Jump to content

Which Watch Have You Got Coming In The Mail ? Show Us !!!


SCOTTY

Recommended Posts

On 11/15/2019 at 7:39 PM, JerseyMo said:

ok so the trick to keeping the pallet fork in place is the balance wheel.  By that I mean you back off the brass vconic screw adjacent to the regulator.  This allows the staff to fall on to the plate when updise down .  Than enguge the pallet finger on the jewel.  zip zipp and your off.   okay it still tricky but this will help you alot.....

I wish I had seen this tip last night JerseyMo! I acquired a Timex with this exact movement. The mainspring was fine in mine thankfully, but the thing wouldn't kick off and run. So I made the mistake of disassembling the little bugger. Like you I had a hell of a time getting the escape and pallet to stay in position until I decided to try backing the v-conic balance pivot away. Just like you, that gave me the room I needed to get everything in place. The balance still needed a bit of coaxing to start swinging, but it has been running uninterrupted all night. I took mine apart before I took any pictures of it, I will post some later today.

Link to comment
Share on other sites

I got it back together, and it is running. I adapted JerseyMo's trick, but rather than back off the screw, I supported the balance wheel on a couple of small pips of rodico, to keep it in place, and level,  then laid the fork as per JerseyMo's picture.

This made life a lot easier. Still a bit of a faff, but certainly a lot less of the feeling of attempting to balance a bunch of marbles on an upturned dinner plate.
 

I left it running overnight, (without the hands, in case I need to strip it again). I'll post some pics when I am happy with the way it is running. Thanks for the tip @JerseyMo :thumbsu:

I also cleaned up the unexploded mainspring, so that is now in my parts stash, ready for the next victim.

 

 

Edited by AndyHull
Link to comment
Share on other sites

My new arrival, Avystyle datomatic ! I know nothing about Avystyle but I am thinking it's from the 1970s. It feels overwound and is locked up. Can't let the mainspring off, will have to investigate. Balance swings freely but I can see a rather large loop of hairspring. Would like to get this up and running as cosmetically it's pretty good even though it's ugly.

 

 

IMG_20191117_205243.jpg

IMG_20191117_205343.jpg

IMG_20191117_205317.jpg

IMG_20191117_205059.jpg

IMG_20191117_205044.jpg

  • Like 1
Link to comment
Share on other sites

11 hours ago, AndyHull said:

I'll post some pics when I am happy with the way it is running.

As promised. 1971 Timex Marlin, running.

RIMG0144.thumb.JPG.a70d1b2fb473b4e5865d1b58f35a2e98.JPG

New mainspring, new stem retaining lever, new date spring, new winder rocking bar, new case back, cleaned serviced and running.. after much effort. :blink:

It would have been a lot simpler to swap in a fully working  movement from a later date, but I thought fixing the original was a better solution. Little did I know how much it would fight me.

  • Like 2
Link to comment
Share on other sites

So, I'm flush with money in my PayPal account so I went on a bit of an eBay shopping spree. I picked up 4 watches. 3 are Russian and one is a Seiko. I know it's not very original, but I got the exact same 2 Russian's that Mark  recently featured on his YouTube channel. I've been wanting a couple Russians for awhile and was hesitant to pull the trigger. I liked the ones Mark chose and found 2 identical models for a reasonable price. The third Russian has this really cool embossed/engraved dial that I've never seen on a Russian so I had to grab it.  And finally the Seiko. It is a vintage Bell-Matic with a silver dial in good shape. It has an original bracelet with the tank tread style links. I've had my eye on a mechanical alarm watch and I'm excited for this one.

