Jump to content

Croton with an ETA 2472


Razz

Recommended Posts

My latest aquisition. Dial is pretty subtle but decent. Hands were off. Non running. Description on the lot did not have info on the movement.  20 to 30 minutes to remove the dial and put back on with reattached hands. Messed around with the automatic winding and fiddled with it until a very low beat on the balance for about 20 to 30 seconds. So another project to step up a level to an automatic with calendar. Will need to get the lube for the automatic gears though first.1702834031_DSCN51672.thumb.JPG.585c9bc04bedca3688ef035ba6e8196f.JPG500568425_DSCN51682.thumb.JPG.4ef3baa6ae790a9f921a1231f01bfbf5.JPG1150977894_DSCN51692.thumb.JPG.167c4a49bc0ea9faf7348ad2ccef5ae0.JPG1305144513_DSCN51702.thumb.JPG.b914e4222bbf3b6345102876ec517bd8.JPG2114352391_DSCN51712.thumb.JPG.d484c046628794865be6a16f3cbcbf03.JPG

  • Like 1
Link to comment
Share on other sites

  • 2 weeks later...

Great movement, I have one on my wrist at the moment 😄 make sure to check out this walkthrough if you haven't already: 

 

By the way, mine was also a non-runner when I got it. Turned out to be too little end-shake on the balance. The lower (mainplate) endstone assembly for the balance was quite easy to shim. Not sure if this is a common "fault" with these movements, but I'd suggest you check the endshake on the balance first. Try loosening the balance cock screw a little and see if it kicks into life.

  • Like 2
Link to comment
Share on other sites

4 hours ago, fellerts said:
4 hours ago, fellerts said:

The lower (mainplate) endstone assembly for the balance was quite easy to shim.

Do you mean that you made the cap jewel thinner? Maybe not. Anyway, I'd really like to hear more about it!

Link to comment
Share on other sites

16 hours ago, VWatchie said:

Do you mean that you made the cap jewel thinner? Maybe not. Anyway, I'd really like to hear more about it!

Oh no, that would be way outside my comfort zone! I simply unscrewed the disk that holds the cap jewel assembly and shimmed it with a couple pieces of thin foil. Shimming the balance cock would probably have worked as well, but I believe it would have been more difficult due to its geometry. Side-note: Do you know why the lower assembly is held in place by a disk such as this?

image.png.bcfa8d659f4d7490bed9c7268cefb3d5.png

The leading theory is that the balance was replaced at some point, and that the new balance staff was slightly longer than the original one, but it's hard to be sure. Anyway the movement runs with ridiculous amplitude now - well in excess of 330 degrees DU/DD, and it does knock a bit at full wind when I move my arm too much. Maybe someone replaced its spring with a slightly stronger one to combat the binding balance? I should inspect the mainspring again... one day! There are too many projects on my bench.

  • Like 2
Link to comment
Share on other sites

20 hours ago, fellerts said:

I simply unscrewed the disk that holds the cap jewel assembly and shimmed it with a couple pieces of thin foil

That's very interesting, thanks, and reminds me very much of the Russian approach (Vostok, Raketa, Poljot, etc.) where you'll most often find one or two shims under the balance cock. I would have thought thin foil (I assume you mean aluminium foil!?) to be too tick, but perhaps it's an ideal material. Got so curious I'll measure a bit of aluminium foil right now. Back in a minute...

IMG_0001.thumb.JPG.c8021e1dea806587c5cb2b778c33d91e.JPG

This is the aluminium foil I found in my kitchen drawer and it's 1/100 mm. So, pretty ideal I'd say. One or two shims would in most cases, I believe, be enough to make the necessary adjustment.

20 hours ago, fellerts said:

Do you know why the lower assembly is held in place by a disk such as this?

I'm afraid I have no idea.

20 hours ago, fellerts said:

Anyway the movement runs with ridiculous amplitude now - well in excess of 330 degrees DU/DD, and it does knock a bit at full wind when I move my arm too much. Maybe someone replaced its spring with a slightly stronger one to combat the binding balance? I should inspect the mainspring again...

Or, perhaps, oil the pallet fork jewels with a bit of thick oil (HP-1300)?!

  • Like 2
Link to comment
Share on other sites

4 hours ago, VWatchie said:

the Russian approach (Vostok, Raketa, Poljot, etc.) where you'll most often find one or two shims under the balance cock.

I've heard that as well, though I still haven't worked on anything Russian yet.

 

4 hours ago, VWatchie said:

This is the aluminium foil I found in my kitchen drawer and it's 1/100 mm. So, pretty ideal I'd say. One or two shims would in most cases, I believe, be enough to make the necessary adjustment.

