Jump to content

Agat/Kirovskie/Zlatoust 4282 stopwatch disassembly and repair


Recommended Posts

Receíved two stopwatch movements recently (the two on the right). One was a full movement, the other one had the barrel missing. Also had a case with a Zlatoust dial and a movement containing only the mainplates and the dial side complications. So i decided to make one working stopwatch with the older dial (lookng better in my opinion).

2016-09-21_19.04.14.jpeg

DONT TRY TO REMOVE THE HANDS!!!  The dial is fixed by two grub-screws found at the movement side. DONT EVEN TRY TO REMOVE THE HANDS!!! Pull upp the dial, the hands will be also lifted. You can see two hearth-shaped steel plates with a steel tube in the next picture taken from the dial side. The steel tube has a brass tube pressed on it, which actually holding the hand. The hand is riveted on the brass piece. Secured position of the hands on the hearth-shaped plate ensures that they always jups to 0 at reset. The hearth-shaped plates are spring-mounted on the wheel pinions, so if one lifting the dial the springs will let off the pinion. I wanted to change the dial so tried to remove the hands. The result is one bent second hand (the big one) and a broken minute hand. It seems that it will be a pain mounting the hands back in the proper position.

2016-09-21_19.06.11.jpeg

2016-09-21_19.08.01.jpeg

At first the movement seemed to be a complicated one, but the disassembly is pretty straightforward. 

Release the tension of the springs first by unhooking them. All of them are mounted with screws so they wont fly away. 

2016-09-21_19.09.48.jpeg

2016-09-21_19.11.25.jpeg

Then just remove the levers one by one.

2016-09-21_19.11.53.jpeg

2016-09-21_19.12.47.jpeg2016-09-21_19.13.10.jpeg

The next lever has a pin for stopping the balance wheel.

2016-09-21_19.13.30.jpeg

And finally the column wheel. The last lever spring didnt wanted to come off so i just left it there.

2016-09-21_19.13.55.jpeg

There is nothing unusual on the movement side. First take off the balance assembly.

2016-09-21_19.16.26.jpeg

2016-09-21_19.17.31.jpeg

2016-09-21_19.17.46.jpeg

(Last chance to let down the mainspring tension!)

Then the pallet fork. 

2016-09-21_19.19.28.jpeg

2016-09-21_19.22.38.jpeg

Ratchet wheel, click, and clickspring dismounted.

2016-09-21_19.23.54.jpeg

2016-09-21_19.24.31.jpeg

The crown wheel is mounted with a spring loaded slipping plate. This is so russian... simpe and easy. 

And finally take down the three screws holding the main plate.

2016-09-21_19.25.59.jpeg

I would like to mention it here, that the whole thing is so ... russisan :) All parts are rough and "has material in it". Pinions are thick....

I could see oil residues on the pallet staff pinion, which was cogged (where it is ususally not needed) and on one of the gear pinions. 

No sign of oil in the barrel. I could evel let it down lamely.

Nothing special at disassembly, just push down and the cover will pop off. No cleaning needed here, i will just add oil. 

2016-09-21_19.28.50.jpeg

Balance disassembly, pretty streightfoward. 

2016-09-21_19.32.44.jpeg

Yes, both end of the balance is broken. It has some "russian amount" of shellac on the impulse jewel. 

2016-09-21_19.39.10.jpeg

And ready for repivoting. 

2016-09-21_19.44.54.jpeg

Edited by szbalogh
  • Like 2
Link to comment
Share on other sites

  • 10 months later...

Received a good lot of ~200-300 balance staffs from a friend and found some staffs for the Agat stop watch. Replaced, serviced. Now working like a charm :)

Still need to make a minute hand since i ruined the original one and a new crystal.

