Jump to content

Cheap Pegwood


SSTEEL

Recommended Posts

As everyone know, some tools can be somewhat overpriced for what they are, take the Bergeon dial working platform for example.

 

21941361401_e28ff56732_b.jpgBergeon_7053_ by Micky Aldridge, on Flickr

 

BERGEON do sell some great tools of high quality, but the prices are crazy at times, the above dial platform retails at €189 euros.

 

I decided there is no way I would pay that much, and then started looking at how I could make my own, it couldn't be too difficult, right?

 

Here's what I came up with, not pretty, but it works, its a hockey puck, and I drilled lots of small diameter holes in the one side.

 

Hockey puck costs €3 euros delivered.

 

Started life like this.

 

11884909973_804a1ee154.jpgHockey Puck by Micky Aldridge, on Flickr

 

9721568379_5c1289802a_k.jpgMy Bergeon Alternative watch dial platform project by Micky Aldridge, on Flickr

 

After some drilling..

 

21310617573_87a87f19fd_k.jpgUntitled by Micky Aldridge, on Flickr

 

And here's another tool I made for a special case back screw design.

 

14503871614_9f33eed0c8_k.jpgUntitled by Micky Aldridge, on Flickr

 

Other thing I use, instead of Bergeon dial protectors when removing hands, I use a clean ziplock bag..

 

Oh, and a bonus item I made is this microphone dust cover.

 

21645633756_a6cceb3182_k.jpgUntitled by Micky Aldridge, on Flickr

 

Lets see what tools you have made to make your watchmaking more enjoyable without breaking the bank. :)

Edited by SSTEEL
  • Like 5
Link to comment
Share on other sites

Link to comment
Share on other sites

Here's a few.

 

I made this today for tightening the nut when replaing a rotor bearing on an Omega 1120.

 

post-124-0-46403500-1444054981_thumb.jpg

 

post-124-0-77825300-1444055712_thumb.jpg

 

post-124-0-54034900-1444055024_thumb.jpg

 

 

Pair of levers (only one shown) great for hands and especialy snap case backs.

 

post-124-0-40630000-1444055135_thumb.jpg

 

 

Balance tack.

 

post-124-0-50790800-1444055174_thumb.jpg

 

 

Minute hand puller for an Atmos clock.

 

post-124-0-00118100-1444055483_thumb.jpg

 

 

Movement holder for Atmos clock.

 

post-124-0-18894900-1444055539_thumb.jpg

  • Like 7
Link to comment
Share on other sites

Here's a few.

 

I made this today for tightening the nut when replaing a rotor bearing on an Omega 1120.

 

attachicon.gifbearing-tool-1.jpg

 

attachicon.gifbearing-tool-2.jpg

 

attachicon.gifbearing-tool-3.jpg

 

 

Pair of levers (only one shown) great for hands and especialy snap case backs.

 

attachicon.giflever.jpg

 

 

Balance tack.

 

attachicon.giftack.jpg

 

 

Minute hand puller for an Atmos clock.

 

attachicon.gif1.jpg

 

 

Movement holder for Atmos clock.

 

attachicon.gif2.jpg

Balance tack looks great .Tell us/me more?  Want to do one for myself . What material did u use?  Diameter of puck?

Link to comment
Share on other sites

  • 3 weeks later...

Here are some of my "tools"

 

Small tiltable table for one of my lathes

 

141172655514270400_resized.jpg

 

larger tiltable table for lapping

 

141756684327587600_resized.jpg

 

141756684269732000_resized.jpg

 

Lappingmachine for cases

 

142359347537395800_resized.jpg

 

Simple chuck

 

141756684296250400_resized.jpg

 

144113122856684500_resized.jpg

 

"Adapters" for case opener 5700 to open Speedmaster MKII cases, Heuers etc

 

142550996099402200_resized.jpg

 

Stand for oilers, anodized aluminium

 

143103675684819700_resized.jpg

 

Demagitizer

 

143420609075783200_resized.jpg

 

....and much more - I almost like making tools/machines more than refinishing watches!  :D

  • Like 5
Link to comment
Share on other sites

Superb set up there for lapping and case refinishing, love it.  Thanks for sharing, I so cannot wait until I get my own lathe :)

 

Do'nt do it - you will end up making new tools for/with you lathe all the time!   ;)

 

 

Some good stuff there RCD, and a warm welcome to the forum. Your case refinishing kit reminds me that I still have an Omega Chronostop case that I must get around to finishing.

 

Thank you!

 

I must admitt that I usually end up using my small mill when refinishing cases - easy to adjust the angle of the disc, the hight e.t.c. e.t.c. and standard collets makes life easy! :)

 

141995917496339800_resized.jpg

 

A badly beat up Speedy MKII case lapped in the machine above using a 305mm disk with 240 grit paper.

 

144519983028364200_resized.jpg

  • Like 3
Link to comment
Share on other sites

Do'nt do it - you will end up making new tools for/with you lathe all the time!   ;)

 

 

 

Thank you!

 

I must admitt that I usually end up using my small mill when refinishing cases - easy to adjust the angle of the disc, the hight e.t.c. e.t.c. and standard collets makes life easy! :)

 

141995917496339800_resized.jpg

 

A badly beat up Speedy MKII case lapped in the machine above using a 305mm disk with 240 grit paper.

 

144519983028364200_resized.jpg

You have some fantastic tools there your workshop must be of some size. Unfortunately my workshop is a converted small bedroom so such tools are just not possible. Maybe when I get that Lotto up !!!

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.




×
×
  • Create New...