Jump to content

Bulk Part Sets?

gpraceman
 Share

Recommended Posts

gpraceman WRT Addict

gpraceman

Posted
  • Author
Posted
Just now, watchweasol said:

The only problem with bulk sets is the accumulation of bits that will never used as they are generic as a rule,  I have one or two I poke about in but never seem to have what I want,  gaskets , crowns, stems, click springs. Etc.

That's what I was trying to determine.  If there are some that are handy or if it is better to just order what is needed at the time.

Link to comment
Share on other sites
JohnR725 Distinguished Member

JohnR725

Posted
Posted

it probably depends upon who is making up the assortment and where did it come from. At work when we were purchasing parts from somewhere the boss purchased an assortment of crowns and when they came there basically all the exact same thing. The definition of assortment seem to be lacking. On the other hand some watchmaker once gave us a bunch of stuff in one of the containers is an assortment of brand new American pocket watch staffs. I really would've liked of known where that came from and get a lot more of them. Because basically every single staff was new and they're all usable. Yes you had to physically look and see what you're looking for some of them were easy to spot like some of the Waltham's because their friction staff's. Or I think I used up all the Hamilton 992B staffs they were very easy to spot. So extremely interesting use will assortment from some place in the past.

So conceivably there are other useful assortments out there but often times they end up being not useful as they just don't have the right sizes or whatever it is you're trying to find.

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Neverenoughwatches
      Setting lever spring

      By Neverenoughwatches · Posted

      I'm not with you there Rich .
    • Disgrace
      Seiko 6309 intermittent stopping of the seconds hand at the same positions

      By Disgrace · Posted

      Hello everybody, sorry for the late reply. Thank you all so much for your help and your tips. I got lucky and found a replacement wheel bridge for cheap which actually ended up being in decent condition. I decided not to do anything about the mainspring barrel pivot since I didn't have the right tools and the barrel didn't have much endshake anyhow. I am happy to report that the watch now runs great, I have regulated it to about +-10/s day which is fine by my standards. The timegrapher result looks decent as well, although beat error is around 0.6ms which could be better I suppose. Amplitude reaches over 230 quite consistently which I'm happy with also. My lighter fluid has also been replaced by balance spring cleaning solution and now the springs don't stick to themselves anymore - who would have thought. I'm super happy with this watch, it might not be worth a whole lot but it's awesome that I could restore it and it makes me wear it with pride. To me it's a genuinely good lucking watch, it'll be my daily driver for a while. Thanks again to everybody for their input! I couldn't have done the repair without your help.   Here are some images for those interested, the bracelet isn't original but I don't really mind:    
    • nevenbekriev
      Is this a 'hack' ?

      By nevenbekriev · Posted

      Balance-hairspring system is oscillator with big Q-factor. When all in the movement is OK, the rate (frequency) is verry close to the own resonant frequency of the balance-hairspring. But in some cases, the movement (with foult) will force the resonator to work on pritty different frequency, sometimes faster, and sometimes slower. When this happens, the amplitude is always weak. So, the first thing to ask is what is the amplitude. If it is more than 180 and the hairspring doesn't touch itself and anything else, then for sure it is 'short'. If the amplitude is weak, then the first thing to do is to understand why and rectify the problem. At this time no point to check timekeeping. But, if one doubts that the hairspring is not correct, then He needs to calcullate the rate of the movement, then to 'vibrate' the balance-hairspring out of the movement and to measure the free oscillations frequency (period) with timer in order to ensure that they comply with the rate. If we have pictures, then it will be easier to tell something about that wheel.
    • Klassiker
      Landeron 248 setting eccentric studs

      By Klassiker · Posted

      So much work has gone into this! Thanks again @Jon. I will go back and check my adjustments from last weekend. A few questions for you, if you don't mind. In the reset position, I can understand the problem if the gap between the hammer and the minute counter heart is too big (slide 77) but what is bad about both hammers being in contact with the cams (slide 76)? I read somewhere that Landeron recommended grease on the runner cam, but the minute counter heart should be dry. Is that so, and why? How many tads in a ligne?
    • BlueHarp
      Difference between AS 1686 and ST 1686

      By BlueHarp · Posted

      Many thanks for your replies!
×
×
  • Create New...