s-l1600 (4).jpg

s-l1600 (5).jpg

s-l1600 (6).jpg

s-l1600 (7).jpg

Link to comment
Share on other sites

So, I'm flush with money in my PayPal account so I went on a bit of an eBay shopping spree. I picked up 4 watches. 3 are Russian and one is a Seiko. I know it's not very original, but I got the exact same 2 Russian's that Mark  recently featured on his YouTube channel. I've been wanting a couple Russians for awhile and was hesitant to pull the trigger. I liked the ones Mark chose and found 2 identical models for a reasonable price. The third Russian has this really cool embossed/engraved dial that I've never seen on a Russian so I had to grab it.  And finally the Seiko. It is a vintage Bell-Matic with a silver dial in good shape. It has an original bracelet with the tank tread style links. I've had my eye on a mechanical alarm watch and I'm excited for this one.757190795_s-l1600(4).thumb.jpg.0f3805bedd6d3213cd9de48d69bb273b.jpg&key=5733b01922130fb92e46520f65bd1762f2df821924f9c1a4a1e7bbf325ece850

1338761201_s-l1600(5).thumb.jpg.74a7159e0c0a22bf66901fef19d8e0ab.jpg&key=c1a9c26fe55775c6871fc99d757c2bcba803b206812db3baadae1ed256ffc421

1939047567_s-l1600(6).thumb.jpg.038cd20b8df663a4639da909e9e77df8.jpg&key=d279512630851a15bddeb15e1d3830411f7f2b9f0d784e00afa1ecf277fffbdb

660599231_s-l1600(7).jpg.35efb5385ca1b192d4c052c86077e119.jpg&key=6cf6fc57bc2452651a29c9e279e38af1410c6e53f9078fa5630fde8d228394de

 

Nice lot

Don't think the bracelet is a Seiko original. They never used a "one size fits all" bracelet as far as I know.

Should have the coffin link bracelet.

 

 

Link to comment
Share on other sites

I've got another 2 en-route to me. I think I speak for many of us here when I say I'm especially attracted to rare, unusual and sometimes odd timepieces. I have a mid 60's, automatic, Citizen Jet, 25 jewel on it's way. For those that don't know, the jet has a very unique winding rotor where instead of the ubiquitous center pivot attachment, The jet uses a radially machined gear and the entire rotor is free to spin with no mounted pivot point. Finally, There is a vintage "Squadron" race/rally watch on it's way. This one has the pop-out movement housing and what appears to be the original plastic Rally strap. Should be fun! :biggrin:

jet rotor.jpg

jet.jpg

race.jpg

race2.jpg

  • Like 1
Link to comment
Share on other sites

The Bellmatic arrived today and it looks and runs great. It's clean and rings perfectly. I had trouble setting the day/date function at first.. But the Google of everything solved that problem. The only hiccup is the bracelet. Like @ro63rto said, it's a replacement. Someone grafted an old Seiko quartz clasp that was once gold but someone scrubbed the plating off. I'm on the hunt for a proper Seiko coffin link bracelet now.

20191123_203803.jpg

20191123_203921.jpg

20191123_203737.jpg

  • Like 1
Link to comment
Share on other sites

More Timex madness.

1977 Timex Marlin day date.

s-l1600.jpg

It is a bit of a mess, and the case has a slight touch of the chrome pox on the rear, but at least the hands are still in the watch, and hopefully whatever impact caused them to dislodge didn't damage anything vital. I'm only into it for a couple of quid, so if it turns in to a parts watch, so be it.

We will see.

Link to comment
Share on other sites

I tend to shy away from pocket watches, but for some strange reason, this one appealed.
As a result, I am another couple of quid closer to the poor house.

s-l1600.jpg

s-l1600.jpg

Suspicious lack of hairspring, and no hands, but If nothing else it will make a great ornament... who am I kidding its going to get fixed if I can cobble together the bits. There does appear to be a fairly obvious dirt issue too, but I'll wait to see what shows up in the post and let you all know. 

s-l1600.jpg

s-l1600.jpg

Can anyone tell me what the non Latin script inscription says?

