Jump to content

Seiko mainspring barrel not opening....

diamondslayer
 Share

Recommended Posts

Lawson Super WRT Addict

Lawson

Posted
Posted

Also a word of caution diamondslayer.  The grease they use in many Seiko barrels is horrible black stuff the makes a nasty mess of anything it touches.  Open those Seiko barrels is my least favorite job :(

 

Link to comment
Share on other sites
Mark Distinguished Member

Mark

Posted
Posted
Generally, Seiko barrels are not meant to be opened. You can still open them insisting a little..

You do need to open them ;)

They have a slightly different cap than a standard barrel. Much the same as a valjoux 7750 barrel. The cap has a rim which extends right down to the barrel teeth tricky to open without damaging the barrel teeth. I find an extremely sharp razor blade is perfect for opening the cap.

On these seikos the mainspring has to come out as they are usually in an awful mess.

Also - note the orientation the mainspring is wound in. It will be the reverse of most Swiss watch barrels.

  • Thanks 2
Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted
Just now, Mark said:

You do need to open them ;)

They have a slightly different cap than a standard barrel. Much the same as a valjoux 7750 barrel. The cap has a rim which extends right down to the barrel teeth tricky to open without damaging the barrel teeth. I find an extremely sharp razor blade is perfect for opening the cap.

On these seikos the mainspring has to come out as they are usually in an awful mess.

Also - note the orientation the mainspring is wound in. It will be the reverse of most Swiss watch barrels.

Thanks Mark. To be honest the only 7S26 barrel that I've opened wasn't difficult at all, and no mess was found inside. I did replace the mainspring, but that didn't seem to make much difference.

Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
Posted

Mark I don't know if you are aware back in  70's and 80's Seiko advised repairs if the the watch was 5 to 10 years old you should replace the whole barrel and not to open it to clean. Up to 5 years there is no need to do anything apart from cleaning the arbor. 

  • Like 1
Link to comment
Share on other sites
Mark Distinguished Member

Mark

Posted
Posted
16 minutes ago, oldhippy said:

Mark I don't know if you are aware back in  70's and 80's Seiko advised repairs if the the watch was 5 to 10 years old you should replace the whole barrel and not to open it to clean. Up to 5 years there is no need to do anything apart from cleaning the arbor. 

Not aware of this - but for two decades I have always opened them up and done what I do with every watch :)

Actually - I have made a video of my method, write or wrong, and will upload it now so you guys can see how mucky they get, and this one was not too bad, Ive seen worse.

I shot a whole video for the 7S26 but have not finished editing it yet.

 

Edit... @oldhippy, I can see why Seiko would recommend this actually as the mainsprings can be damaged very very easily on these.

Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
Posted

We all have our different ways Mark. I think that is one reason why seiko barrels are different and can be hard to open. I look forward to the video, for me its nice seeing other watchmakers working and how the go about their work.

  • Like 1
Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted
26 minutes ago, oldhippy said:

Mark I don't know if you are aware back in  70's and 80's Seiko advised repairs if the the watch was 5 to 10 years old you should replace the whole barrel and not to open it to clean. Up to 5 years there is no need to do anything apart from cleaning the arbor. 

Still the case today. Only barrel complete has a part number (if one can obtain the actual part). Which doesn't mean tha one can't open it anyway and replace MS with a generic part for a small saving.

Link to comment
Share on other sites
Lawson Super WRT Addict

Lawson

Posted
Posted

One thing to mention about not only the 7s26, but many of the older Seiko movements, is that the lower arbor hole is often badly worn and needs to jeweled.  This is because they ran the arbor straight steel to steel, without a bushing.  Without regular servicing intervals these tend to wear badly and put the barrel on a slight tilt, causing the movement to have a lower amplitude.  In severe cases the barrel has tilted so much it's worn the plating off the top of the barrel as it rubs on the bridge, and the brass is exposed.

This fault is seen so frequently where I work, that even if the barrel is fine we jewel the hole as part of the service: as preventative maintenance.

Link to comment
Share on other sites
Lawson Super WRT Addict

Lawson

Posted
Posted
3 hours ago, Mark said:

Actually - I have made a video of my method, write or wrong, and will upload it now so you guys can see how mucky they get, and this one was not too bad, Ive seen worse.

I shot a whole video for the 7S26 but have not finished editing it yet.

NO FAIR MARK!!  You got a clean one. ^_^

Why do I always get the barrels that look like they've been filled with Track-Roller Grease! :pulling-hair-out:

  • Like 1
Link to comment
Share on other sites
Mark Distinguished Member

Mark

Posted
Posted
NO FAIR MARK!!  You got a clean one. [emoji5]

Why do I always get the barrels that look like they've been filled with Track-Roller Grease! :pulling-hair-out:

Lol. Believe me - I've had them.

Link to comment
Share on other sites
Lawson Super WRT Addict

Lawson

Posted
Posted

We get them from our parts department  :P

Seriously, I'm not sure of the cost mate.  We charge it out as "Auto Calendar Service" which is a flat rate of AU$495.00 for any standard 3 hand automatic movement with a date complication.

