Jump to content

Cleaning Balance Cock With Hair Spring


Recommended Posts

Lighter fluid is the safest. You can if so desired clean a complete watch in it. You can leave a hairspring in it for days and it will not harm it. Any thing that has shellac is also safe. You would need a sealed container because it evaporates very quickly.

Link to comment
Share on other sites

Spot on OH. If I have a very dirty balance I will sometimes use a little acetone on it for a short period to be sure that the old oil is all removed and then inspect.   I then use clean Naphtha in the U/S on everything. This method has never failed me.

Link to comment
Share on other sites

Lighter fluid is the safest. You can if so desired clean a complete watch in it. You can leave a hairspring in it for days and it will not harm it. Any thing that has shellac is also safe. You would need a sealed container because it evaporates very quickly.

Can you put a balance with impulse jewel shellacked in the roller table into lighter fluid without the shellac desolating??


Sent from my iPhone using Tapatalk Pro
Link to comment
Share on other sites

6 hours ago, jdrichard said:


Can you put a balance with impulse jewel shellacked in the roller table into lighter fluid without the shellac desolating??


Sent from my iPhone using Tapatalk Pro

Yes you can. Pallets with shellec that hold the stones are also safe. Ronsonol lighter fluid is shallec friendly. At some point I did try a cheaper brand. I found it did not clean as good.

Link to comment
Share on other sites

Yes you can. Pallets with shellec that hold the stones are also safe. Ronsonol lighter fluid is shallec friendly. At some point I did try a cheaper brand. I found it did not clean as good.

Big thanks, I did not know that. I would have dunked the complete balance and all in lighter fluid along time ago. I was Afraid of loosening the jewels. Darn.


Sent from my iPhone using Tapatalk Pro
Link to comment
Share on other sites

Maybe I should use the lighter fluid method for cleaning my balance assemblies. Right now I am using L&R #111 Ammoniated cleaner and L&R#3 rinse in my machine for about 10 minute cycles on clean and rinse. I have noticed some of my balance wheels come out silver instead of brass colored.

I guess I am leaving them in the cleaner too long and it is stripping the finish off. Guessing only.

Will still put jewels in the machine, and try lighter fluid on the balance assys.

Link to comment
Share on other sites

28 minutes ago, gmoodyii said:

Right now I am using L&R #111 Ammoniated cleaner and L&R#3 rinse in my machine for about 10 minute cycles on clean and rinse. I have noticed some of my balance wheels come out silver instead of brass colored.

the L&R cleaner and rinse is the standard of watch repair there's nothing wrong with these. the problem is the ammonia it's what makes the watch come out nice and shiny and bright that's the good aspect.  the bad aspect of ammonia and brass isn't good. If your solution is turning blue in color that's your copper now in the solution and you'll have frosty parts. so to keep the good aspect of the cleaner limit your cleaning time I find five minutes or less works. Then the rinse 10 minutes is fine.

Link to comment
Share on other sites

Thanks for the replies, the L&R cleaner does a great job. I will just shorten the cleaning time.

Been too busy lately to work an any watches, starting to get itchy palms!! Got to get back at the bench!

I have an old aircraft clock that I am going to try and turn a balance staff for, wish me luck!

  • Like 1
Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • although not in this case.  It was the Lugano Convention and its deficiencies that allowed a Swiss court decision in the first place.  This isnt really a Brexit issue at all.  A decision that affects both the EU and the UK should never have been heard in Switzerland. I bet the authorised service centres in the UK are pretty pleased.  It's a massive shame, though; I believe watch owners should be able to choose to have their watch serviced by whoever they trust.
    • Hi guys I think that old hippy is correct, it opens the gates for china to manufacture aftermarket spare parts. considering that they already do work on behalf of the Swiss I guess this decision gives the a little more legitimacy to tool up and I am sure they will take advantage of the situation either with or without the blessing of the Swiss watch industry  Having read about the protectionist machinations of the Swiss in the history of Europe they were the only ones to get fat at everybody else’s expense. I think the outcome could have been guessed at but ,  fair play to Cousins UK for standing up to them.  Now the question,  will everybody boycott Swiss watches and Swatch, no way they will still fill their coffers.  Me I stick with the Japanese once renowned for cheap shitty watches who came good through industrial effort and don’t for get the Russians that most dismiss as low grade crap. Wouldn’t buy a swatch product ever how about you all.? a
    • Hold the crown when in winding position, move the click away from the crown wheel, and then while holding the crown let it slowly unwind. I recollect that you must remove the automatic device bridge first, but maybe I'm wrong. You can first try without removing the automatic device bridge.
    • nevenbekriev- You nailed it with your description of me and my reaction when the clock started ticking again. I am a newbie.  I love the sound and idea of mechanical clocks but the idea of owning one and trying to keep them running has never appealed to me. My wife bought this one and an antique German wall clock.  When I looked into having someone repair them for me, the universal response was "it's really expensive to work on them, you should just replace the movement". So, I had nothing to lose, I started researching them and opened them up. The wife is happy because she hears the sound of the clocks again. But I have gone down the "accuracy" rabbit hole. In the vertical position, the balance wheel was not floating. It was sitting on the bottom of the frame. I adjusted the lower spring collet and got it floating. It easily passed the 270 degree 3 to 5 minute oscillation test. It took 8 minutes for the wheel to completely stop moving.  I put it the unit back in the movement and checked the safety pin. It does not touch the safety roller anywhere in +/-270 degrees rotation from neutral position. But the amplitude of the rotation with the spring fully wound is weak based on what you are saying. It rotates +/-90 degrees from the neutral position.  No, I did not take the movement completely apart.  That seemed way outside my skill set at the time. There is a reason I became an electrical engineer and not a mechanical engineer. I am much more comfortable with moving electrons than tiny moving metal parts. Will I do it in the long run? Anything can happen. I don't seem to be able to let it go.
×
×
  • Create New...