Jump to content

Stereo Microscope


Recommended Posts

5 hours ago, nickelsilver said:

If you have a workbench that is appropriate for watch work with an eye loupe it will be too high for a microscope.

Indeed.  I have the traditional watchbenches, so I put my microscope on my electronics workbench.  I only use the microscope for fine work (balance, hairspring, etc.) and inspection.

Link to comment
Share on other sites

This guy does make errors and to perfectly honest I was not listening to the magnification quotes but he does show how to achieve a good working space without  purchasing a specific microscope by using a Barlow lens. Wish I had known that before I purchased another scope!!.

The main point he is making is that owning a scope improves your your watch repairs. Parts that you thought were clean are not, hairsprings that you think are breathing perfectly are not etc etc.

Edited by clockboy
  • Like 2
Link to comment
Share on other sites

1 hour ago, clockboy said:

 

The main point he is making is that owning a scope improves your your watch repairs. Parts that you thought were clean are not, hairsprings that you think are breathing perfectly are not etc etc.

Absolutely true. A lot of us say this all the time to beginners that are struggling. # can you actually see what you are doing ? # . Personally i think it SHOULD be one of the first purchases when starting, exactly as Alex stated. We all make mistakes as we are all human, Alex is great at what he does and provides fantastic information for beginners regardless of the odd hiccup.

Link to comment
Share on other sites

8 hours ago, CJMiller said:

This has probably been answered at some point in this thread, but I cant find it.

Anyway, how high is the eyepiece from the surface of the workbench? Will I be able to keep my current workbench and chair, or will I need a lower surface to put the eyepiece at a comfortable height? Thanks.

At a normal table height, it's good. I'm on the short side (5'6" / 1.6m), and I have to sit up straighter than I normally would, but that's probably a good thing. I could also just raise my chair a little...

To answer your other question, it varies depending on what you're doing. I'm currently set up with the 0.5X Barlow for maximum working distance, and 20X eyepiece (non-watchmaking work) but the height changes from there for focusing. I took a tape measure to it just now, and the center of they eyepiece (so eye height) 15 1/4" / 38.7cm.

Also, echoing the comments about his magnification math double counting the eyepieces. 45X is the quoted magnification as configured on the AmScope site with 10X eyepieces. The maximum magnification available with that scope head and without looking around for extra special lenses is 180X (2X Barlow, 20X eyepieces). That's just enough to see some of the larger microfauna (i.e. tardigrades), but not enough to see anything like bacteria. Long story short, it's the wrong tool for the job. A chef's knife where you need a scalpel and vice versa.

Edited by spectre6000
  • Like 1
Link to comment
Share on other sites

Yeah, he certainly blew it when stating the magnification.  I hate it when videos spread bogus info, even if it's an honest mistake.  Makes it so much more confusing for people that are trying to figure this stuff out. 

Rather than hovering in front of the eyepieces, I got some eyecups for mine. Since I also have eyepieces that that have diopter adjustments,  I don't have to wear my glasses when using the scope. Makes it much more comfortable. The eyecups are not expensive, and I find the scope much more comfortable to use this way.

As to bench height, a watchmaker bench at 38 -40 inches is too tall, unless you have a very tall chair or are standing up. I set my adjustable bench at 30", it's lowest setting, and that works OK. I still have to adjust my chair height sometimes, depending on how I have the scope set up. 

Cheers!

  • Like 3
Link to comment
Share on other sites

9 hours ago, HectorLooi said:

No. Zoom magnification range is 0.7 - 4.5. Multiplied by eyepiece magnification of 10X gives 7 - 45.

Heh, true as nuts you’re right. I went to go check my scope (I have the same head as his, just with the double arm). 

6 hours ago, Neverenoughwatches said:

Morning Gert, how are you matey ? Loved your latest video on the drowned seiko.  I will say though i prefer your verbal as opposed to the subtitles. I think your humor shows through better and your accent is great. Keep 'em coming  👍

Evening my man, going good hey. Just running around as it’s payday which suck if it’s your own business haha.