 

Edited by AndyHull
  • Like 1
Link to comment
Share on other sites

On 11/25/2019 at 4:23 PM, AndyHull said:

I tend to shy away from pocket watches, but for some strange reason, this one appealed.
As a result, I am another couple of quid closer to the poor house.

s-l1600.jpg

s-l1600.jpg

Suspicious lack of hairspring, and no hands, but If nothing else it will make a great ornament... who am I kidding its going to get fixed if I can cobble together the bits. There does appear to be a fairly obvious dirt issue too, but I'll wait to see what shows up in the post and let you all know. 

s-l1600.jpg

s-l1600.jpg

Can anyone tell me what the non Latin script inscription says?

 

@AndyHull, I like the 3 separate Bridges on the gear train. Reminds me of my Hampden. The engravings are very eye catching. The script under the 15 years part looks possibly Arabic... Where did this come from?

15748141758877402257921711358842.jpg

  • Like 1
Link to comment
Share on other sites

I just purchased my first Swatch branded watch in over 30 years. It's a very sleek, vintage Irony Chronograph. I saw one online over a year ago and finally found one at a price I was happy to pay.:woohoo-jumping-smiley-emoticon:

On a side note, I got to see the world's largest Swatch watch at the 1986 World's Fair in Vancouver BC.

YCS1005_sa040_nvr.jpg

6524499.jpg

  • Like 1
Link to comment
Share on other sites

1 hour ago, FLwatchguy73 said:

The script under the 15 years part looks possibly Arabic... Where did this come from?

I don't know its history, it was an impulse ebay purchase. I'll keep you posted when it arrives. I presume it is 1920s or 1930s. I'll need to look for hands for it too. Similar to this perhaps.

f71c71e2-e50e-4cda-baaf-55149ae29c58.jpg

Best I can tell it is a Langendorf 1725 or 25

Edited by AndyHull
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.




  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • in general this shouldn't be any change. but in general questions like this it be nice to know the specifics of the watch in other words how was it performing before it was cased up and what is it doing now.
    • just as a reminder this watch is a Swatch group product. This will bring up a problem like spare parts and technical information. that I found some links to some information on when I talk about your watch and some of the technical and basically your watch is equivalent to 2834-2 for which I'm attaching the technical sheets. But equivalent does not mean exactly the same you want to do a search on the group for C07 as we discussed this watch before including the technical differences how it's supposed to be regulated and basically because it's watch group there is no parts availability. https://calibercorner.com/eta-caliber-c07-xxx/   https://www.chrono24.com/magazine/eta-movements-from-the-2824-2-to-the-powermatic-80-p_80840/ https://www.watchuseek.com/threads/h-10-movement-details.4636991/ eta CT_2834-2_FDE_481857_15.pdf
    • people be honest.... Swatch is evil for the watchmakers and repairers, BUT not everything in watches from Switzerland is from the Swatch-Group. As far as i know, Selitta got sacked by Swatch as a Movement-Assembler for them and they started to produce Movements in their own Name with slight Modifications. As far as i know, they sell Parts to the Market for their Movements. In most cases, if a ETA-Movement fails, it is a valid Option to replace it with a Selitta Movement, which i consider the Solution for this Mess with the Swatch-Group...... I have no Connection to anybody at Selitta, but being a Swiss-Guy, i still like to have Swiss-Made Watches, but not from the Swatch-Group.   ok ? regards, Ernst
    • Just one more greedy act by Swatch. They started a number of years ago here in the US..cutting off supplies to watchmakers that could build complications that many Swatch houses couldn't even touch. Old school masters who had gone through some of the most prestigious houses in the world. Otto Frei has some statements on their page about it. I tell all my customers to avoid new Swiss watches like the plague,..unless they just want an older one in their collection that still has some parts out on the market, or they have really deep pockets and don't mind waiting months and paying through the nose to get it back. Plenty of others to choose from..IE Seiko,..or other non-swiss brands Even a number of Chinese brands are catching up with the Swiss,..and I think that in time, their actions will be their downfall
    • Yes. If that's not what you are experiencing...start looking for something rubbing. A 1st guess is that one of the hands is rubbing against the hole in the center of the dial. Especially if you now have lower amplitude in face up/ face down positions.
×
×
  • Create New...