I want to show you my lately restoration project. This time it was a Seiko 7015-8000 with blue dial. Watch came to me in very poor condition. As you can see on photos the case was scratchty, crystal was totaly tarnished with deep scratches. Everywhere was dirt, gunk and mud...yuck. Movement was running and stopping with very low amplitude. After opened the caseback I wasn't suprised - it looked like as case - dirt and signs of wear. Rotor was loose and fall out the case. When I take off the crystall I saw dial which had faded Seiko logo, some scratches and hands which lost their lume.
Next step was strip down the movement - everywhere dirt and dry old oil. Time to cleaning bath
Look at this - it's my temporary balance wheel stand - I suspect that from temporary it will be permanent. It does job well.
After cleaning it's time to assembly movement. Now it looks better - maybe not pristine but clean and shiny. New oil here and there and movement starts to run. Now it's time for bench testing before install it to the case.
Meanwhile I took care of the case, dial and hands. Case got some polishing work - not to much cause I didn't want to loose the sharpness of edges. That is effect:
Dial and hands got new lume - I am not perfect in this work but I still learn to do this. Additional the seconds hand was repainted to orange color. I didn't change the crystall but i just polished it with waterpaper and on the end polish paste. Effect suprissed me. Time for the pleasant work - putting this all pieces together into the watch.
I started new project - Citizen 67-9119. It's seventies chronograph based on 8110A movement. Watch came to me as "fully working in great condition" As you can see there isn't crystal. The one which was here had chip and wasn't set properly in bezel so when i turned the watch it fall on the floor and broke. As you can see dial is in quite good condition, only it needs to be relumed. Hands needs to be repainted and relumed too. Movement works well but it is too speedy ( +3 min/24h). Chrono buttons work properly, only the hour counter stops at "3h" position so I must to take a look here. I striped down the watch and disassembled movement. There was some much oil everywhere so the cleaning is required.
I open this thread to archive works on Citizen 8110A Bullhead. I purchased this watch in poor condition as You can see on the photos.
Cause I have serviced few chronographs in the past I decide to try restore this watch. Maybe is not ractional from the economical aspect but we do this because we love it So let's open it.
Hands are in good condition (required repaint and relume) but the dial has broken legs and tachy scale is faded :/ I think it's really hard to find orginal and there is no gold aftermarket replacement - sad. Look at the movement.
Gosh, what a dirty place It needs good cleaning and oiling.
But the biggest problems are this.
Broken post on main spring bridge and missing rocking bar core and screw in gear train. I need to find replacement.
While I'll be working on movement the case and pushers are send to renew - putting new gold plated coat
Hey everyone, I cant find out how to get this drown off and I've tried everything. The Miyota JS25 movement says PUSH and points to a hole which I've learned means this is where you press to reease the crown but I still can't get the crown out no matter which position the crown is in. I first tried with the crown all the way out then with it halfway in, then all the way in and haven't been able to get it out, please help.
I wish I had more projects to report on but things have really bogged down lately as I continue to bite of more than I can chew. I'm in the middle of three long term projects (the Favre Leuba Bivouac going on year three) and am running short of workbench space. I'm in the middle of changing out the engine in my wife's Mini Cooper too (that's another story but if you own a Mini- be sure and replace the timing chain guides!) and that has really eaten into my "fun time".
I thought I'd bring this one to the board for comments before I'm underwater- it's an old Gallet from the 60's. Do you think it can be salvaged?
We clearly have some water damaged however, the seconds hand will move if the crown is given a little pressure.
Water entered in through the chronograph buttons and the pendant tube. I haven't tried depressing the buttons- I think that would just lead to bits snapping and rust moving about.
I'll need a new stem for sure...
The dial actually looks quite good.
I wonder what it looks like underneath though...
It's not terrible, but it's not great either. Most of the rust damage is concentrated in the keyless works.
There's a bit of damage to the hour recording mechanism...
That's as far as I've gotten thus far. The screw for the Operating Lever is rusted tight and is now being treated with a bit of penetrating oil. Once removed I can pull the second pusher button out and remove the movement from the case. I'll know the full extent of the damage once it's in a pile of bits and pieces.
This is an Excelsior Park EP40-68 movement. I've wanted to work on one of these for quite a while but couldn't afford a proper working piece. Excelsior Park parts are difficult to source though so I may not be able to bring this one back to life.
No registered users viewing this page.
Hi as mentioned by Old Hippy a photo would be advisable so as to asses the level of contamination. as to dissolving varnish, metheylated spirit is what cabinet makers use but be aware that "varnish" as used by cabinet makers is the same product as used to cement in Jewels in the older watches and is still used on some modern watches. As Vinn has mentioned don't wash the jewels out of their settings
I guess its the rarity value also. Roger doesn't make many watches 10 a year I think between him and his apprentice. Still rather have a RS watch than a Rolex any day irrespective of price. I would like to know why Roger picked the Isle of Mann to manufacture his watches and not London.
Indeed. That's the one. They were an unlikely pair, I must say. For both of them I admire the fact that it's not just about keeping time, but keeping time with elegance. Having said that, I knew their watches would be expensive but had no idea just how expensive. Yikes! :-)