Sorry I can't be any more specific ... but you simply measure the arbor diameter (ID)  and the broach you used to re-round the hole (OD) ... add a couple of thou to the OD for a press fit, and also check the ID for correct side-shake to get the correct jewel.  Some plates require more broaching then others ... so the size you use can vary slightly for each movement.

I'm sure Mark will make a step-by-step video on jeweling worn bushings one day and it will be all clear.  It's not a difficult job with the correct tools.

  • Like 1
Link to comment
Share on other sites
bobm12 Distinguished Member

bobm12

Posted
Posted
5 hours ago, Lawson said:

I'm sure Mark will make a step-by-step video on jeweling worn bushings one day and it will be all clear.  It's not a difficult job with the correct tools.

I'm looking forward to this very much!

Cheers,

Bob

  • Like 1
Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • oldhippy
      Without Our Forum

      By oldhippy · Posted

      This forum is a big part of my life. When I retired from horology many years ago due to poor health I missed what I had trained for. On here I can still do my bit in helping and advising others and have a little fun as well.  
    • RichardHarris123
      Without Our Forum

      By RichardHarris123 · Posted

      First thing this morning, make coffee, second, check the forum.  I would really miss the forum, not on any social media, not interested in telling the world what I had for breakfast!!! I do consider most of the regulars friends and would wonder what had happened if they stopped posting. 
    • fnick
      Down the rabbit hole!

      By fnick · Posted

      Hi all Thought I'd show my small and trying to keep under control watch collection! Apart from the Enicar all were under £12! At least if I destroy them in the process then I won't be too worse off. A few pics to start off with First of all my first attempt. A Thuya pocket watch. It was only running face down and would stop when vertical. So now it still works face down and only slows down when vertical so at least an improvement! 😄  I only have a generic watch oil at the mo so that won't help but I'm hoping to get some more appropriate oils in a couple of months for my birthday. I did have to get a crystal for it since it didn't come with one. It didn't look as though it would friction fit (and I don't have a crystal press in any case) so I glued it to the case with PVA. So far so good. Next up above are a sekonda and citizen automatic. Both non runners. Both with broken balance wheels amongst other things. I'm hopeful the citizen will start when I get the new one I ordered but the sekonda is being kept for spares and trial of new techniques. And finally the Enicar and the timemaster. Both running when I got them. I wanted to get running watches so that at least I stood a fighting chance of still having a running watch after the service! It was all going well on the Enicar until I dropped the balance wheel during reassembly...😔. Unfortunately they are quite expensive to get so for now I'll won't do anything with it but I would like to fix it at one point. The timemaster is still running (yeah!) but I managed to break a dial foot during the deassembly. First repair attempt failed so now I am looking at soldering it back on... So there we go. My initial foray into this great hobby. Thanks for sticking with this tale so far.  I'm hoping that once the balance wheel arrives for the citizen I will be able to say I bought a non runner and fixed it! So fingers crossed. Thanks for looking, Nick
    • HectorLooi
      Without Our Forum

      By HectorLooi · Posted

      Like losing Ranfft. That was a wake up call. We took his website for granted. Miss him terribly.  
    • Neverenoughwatches
      Without Our Forum

      By Neverenoughwatches · Posted

      Its 4 o'clock in the morning here in the Uk, i cant sleep, i dont sleep, not much ever really. My brain never shuts off to rest, I'm just a constant thinker, i have to be very tired to be able to sleep,  i guess eventually it will be my undoing and my health will suffer because of it I'm sure. But while I'm here i want to get as much out of life as i can, and give as much as i can, to help,maybe to make a difference to someone's life if that is within my capability,recent events have made that need even more clear to me. I'm not sure where I'm going with this or why i bring it up , or if its relevant to want i want to talk about its just in my head right now. What i do want to talk about is something thats been on my mind for ages. I like to be prepared,  I'm not fond of surprises because surprises take control away and i am a bit of a control freak at times. This forum, Our Forum if i can call it that, is here because of two reasons. The guy that created it and keeps it funded and the people that joined it.  Without either, it would not exist, and lets face it one day it won't ( I'm a realist and i talk about things others dont or who are afraid to in other words folk that dont particularly prepare for the inevitable). How many of us visit here regularly ?  How many among us almost depend on the forum as a way of socialising because they are stuck at home and how many of us has it become part of a daily routine to check in and see if they can offer advice or get help with something they are working on or just to have a chat and engage in some banter. The members here are in the thousands and thousands have disappeared over the years many had just a fleeting visit. But there are a good few of us that know each other quite well and visit regularly. I dont know about you but i wouldnt want to lose that communication with you all, in all honesty it has become an important part of that side of my life and helps to feed my passion for all things watches. Some of you may think differently and thats ok, some of may stop and think # what would i do " Without Our Forum " # 
×
×
  • Create New...