosshair dial.

 

In taking the back off, the gasket was an off white colour and as hard as rock, it must have been the original. The movement initially looked to be clean but the rotor does need attention - to be expected I suppose as the watch is from 1966 according to the serial number.

 

I've removed the old gasket, the easiest way was to pop out the crystal first, just used my thumbs for that, then I warmed up the case in hot water for about ten minutes, this softened the gasket enough to insert an old screwdriver to carefully remove the gasket in sections.

 

I removed the steel bezel using a razor blade and gently pushing the blade between the bezel and case and using a rotating action, it popped off nicely. Lots of crud under that.

 

I've given the case an ultrasonic clean and light polish ready to receive a new crystal.

 

My question is this:

 

I have sourced from Cousins a new crystal, PZ1543L, for the 166.003 case. Is this to be inserted with a press tool or by using the crystal lift/insert type?

 

 

 

 

post-236-0-77938700-1402481250_thumb.jpg

post-236-0-07401400-1402481312_thumb.jpg

Link to comment
Share on other sites
Geo Distinguished Member

Geo

Posted
Posted

Welcome to the forum Systeman.

That will be a nice watch once refurbished. Regarding the crystal, if it has a tension ring inside the perimeter of the lens then it will have to be pressed in, if the crystal is plain and does not have a tension ring use a crystal lift to compress it for fitting.

Link to comment
Share on other sites
  • 2 weeks later...
systeman WRT Addict

systeman

Posted
  • Author
Posted

Thanks Lee, I practiced a few times with a cheapo crystal before finally fitting the Omega genuine one. I wasn't sure if the correct procedure was to fit it without the steel bezel in situ or removed. I took some measurements and decided to fit it with the bezel removed, pressing the bezel in place afterwards.

 

Because the bezel is slightly larger than the crystal, I think the only purpose it serves on this Seamaster version is to serve as a crystal alignment guide and to protect the crystal edge because of its height.

 

It would be nice to know which way up the Omega symbol should be. On the PZ5143L one I fitted it was inverted, i.e. date lense at 3pm - Omega logo inverted. Does it matter?

Link to comment
Share on other sites
systeman WRT Addict

systeman

Posted
  • Author
Posted

Thanks Lee, I practiced a few times with a cheapo crystal before finally fitting the Omega genuine one. I wasn't sure if the correct procedure was to fit it without the steel bezel in situ or removed. I took some measurements and decided to fit it with the bezel removed, pressing the bezel in place afterwards.

 

Because the bezel is slightly larger than the crystal, I think the only purpose it serves on this Seamaster version is to serve as a crystal alignment guide and to protect the crystal edge because of its height.

 

It would be nice to know which way up the Omega symbol should be. On the PZ5143L one I fitted it was inverted, i.e. date lense at 3pm - Omega logo inverted. Does it matter?

 

By crystal alignment guide I mean if the bezel is in situ before fitting the crystal.

Link to comment
Share on other sites
  • 3 weeks later...
  • 1 year later...
rogart63 Distinguished Member

rogart63

Posted
Posted

Thanks Lee, I practiced a few times with a cheapo crystal before finally fitting the Omega genuine one. I wasn't sure if the correct procedure was to fit it without the steel bezel in situ or removed. I took some measurements and decided to fit it with the bezel removed, pressing the bezel in place afterwards.

 

Because the bezel is slightly larger than the crystal, I think the only purpose it serves on this Seamaster version is to serve as a crystal alignment guide and to protect the crystal edge because of its height.

 

It would be nice to know which way up the Omega symbol should be. On the PZ5143L one I fitted it was inverted, i.e. date lense at 3pm - Omega logo inverted. Does it matter?

The logo in the crystal could be either way. I have seen all directions. They are random stamped? As long as it is there . BTW that is a very nice looking watch. 

Link to comment
Share on other sites
Alaskamick WRT Addict

Alaskamick

Posted
Posted

The crystal should,in my opinion, be fitted so that it is in the same orientation as the logo on the dial.

 

It makes no difference really which way it goes as you only see it if you're looking for it but I can't believe that in the old days a company like Omega would allow watches to go out with their logo upside down.

Link to comment
Share on other sites
ramrod Super WRT Addict

ramrod

Posted
Posted

systeman - you've just done what i've been wanting to do for a while. i want to get an old omega and refurbish it. i love omega watches. it's almost a grail for me.

you've done a real nice job on yours. you should be proud - and you should be wearing it every day. lol.

Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
Posted

The crystal should,in my opinion, be fitted so that it is in the same orientation as the logo on the dial.

 

It makes no difference really which way it goes as you only see it if you're looking for it but I can't believe that in the old days a company like Omega would allow watches to go out with their logo upside down.

Agree. It has to be fitted properly or you might as well forget it. There's a right way and there's a wrong way

Link to comment
Share on other sites
 Share
Go to topic listing


  • Similar Content

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Zedster
      Movement inserted from crytal side

      By Zedster · Posted

      Hi, guys I have a bit of a predicament and hopefully, somebody can advise. I'm working on a Roamer MST 521 where the movement is extracted from the crystal side. I'm now at the final hurdle where I need to replace the movement back into its case but I'm not sure of the correct procedure. I still need to fit the hands but that's where the problem lies. If I insert the winding stem to test the hands for correct alignment I will need to turn the movement over to release the stem again it's the spring-loaded type and needs a small bit of force to push down but with the hands fitted, I don't think I can do this on a cushion without causing some damage to the hands and that's the last thing I want to do, this watch has already been a love-hate relationship and I'm so close to boxing this one off which I'm counting as my first major project.  The other option is to case the movement then fit the hands and hope everything is okay. I've already broken the original winding stem but managed to find a replacement, the last one in stock, so I'm a bit reluctant to keep removing it. Any suggestions would be appreciated. 
    • Jon
      Main spring

      By Jon · Posted

      I would go for the dearer spring. You won't need to remove the spring from the carrier ring and then use a mainspring winder to get it into the barrel, for a start. Also that spring is closer to the needed dimensions, especially the length. The length plays a part in the mainsprings strength. If you double the length you will half the force (strength) of the spring and vice-versa. A spring with 20 mm less length would be about 7% shorter, so technically would be 7% more strength, but I find halving this number is closer to real-world findings, so the spring would be about 3 to 4% more strength/force. On a mainspring that ideally kicks out 300 degrees of amplitude, a 3% increase in amplitude would be 309 degrees. Increasing or decreasing the length of the mainspring will affect the power reserve to a greater or lesser degree. It depends how much shorter or longer it is.
    • Malocchio
      What tools does ebay have to offer this week.

      By Malocchio · Posted

      I recently bought this but not on ebay. I figured if I want something Japanese I better check Japanese auction sites since these don't seem to pop up on ebay. I paid 83 € plus shipping & taxes. I think it was pretty reasonable for a complete set in good condition.
    • GuyMontag
      1972 Bulova President "E" Sea King 11ACACB movement

      By GuyMontag · Posted

      Did you take the friction pinion off the large driving wheel and grease it? Although, now that I think about it, that shouldn't have any effect on the free running of the train if the friction pinion isn't interacting withe minute wheel/setting wheel...
    • DDean
      Incabloc Lyre Spring & Low Earth Orbit

      By DDean · Posted

      I did in fact use Rodico to get the spring into general position and "hold" it there while I used a fine oiler to make subtle positional adjustments.
×
×
  • Create New...