Untitled.thumb.png.6be54cc0174413723f9b5503d820b4c4.png

Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • This is a very sad day for the industry.. For most of us being amateurs the cost of replacing parts for ETA,s etc will be beyond affordability for the customers.   see full statement below   We have now received the decision from Judge Michael Green on whether or not the High Court has jurisdiction to hear our claim against Swatch, and sadly it is not the decision we had hoped for.   As we have pointed out in previous news items (see below),the rules that Judge Green had to apply strictly prevented him from examining in any way how the Swiss Court arrived at its verdict, even if it is blatantly obvious that the verdict is wrong.   As Swatch’s lawyer was summing up in the last few minutes oft he hearing, the Judge twice pinned him asking if it was alright if, as a result of the Swiss verdict, consumers had to pay 50% more for their watch repairs. After some stumbling, their lawyer’s reply was “Yes”, so  I am quite sure that Judge Green left his court fully aware that the Swiss verdict does not reflect the norms of British Competition Law. However, the rules simply do not allow him to take that simple fact into account.   Judge Green noted that our two arguments relating firstly to British Competition Law now being different from that of the EU, and secondly to the contention that the legality of the Authorised Service Networks has not been tested, had both been mentioned in the Swiss verdict. Because they had been mentioned, he felt that to allow us to argue them again would constitute re examining the Swiss case, and could not be allowed.   As to our claim that we were denied our right to be heard because our evidence was not considered, our lawyers had argued that the evidence we provided could not have been looked at because had the Swiss Court done so, it could not have reached the conclusion that it did. In his verdict, Judge Green highlighted general statements in the Swiss verdict that evidence had been looked at, and acknowledged the arguments we made to him, but again he considered that this was re-examining the Swiss verdict, and could not be permitted.   Our case has attracted considerable interest within the Legal community, and within minutes of the decision being made public we were approached for comment by one of the largest subscription news services, Global Competition Review. They asked us two very pertinent questions, and I reproduce them for you below along with our responses, as they neatly summarise the consequences arising from our case.   What are the key takeaways?   Enormous damage has been done to the fundamentals of UK and European Competition Law by the Swiss courts. It has always been the case that the effect on consumers and competition has to be considered in any decision making, but we now have a ruling that states even monopolists can remove wholesale markets from the supply chain without any consumer benefit based justification. Those entities looking to subvert Competition Law and exploit consumers for their own benefit will be looking at this very carefully.   Has the court made the wrong decision? If so, will you appeal?   The issue lies not with the High Court, but rather with cross border jurisdiction treaties that have no requirement in them for foreign jurisdictions applying UK law to take account of the Ratio Legis [a legal term for the fundamental reasoning why the law was written] of that law, and have no remedy within them for UK Courts to overcome decisions that clearly do not.    After eight years of work, and a very considerable sum in legal costs, I can not begin to tell you how disappointed I am at this outcome. For the time being, there is no further route through the British Courts that Cousins can follow. However, I promised that we would fight to the end, and that promise stands.   The UK is no longer part of the Lugano Convention, whose rules Judge Green has applied, and as yet nothing permanent has replaced it. The political tide turned against repair prevention by restricting supply of spare parts some time ago, and our efforts on behalf of the Watch Repair industry have resulted in high level contacts within several Government Departments. You can be sure that we will keep working to overcome this unjust situation that we now all find ourselves in.    I will keep you advised.   Kind regards   Anthony
    • Dell fancy a challenge🤣   https://www.ebay.co.uk/itm/285785684626?itmmeta=01HT29WVJY21Q94C73GYHGBTFX&hash=item428a277a92:g:15YAAOSwNRVmBAUz&itmprp=enc%3AAQAJAAAA0DIe4QLQBW66rSyIMiyBuk8GY%2B86pQ%2BQnxGbcNq7egAGe5DIs9YMmiWJIbZtMSxwNJIiJxuojbq523IeUSBQ6pJEIQ0tfz2ChrBR03BksmKINyklg1IK4GAfAcYY9Hta9wVeSZSZN7ZCNAfZTgKs9c4%2BUIUZ3Qjc3QjUXDn2uPRo1FiYOEewMG5A26EXb%2BclBgrqtbOmM6P3bea%2F8ZImOAXNI1HtbmtMk84pIGoM6ISwaM1PKFuADtTFMccS5e3ZjndCbXYXHrW3CecsV0edw3M%3D|tkp%3ABk9SR8q588nQYw Darwin’s theory of evolution has not been proven to be absolutely.  😀 
    • A already know the size movement I have the problem is the dial a had purchased has a dimension 20.6mm wide a want to find a watch case that going to fit the dial perfectly 
    • Hi.  I would like to take issue here regarding battery driven , watches, clocks,etc. I will and do repair these clocks in fact I have sever al in my collection as well as the regular mechanical ones. I have one on my mantle piece over 60 years old tha belonged to my wife’s Aunt,  long gone Iam afraid and it has been cleaned etc and never missed a beat and is accurate. Every one has their preduices as regards Electrical /electronic Horology but I regard it as part of the progress time line of the art of Horology and to be treated as such. Like Darwin’s theory of evolution it evolved.  Two cavemen knocking rocks together and a shard broke off , looking at it he worked out if it was stuck on the end of a stick he would have a spear. Likewise his pal seeing what he was up to picked up a piece  and did the same, now that’s evolution. Some clockmaker decided to build a clock that ran with a battery and no spring to wind up and break, progress and both the mechanical and battery driven clocks evolved, the battery ones got better to the point that if it broke you changed the complete unit. Likewise watches did the same but both can be repaired by people who approach Horology with an open mind without preduice.  We all have our likes and dislikes bu I for one would never dismiss any technology because I don’t like it.   The mobile phone is a good example of modern technology at work as is the automotive industry. There buttons and switches in my car I don’t use because to me they are not nesessary but I still drive the car.
    • I haven't gone through all the reading of what it might be or not. The first thing I would do if nothing obvious stands out is replace the mainspring, you have to start at the source of the power. Nine times out of ten that is the problem.  
×
×
  • Create New...