Jump to content

How i make a watch stem


Recommended Posts

A friend of mine asked if i want to make a stem for him. I have improved my hardware and wanted to try so happily accepted :)

Not in the Dremel now. Here the pulley wheel is serving as a dividing plate with 4 holes making sure that the rectangle cross-section will be perfect. Turning with help of a microscope, no loupe at all. 

2016-10-07_15_18_06.jpeg

2016-10-07_17_49_00.jpeg

A thin glass strip is hot glued on the "T-rest" which has two purpose. The file is sliding on it easily and it is making sure that the sides will be parallel.

2016-10-07_17_49_08.jpeg

2016-10-08_14_59_38.jpeg

Still a lot to file down.

The workpiece is a spoke of a Chehoslovak Favorit road racer. Even tungsten carbide is softer if hardened.

  • Like 5
Link to comment
Share on other sites

Finaly i got something similar to a winding stem.... for the 6th try.... 

20161016_142231.jpeg

M1.2 thread done. The stem here was turned down to 1.15mm to make sure it wont break while tapping. 

20161017_181000.jpeg

After heated to red and dropped in brine. It is so hard and brittle, i can hear it whizzling near my ear :)

20161017_191123.jpeg

Using my special top quality heating pan

20161017_192510.jpeg

Annealed. Not as shiny like on pictures one can find on pro-watchmaker school sites, but the color tells me the temperature and that is important.

20161017_192910.jpeg

 And the best thing is, i dont had the movement. So there might be a big surprise for the guy i made it if it wont work :)

Edited by szbalogh
Link to comment
Share on other sites

On 2016. 10. 18. at 0:00 AM, MilTimeCan said:

I am in awe.

Wow, I worked on a lot of plastic model aircraft parts in my younger days, but I have never seen anything like this. 

Sir, you are a pro !

Not a pro for sure :) Just so excited while discovering this new watchmaking world. For an experienced watchmaker this is an every day job :) And i am sure i could make it better. For example if i had a glass fiber scratch brush, then the bluing would be better. Also i am not satisfied with the setting lever slot.The rectangular edges here are not perfect. I will have to grind a better graver to cut this type of slots.

Made a video of this project, threading included.

 

Edited by szbalogh
  • Like 5
Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Many thanks for your advice (being borne in mind at present) & offer Dell. When I was given the clock the plastic anchor was loose on the arbour (it had split at the 'hole') &, after repairing this, I have been trying to determine whether the spindle (pin) should be perpendicular when the pallet is sitting on a flat surface; or whether, when installed, its L-R extremes (or alternatively its tick & tock points) should lie at equal angles from the vertical when moved with spring absent. I can get the clock to run but in every such configuration the top block has to be turned anti-clockwise (from above) by quite a bit in order to be 'in beat' & it always runs fast (despite the pendulum being set to as slow as possible). This makes me wonder if there is any particular feature of/fault in a torsion spring clock which determines which turn direction (if any) is necessary to get it 'in beat'; & whether there would be a different set of settings that would get it running nearer to time at somewhere around the mid timing/inertia position which would then allow tweaking of the fast/slow setting.
    • Now this has happened I bet China or India just to name two will start to produce none genuine parts.  I did. But idiot Boris Johnson failed miserably in his negotiations. The E U stitched up the UK like a kipper. Nigel Farage  offered his help but big head Boris declined. So this is why we are in this mess all because Johnson wasn't clever enough.  
    • Hands up all those who voted to leave the EU 😂, oopsie.  UK has just signed the Hague convention, next year that will provide cross border clout to British courts.
    • Ive heard about that oil before for the lever pins. I found it easy to work on , it didn't have a whole lot of pivot wear but i bit sloppy on the lever cock, i think you have to live with what you have or bin it. Stiff to wind and set ?  Not a cannon pinion issue that has no friction thats made up further back and if I remember the barrel drives the hour wheel. No problem on this one .Let me know when you start it as i have another that donated to this one, i can work alongside you with it, two heads are better than one. 
×
×
  • Create New...