Yeah, I did a poll on my channel a few days ago and 80% of people wanted me yapping so I guess that’s what I’ll do on the next vid (which I’m busy with now). But thank you bud, much appreciated!

 

8 hours ago, Neverenoughwatches said:

I'd  prefer to stay away from amscope as not great reviews,  the one i use is a swift but its the same as the amscope alex does not recommend.

The proper optical Amscopes are great. I’ve had mine for 7 years and no issues hey

13 minutes ago, dadistic said:

Rather than hovering in front of the eyepieces, I got some eyecups for mine. Since I also have eyepieces that that have diopter adjustments,  I don't have to wear my glasses when using the scope. Makes it much more comfortable. The eyecups are not expensive, and I find the scope much more comfortable to use this way.

100% agree on the eye cups, I use them as well. Perfect reference to rest my fore head against in despair when a freshly cleaned cap jewel joins its friends in never-to-be-found-again-ville.

  • Like 1
  • Haha 1
Link to comment
Share on other sites

59 minutes ago, gbyleveldt said:

Evening my man, going good hey. Just running around as it’s payday which suck if it’s your own business haha.

Lol yep tell me about it, mine was yesterday. But now i have a large wad of cash in my back pocket to buy some more cool tools. I do need a better scope though and i am looking towards the one Alex reviewed, I'm just not keen on the amscope brand. But anything besides of good quality is going to empty that back pocket 🤔

1 hour ago, gbyleveldt said:

The proper optical Amscopes are great. I’ve had mine for 7 years and no issues hey

Which model matey ?

Link to comment
Share on other sites

34 minutes ago, gbyleveldt said:

Cheers Gert. This is what i was looking at a while ago, not so sure now,  if they have changed the quality. The working distance is really low compared to mine. I have 250mm through all magnifcations. Only want to change as the x5 mag eyepiece has the same field of view as the x10 around 20mm . The x20 has half that. Not sure why the x5 doesn't give 40mm field of view ?

Link to comment
Share on other sites

2 hours ago, dadistic said:

I hate it when videos spread bogus info, even if it's an honest mistake.  Makes it so much more confusing for people that are trying to figure this stuff out. 

Couldn't agree more! IMO, you do have a moral responsibility to check and double-check before you publish. It drives me nuts not being able to understand something despite giving it time and thought only to later find out it was all wrong. Especially when the information is presented with a tone of authority. If there's one thing I've learnt it is that if someone sounds like they really know what they're talking about, watch out!

  • Like 1
Link to comment
Share on other sites

35 minutes ago, VWatchie said:

Couldn't agree more! IMO, you do have a moral responsibility to check and double-check before you publish. It drives me nuts not being able to understand something despite giving it time and thought only to later find out it was all wrong. Especially when the information is presented with a tone of authority. If there's one thing I've learnt it is that if someone sounds like they really know what they're talking about, watch out!

That makes me perfectly ok then 😆

3 hours ago, dadistic said:

Yeah, he certainly blew it when stating the magnification.  I hate it when videos spread bogus info, even if it's an honest mistake. 

🤔 a little harsh Dave, we all make mistakes mate.  Lets not affect anyone's reputation shall we. 

Link to comment
Share on other sites

We all do. I make plenty, but I try to correct them, and I appreciate it when I'm educated by others.

These videos live forever,  very few are ever fixed.

If someone is watching these for "entertainment", no harm done. If, however, they are like me, and trying to educate themselves, then watching a video that is supposedly for educational purposes and the information that is presented is wrong,  then I get really annoyed. 

I spent a very long time trying to wade through all of the scattered and unhelpful info on these inspection scopes before I finally purchased one.  I was out of the electronics and electronics repair field before they were routinely used and available, so I had no experience with these types of microscopes. 

Trying to figure out how the lenses all worked together to get  a certain level of magnification, field of view, and working distance was not easy. I think I got it right, but it took me *years* before I was ready to pull the trigger. I didn't have, and certainly don't have now, the kind of money where I can afford to make a mistake on an expensive piece of equipment like a good scope. 

