Jump to content
  • ×   Pasted as rich text.   Paste as plain text instead

      Only 75 emoji are allowed.

    ×   Your link has been automatically embedded.   Display as a link instead

    ×   Your previous content has been restored.   Clear editor

    ×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Content

    • By Padd
      Hello Everyone,
      Padd here from the UK.
      It all started with a desire to fix a Submariner replica I bought off a lucky lucky man in Pisa, Italy while on a European tour.
      Next thing I know I'm investigating Submariner replicas and building my own, signed by me, using a Seagull ST2130 movement, adventure watch.
      Now I'm hooked, I took inspiration from Marks videos, now I'm happily starting to work on parts of the movement, and have recovered one or two movements where the stem came out, but wouldn't stay back in. I have built a few watches for friends and relations, but now I need to be able to service them when they come back to me.
      I also have a couple of movements that run really badly, so I will be practising on those over the winter weekends. Full repair/servicing kit IS my Christmas present.
      I really want to get one of those ST2130's, serviced and tweaked by me, doing a -------------------------- on my timegrapher. not a -.'-.'''--,'.'.' (and worse) that they do at the moment.
      I wont start to list my watch collection, but it runs from a Casio digital to a Rolex pocket watch with Seikos, Citizens, Omegas and home builds in the mix.
      Must do Mark's course, but I'm afraid I may have already learned 60+% of it already.

    • By PJA
      Just in case, I came across this "Watch-O-Scope" software. To those who have a need for it. Also here is an instructional video how to install. I hope it will help somebody here.
    • By maclerche
      I have gotten hold on a Elma Star vibrograf. Does anyone know if you can still buy paper and carbon for this machine?  
       

    • By SteveT
      I was wondering how do the timegrapher phone app's out there compare to a dedicated bench top machine. I'm guessing it's all down to the piezoelectric pickup? I installed tickoprint on my phone the other day. But to get the full features you need to shell out $30, if you then also have to shell out for a piezoelectric mic, then you are almost at the same price point as a cheap chinese bench top machine!
       
  • Recently Browsing

    No registered users viewing this page.

  • Topics

  • Posts

    • What the problem here is for your question is Mark's video is confusing. Normally when you do a balance staff you would statically poise first then sometimes dynamically poise. If your dynamic poising you use eight pendant positions usually. So in his video he comments for this particular watch he is dynamic poising. Then adjusting to positions is an interesting term or as your question is which positions should you worry about timekeeping in? Basically what you're doing by timing the watch on the timing machine in a variety of positions is your verifying the watch does keep time in those positions.  So for pocket watches dial up and crown up are the most common. For wristwatches I'm attaching what Omega recommends for their watches
    • check each as old hippy said but end shakes on a 3rd wheel allow a lot more play than lets say a balance or escape. you can get away with too much end shake and not loose much amplitude, too little will def not work though and will def result in a very low amp and or stop the movement. train wheels being loose is always better than too tight in my opinion
    • its farfo.com dont put the www. or just google farfo vintage watches ridgewood nj. archer is a memeber on teh Watchuseek forums and is very good esp when it comes to high end watches like omega. he is a certified omega repairer, not many of those around. he uses the same equipment they uses at the omega facilities. 100,000s worth of equipment
    • Try winding through the ratchet wheel, put screwdriver in the wheels slot,turn to wind , should wind full.
    • I made light pressure on the second wheel from underneath and the movement is now running fine. Will check again tomorrow.    
×
×
  • Create New...