Jump to content

Need Help To Identifying Rotor Problem Before Opening

hokavan

By hokavan
in Watch Repairs Help & Advice

 Share

Recommended Posts

hokavan Watch Enthusiast

hokavan

Posted
Posted (edited)

Hi guys

I've got a like new watch to repair. Its rotor stuck. Hand winding is okay. Because its still has protection pad on the case back so I need some advice identifying the problem before opening.

Thanks

3b672d4c31e0ccf290a3cbcdbf42862e.jpg

Sent from my iPad using Tapatalk

Edited by hokavan
Link to comment
Share on other sites
hokavan Watch Enthusiast

hokavan

Posted
  • Author
Posted

I'd remove the sticker and see if the rotor screw has unscrewed, if you can get a clear view you may be able to see the problem, next most likely cause is a bridge screw come loose and jamming

the rotor.

Max

Could you show me the bridge screw, please

Sent from my iPad using Tapatalk

Link to comment
Share on other sites
ausimax WRT Addict

ausimax

Posted
Posted

hokavan,

 

Is the rotor locked in that position? In other words won't turn?

 

If it is your only option is to undo the centre screw and remove the rotor to se if something is jamming it.

 

I am not familiar with that movement, so I have posted a shot of another movement just to show you the sort of screws that could jamb the rotor if they worked loose.

 

Any of the screws with red arrows could be the culprit.

 

Hopefully others with more knowledge will come to your aid.

post-1709-0-33064600-1454121823.jpg

  • Like 1
Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Geotex
      Any tips to correct a sloppy error?

      By Geotex · Posted

      That's a good idea - shrinking down the nut and wrench size from the old casebook trick!
    • GuyMontag
      Movement holder made with 3D printer

      By GuyMontag · Posted

      I missed this earlier. The dial isn't going into the holder, it should sit proud of it. This is what I am currently using which I print for each different movement.    
    • Neverenoughwatches
      Setting lever spring

      By Neverenoughwatches · Posted

      I didn't think pulling to set position would work harden the spring, in that position it is stressed where the arm starts. By work hardening i meant rapid polishing at that point, a bit like polishing a pivot work hardens as it compresses the steel. I doubt polishing by hand would achieve much in that respect though. Its finished, arm polished up mostly at the join to the bridge's main body. I'm ok with it, the screw holes aren't great as i had to open them up by redrilling and positioning it was difficult, I'm not much use with a loupe, opening up with a file might be a better option for me or i could just use the correct drill size 😅. And the detent is way too deep, i had to guess that with the stem release out of position and sat on top, but i only took one measure and went for it, no slowly slowly catch your monkey 😅. First go I'm happy , well sort of, it works and thats a big thing for me, next one will have a bit more finesse.  Anyone thats interested, after filing, i used a 2000 grade home made diamond  micro file and then 20 micron film, the film is much better than wet and dry, more stable to use and doesn't shed cheap grade grit everywhere , then auto polish on a sponge pad.
    • RichardHarris123
      Setting lever spring

      By RichardHarris123 · Posted

      I'm assuming that every time you set the watch you are work hardening the detent spring, maximum hardening is  where it meets the plate due to maximum deflection.   That's why it snaps there.  The Young's modulus may be the same but after it's reached its maximum yeid strength it breaks.  My mechanic engineering is very rusty, correct me if I'm wrong. 
    • Neverenoughwatches
      Setting lever spring

      By Neverenoughwatches · Posted

      Ah ok yes that makes sense to polish it where the arm starts to form from the body of the bridge, i thought you meant the underneath of all the arm.
×
×
  • Create New...