Jump to content

- Look mommy I made a mainspring flower.

B3stia

By B3stia
in Watch Repairs Help & Advice

 Share

Recommended Posts

jdm Distinguished Member

jdm

Posted
Posted
41 minutes ago, vinn3 said:

thumbs are the way to go,  if you are thin skined or  bleed easly;  use leather gloves.  i forgot to mention "acidic hands"  it could be a problem.   vinn

Try not to use thumbs, it's easy. Left hand keeps coils pressed in the barrel with the flat of the tweezers, right hand (with gloves or finger coats) puts in the spring, and the tweezers follows. Let the tool do the hard contact, not your skin.

 

 

Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted (edited)
2 minutes ago, vinn3 said:

is there a chart somwhere to tell you  which direction YOUR  watch main spring is wound?  IT IS  possible to get it ALL back  together  AND  still not know  WHATS THE HECK WRONG NOW?   vinn

A picture before taking things apart would help I think. And if no picture look at the barrel screw if left of right threaded.

Edited by jdm
Link to comment
Share on other sites
clockboy Distinguished Member

clockboy

Posted
Posted

As you can see by this guy winding a spring by hand is not easy. I used to use his method but I had lots of failures. Also notice that he does not wear finger cots & I suspect no lubrication has not been applied to the spring. My advise is to bite the bullet and purchase a spring winder.

Link to comment
Share on other sites
Cad101 Super WRT Addict

Cad101

Posted
Posted

I've put so many mainsprings back by hand I bet I'm not far off the speed of a winder :DI usually get one coil in then press down on top of the spring using alternate thumbs the spring just follows its natural route around the inside its simple when you've done a few.

  • Like 1
Link to comment
Share on other sites
Vich Distinguished Member

Vich

Posted
Posted

I seem to manage watches ok but only the once I wound a carriage clock spring in by hand and required safety goggles one leather glove and one poly glove.  I will have to be backed into a corner to repeat the experience.

there are a few examples of videos using the winders or by hand to learn from but you do need some luck as well and the skill will appear eventually. Don't give up though - speaking as someone who has probably made a hash of numerous different parts of a watch over the time I have been tinkering.

Cheers,

Vic

Link to comment
Share on other sites
MrBeat WRT Addict

MrBeat

Posted
Posted

One method by hand ive not used in years is placing the arbour in place and holding it very firmly with a pin vice from opposing side of barrel, then with the mainspring hole end fitted to the arbour turn the pin vice to wind the spring in whilst using the tip of your left finger to hold in the primary coil ( using a finger cot of course ). Easier to see in practice than explain in writing but im sure you get the principle :) 

And help to have a good range of pin vices :D

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Rixy
      Broken lug

      By Rixy · Posted

      Thanks Dell. I thought about silver soldering. Have never done it but would like to give it a go. Do you think to put flux on the butted joint then run the solder in or to maybe brace it with a piece of scrap spring steel?
    • rossjackson01
      Without Our Forum

      By rossjackson01 · Posted

      Never and others. Yes like you I do spend a fair amount of time reading the contents of this forum. I find it better that any other. clear, lucid, no Prima Donas, and most of all an easy access without adverts. All thanks to Mark. God bless you mate. You give so much to many of us. What if? No Mark? Hypothetically. A forum. I did run a forum for a few years. Really enjoyed it, but became so engrossed that it did affect my health. I gave to to others to run. Not been back. It was very successful and rivalled a number of large paying sites. No adverts, no others but me. I did ask and listen to members comments and it worked well.    Costs Having a domain name, £10 annually.  Register the site with a forum company, free. Build the site using the forum company guide lines, free. It looked and ran almost the same a Mark's. All the same facilities. The cost was only £5 per month, but counted visits (views). If I recall, it was that price for 5,000 views. Each extra 5,000 views increased the price by £2 per month. Success was my own personal undoing. From £5 per month initially, it rose to £60 a month and looked like increasing. This was 10 years ago. I could not afford that, and asked it anyone would like to take over and someone did. I would assume that this is the price that Mark is funding for us all. His return is our continued comments on the internet about his course, and the fact that many of the big names on YouTube mention him as their Tutor. Those of us who have done, and are still using, his course, benefit. In comparison to other courses, I can't believe how cheap it is, and the value is exceptional. It is the structure that gives the value. Long may Mark reign. Ross  
    • TheQuietMan
      Help please.

      By TheQuietMan · Posted

      Hi all, total newbie to watchmaking and I've had a bit of a mishap. Just completing level 2 and was doing ok, but I was just on the last part of the reassembly of my ST3620 when the balance end stone shot across the room, just as I was trying to see if I had put the correct amount of oil between it and the balance end, aarrrgh! Been on my hands and knees combing the carpet for 20mins looking for it but to no avail. Does anybody know where I can get a replacement from and what to look for please?? Thanks.
    • Dell
      Broken lug

      By Dell · Posted

      Get someone local to tig it ,very easy fix and should only take a few minutes so probably wouldn’t cost much ,or failing that get it very clean and silver solder it. Dell
    • Zedster
      Movement inserted from crytal side

      By Zedster · Posted

      Hi, The winding pin is not split, well that's how it was when I obtained the watch. The movement is front-loaded and here's a picture of where the case screws are fitted. The face picture is before I dismantled it. Quick update.  I've always had a nylon ring sitting in the parts try that I wasn't sure where it went and left it to the last thing as I know it must be part of the case assembly. Anyway, looking at the picture in my last post you can see, just under the winding stem, a white-looking object, this is the nylon ring 🤭 So, I had to remove the dial again and replace the ring. Once this was all back together I placed the movement in the case and realized my initial problem maybe is not a problem as it looks like I can screw the movement back in the case and then place the hands as the dial is nearly flush with the outside of the case anyway so I'll be able to check for alignment. if all is good then just fit the crystal and bezel 🤔 I can't think of any issues with this approach but please comment if you think I've not thought of something. Another lesson learned as well. Take more pictures not just of the movement parts and location 😅
×
×
  • Create New...