Muddying the waters is not helpful

 

  • Like 1
Link to comment
Share on other sites

15 minutes ago, dadistic said:

We all do. I make plenty, but I try to correct them, and I appreciate it when I'm educated by others.

These videos live forever,  very few are ever fixed.

If someone is watching these for "entertainment", no harm done. If, however, they are like me, and trying to educate themselves, then watching a video that is supposedly for educational purposes and the information that is presented is wrong,  then I get really annoyed. 

I spent a very long time trying to wade through all of the scattered and unhelpful info on these inspection scopes before I finally purchased one.  I was out of the electronics and electronics repair field before they were routinely used and available, so I had no experience with these types of microscopes. 

Trying to figure out how the lenses all worked together to get  a certain level of magnification, field of view, and working distance was not easy. I think I got it right, but it took me *years* before I was ready to pull the trigger. I didn't have, and certainly don't have now, the kind of money where I can afford to make a mistake on an expensive piece of equipment like a good scope. 

Muddying the waters is not helpful

 

I get that and you are right choosing a scope is not easy, I'm on with that at the moment and i wont go until i know i have it right. There is some very misleading info and video out there, my first big mistake came from just that. I would just hate to see any harm done when Alex made a simple boo boo. Anyway enough said lets us let this error disappear .

Link to comment
Share on other sites

5 hours ago, Neverenoughwatches said:

Cheers Gert. This is what i was looking at a while ago, not so sure now,  if they have changed the quality. The working distance is really low compared to mine. I have 250mm through all magnifcations. Only want to change as the x5 mag eyepiece has the same field of view as the x10 around 20mm . The x20 has half that. Not sure why the x5 doesn't give 40mm field of view ?

Yeah so mine came with 10x eye pieces as standard, but I did have to add the 0.5x Barlow lens at the bottom to give me the 200mm working distance (a critical item missing from the package I linked earlier). This whole combination gives me 3.5-22.5x in total (thanks @HectorLooifor making me check to make sure) and fully zoomed out I have around 50’ish mm FoV at 200m working distance. I posted pics in this thread a few months ago where I measured it.

  • Like 1
Link to comment
Share on other sites

3 hours ago, gbyleveldt said:

Yeah so mine came with 10x eye pieces as standard, but I did have to add the 0.5x Barlow lens at the bottom to give me the 200mm working distance (a critical item missing from the package I linked earlier). This whole combination gives me 3.5-22.5x in total (thanks @HectorLooifor making me check to make sure) and fully zoomed out I have around 50’ish mm FoV at 200m working distance. I posted pics in this thread a few months ago where I measured it.

That sounds like the ideal working situation. Cheers matey. Unless something else spectacular pops up on ebay at an impossible to turn down price, I'm happy now to along with one like Alex and you use. 

  • Like 1
Link to comment
Share on other sites

2 hours ago, Neverenoughwatches said:

That sounds like the ideal working situation. Cheers matey. Unless something else spectacular pops up on ebay at an impossible to turn down price, I'm happy now to along with one like Alex and you use. 

I think I mentioned it somewhere here, but I've been using this exact setup for my electronics repair business where I work with even smaller parts than you'd find in a typical watch. Having decent working height is critical here. It made my transition to this hobby pretty painless (as far as working under magnification). I've tried various loupes but geesh I think I would've called it quits with this hobby long ago if that was all that was available to me. The biggest benefit is depth perception using a stereo microsocope, something you don't have with a loupe (which refuses to stay in my eye socket in any case).

Edited by gbyleveldt
Link to comment
Share on other sites

1 hour ago, gbyleveldt said:

I think I mentioned it somewhere here, but I've been using this exact setup for my electronics repair business where I work with even smaller parts than you'd find in a typical watch. Having decent working height is critical here. It made my transition to this hobby pretty painless (as far as working under magnification). I've tried various loupes but geesh I think I would've called it quits with this hobby long ago if that was all that was available to me. The biggest benefit is depth perception using a stereo microsocope, something you don't have with a loupe (which refuses to stay in my eye socket in any case).

