Jump to content

Help With stem removal older ETA Quartz movement

gumtape

By gumtape
in Introduce Yourself Here

 Share

Recommended Posts

gumtape New Member

gumtape

Posted
Posted

This is an older 90s ETA quartz movement called 579.005 and I can't figure out how to remove the stem.

I have tried removing both screws along the stem axis and also pushing a pin into that little hole.

Any ideas would be appreciated, thanks. Need to get the movement out to replace the crystal.

PXL_20241101_035458896.jpg

AndyGSi Distinguished Member

AndyGSi

Posted
Posted

Can you post a close up photo of the hole above the black dot with the crown in and out.

You may need a magnifying glass but at whatever position for the crown something
appears in the hole is the position you need to press and release the stem.

gumtape New Member

gumtape

Posted
  • Author
Posted

OK, I'll try that next. The watch is at home and I'm at work right now. Also the hole is REALLY small, like I can barely get a staple in there. Thanks for the tips.

  • 6 months later...
AndyGSi Distinguished Member

AndyGSi

Posted
Posted (edited)
1 hour ago, ConfusedOne said:

I have the exact same dilemma struggling to remove the Stem. Did you get this sorted? How did you do it?

Welcome to the forum

gumtree hasn't been around since shortly after this post.

Can you post the photos requested above.

Edit

Just found one on eBay and spotted the release.

image.png.fbaef0f8a35b2f2257e0bc084df42b20.png

Edited by AndyGSi
  • Like 1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Curare
      Bracelet Extender Sizing

      By Curare · Posted

      Thanks for that Andy, Yes the new bracelet is worth more than the watch itself, Its one I have bought to service and clean-up and on-sell it as a project, look it may sell to someone who has a small wrist, I think I will buy an extender and may-be offer it up with a normal strap as well CJ
    • JohnR725
      Unknown watch movement logo. Very interesting

      By JohnR725 · Posted

      Not always that simple. Typically the only reason we would have any way of identifying a watch is if parts were available at any time and somebody had a parts reference book then they would help you to identify the watches that they have parts or. Unfortunately there are hundreds of thousands of watch movements with no identification and of course typically no parts the classic place were watches would be identified would be under the balance wheel and your pictures don't really show a good view of that. Occasionally I've seen watches marked under one of the plates. They felt very proud of their watch is a very prominent Swiss company and they ask he stamped the bottom of a plate so you have disassembled find it. Then there is the other system the keyless parts make up something called the fingerprint system but you still haven't given us enough information to make use of that. Here's an image showing what a fingerprint system looks like. The PDF is based on the physical book the physical book has sizes of watches these are smaller ladies watches and keyless parts which in the physical book are printed at the actual size of the watch parts. So to identify with the keyless we need in your case diameter measured on the dial side and a good picture of the keyless parts and then you have to hope that this was made within the right time span of the books that have this system on the other hand a lot of times on the dial side they will also put markings. So basically to identify a movement it has to come out of the case and has to be disassembled.
    • AndyGSi
      Bracelet Extender Sizing

      By AndyGSi · Posted

      The strap is a 44Q6JB and hadn't realised how much they'd gone up in price. The used one I've got is very worn but may have other links floating around.
    • mbwatch
      Full plate watch, Suitable tool for adjusting & testing pallet stones?

      By mbwatch · Posted

      @Mercurial is this also a variation of the tool you posted? 
    • Curare
      Bracelet Extender Sizing

      By Curare · Posted

      Thanks Andy, The bracelet is sized very small, around a 14cm wrist. Were would one try to source original links, I guess they wouldn't be cheap if found. The bracelet end links have 4406 B-E stamped on them, is this the Seiko Bracelet code ?? CJ  
×
×
  • Create New...