Same issue with me. A head wire for the loupe ?

Just now, Neverenoughwatches said:

Same issue with me. A head wire for the loupe ?

Two loupes and two wires ?

Link to comment
Share on other sites

9 hours ago, gbyleveldt said:

Haha, I do use that but I can never get it to sit right. Maybe I'm just an idiot, or maybe I'm just trying to look for an excuse hahahaha

Nah you're not an idiot, but you do know at least one , you're talking to him 😃

Edited by Neverenoughwatches
  • Haha 1
Link to comment
Share on other sites

18 hours ago, dadistic said:

the twin boom stand... will give you a good workout when you move it. 

Hear hear!

What are people using for eyecups? I keep thinking about getting some, but getting derailed by (a billion freaking things). They definitely seem like they'd help. @dadisticfor bringing it up most recently.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.




  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • A already know the size movement I have the problem is the dial a had purchased has a dimension 20.6mm wide a want to find a watch case that going to fit the dial perfectly 
    • Hi.  I would like to take issue here regarding battery driven , watches, clocks,etc. I will and do repair these clocks in fact I have sever al in my collection as well as the regular mechanical ones. I have one on my mantle piece over 60 years old tha belonged to my wife’s Aunt,  long gone Iam afraid and it has been cleaned etc and never missed a beat and is accurate. Every one has their preduices as regards Electrical /electronic Horology but I regard it as part of the progress time line of the art of Horology and to be treated as such. Like Darwin’s theory of evolution it evolved.  Two cavemen knocking rocks together and a shard broke off , looking at it he worked out if it was stuck on the end of a stick he would have a spear. Likewise his pal seeing what he was up to picked up a piece  and did the same, now that’s evolution. Some clockmaker decided to build a clock that ran with a battery and no spring to wind up and break, progress and both the mechanical and battery driven clocks evolved, the battery ones got better to the point that if it broke you changed the complete unit. Likewise watches did the same but both can be repaired by people who approach Horology with an open mind without preduice.  We all have our likes and dislikes bu I for one would never dismiss any technology because I don’t like it.   The mobile phone is a good example of modern technology at work as is the automotive industry. There buttons and switches in my car I don’t use because to me they are not nesessary but I still drive the car.
    • I haven't gone through all the reading of what it might be or not. The first thing I would do if nothing obvious stands out is replace the mainspring, you have to start at the source of the power. Nine times out of ten that is the problem.  
    • Haha. You're just in a wicked mood today John 😅
    • Heres my watch of today, a Smith 13'" RY . My missus bought me this for this Valentines day a bargain 14.99 with a reduction, the seller has occasional 20% off offers now and then so it was about 15ish with delivery. I love Smiths and i love bulleye dials, this is my first one. The watch arrived non working as stated and i knew what was inside and what would be against me, but i enjoy a challenge, we dont expect a lot if anything from pin pallet movements. A balance pivot was broken and i didnt have another staff but i did have another RY with a battered dial so i robbed the balance and tweaked it around to make it work apart from that mostly just a good clean and relubrication. Keyless works are pretty rough by design and the crown is a bugger to get in and out with the dial on, the setting lever hits the dial before it releases it, so a little mod is needed to help that along. Major problem was the pins on the lever were quite worn which make the old tg have a snow storm fit. Its a similar read for most pin pallets, these were brass as was the escape wheel. But perseverance is me, i didn't change the pins but i did spend some time dressing and polishing the worn areas which improved the trace a lot with some straightish lines 😅 and a beat error of .5 . Not sure what the lift angle should be on these and i Wasn't in the mood to work it out and who believes timegraphers anyway, but at the default 52° it runs with 260ish full 210 after 24 hours dial down , the verticals rates were pretty much all over place. So lets just put it in it's superlight aluminium case and see what happens. Been wearing it now for 3 weeks and it's consistently losing around 1.5  minutes a week winding each morning i think pretty good for an old pin pallet watch. I just love this dial, thanks wifey heres my Valentine's gift for yer sweetie x
×
×
  • Create New...