Jealous of your micrometer there... And yes, I used two tiny strips of basic aluminium foil for this.

 

4 hours ago, VWatchie said:

Or, perhaps, oil the pallet fork jewels with a bit of thick oil (HP-1300)?!

I did play around with adding some D5 to the pivots which seems to reduce amplitude by around 30 degrees after a short test. This might be a viable solution, but I'll have to let it run for a week or so to be sure.

  • Like 1
Link to comment
Share on other sites

  • 4 weeks later...
On 4/14/2023 at 6:39 AM, fellerts said:

Great movement, I have one on my wrist at the moment 😄 make sure to check out this walkthrough if you haven't already: 

 

By the way, mine was also a non-runner when I got it. Turned out to be too little end-shake on the balance. The lower (mainplate) endstone assembly for the balance was quite easy to shim. Not sure if this is a common "fault" with these movements, but I'd suggest you check the endshake on the balance first. Try loosening the balance cock screw a little and see if it kicks into life.

I tried to loosen the balance cock screw a bit without much success. So decided to clean and oil the balance jewels to see if that would help. I opened the balance cock incabloc spring easy enough and got the end stone  jewel and chaton out okay and put in an acetone rinse. I then tried to get the end stone off the chaton and it was stuck! I tried soaking over night and still would not come apart. I finally used a new balance pivot to push the end stone off to clean and oil and put back together. Had to repeat the process for the end stone and chaton on the plate under the dial. I think with these 2 now a little more flexible under the spring and not jammed into the chaton this gave a little endshake and runs great now.

With an all SS case with drilled lugs, original dial and hands this looks pretty good, without doing much more than an ultrasonic cleaning of the case.

I wonder what the CHP is about. I was thinking maybe California Highway Patrol...lol. maybe ponch (Erik Estrada) wore it during filming of the TV show. Anyways another look at it.906907024_20230510_1948152.thumb.jpg.31a5f6cc43e188e665b1ad600cce1e7d.jpg233118540_20230510_1948272.thumb.jpg.1603fd7c89fc5ced256a3372cfda92a4.jpg1481918069_20230510_1955562.thumb.jpg.6ef2a2dde96d559df78b6352bfcdcf4c.jpg

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Have you ever seen grease spread?  I use Molykote DX on the keyless, cannon pinion, etc and cannot imagine it spreading. Similarly, HP1300 should not be a problem, as long as you don't splash too much about.  9010 does like to travel though. I've recently re-serviced a couple of my watches I first serviced about 5 years ago. I was a bit too liberal with the oil and grease back then, but it hasn't spread everywhere. I only epilame on balance cap stones, escape wheel and pallet stones (and auto wheels if they need it).   If you use it all over, the oil might bead-up and travel even further - think of using RainX on your car windows.
    • Polish it where the old part cracked as well. Get rid of the stress-raisers.
    • Sounds great! And yes, I would use grease for the keyless as well although treating the parts with epilame would make the grease less likely to spread in the long run. Not critical but won’t hurt. My current strategy is to epilame treat all parts getting in contact with oil or grease.
    • Hello everyone, for what it's worth, here is my approach: 1. Escape wheel submerged in Epilame, then dried quickly with a hairdryer. Then the final tip of the pivots are cleaned by poking into pithwood. The logic being that the Epilame is removed at the intended contact point (to avoid any residue that may mix with the oil), but remains in the areas where oil is not supposed to spread to (further down the pivot towards the wheel). The escape wheel teeth also benefit from having Epilame to keep the 9415 in place.  2. I use a syringe to treat only the pallet stones. I suspend the pallet fork with some Rodico so that the stones hang downwards. I notably use a rather thick needle where a drop WON'T form, but rather where the Epilame liquid stays in the needle tip, which I then dip into the pallet stones. It requires some practice to get the right amount of Epilame into the needle tip, but it works for me now. This way, no drop will "jump" onto the pallet fork and potentially go all the way to the pivots.  3. I let the movement run for a few minutes without lubricating the pallet stones... to scrape off the Epilame in the intended contact "channel". Then I remove the balance again and lubricate the exit pallet stone with 3-4 successive drops. See the "channel" that forms on the pallet stone in the picture -- not so easy to see, but it's visible.       I am conflicted about the use of Epliame in balance jewel settings. My impression is that the two jewels sufficiently suspend the oil (even 9010). Apparently Rolex recommends NOT to use Epliame there (heard from a former Rolex service center watchmaker), as it could cause additional wear. Apart from that, I follow specific instructions where I can find them. E.g. the infamous Rolex reverser wheels or sometimes (parts of) the seconds wheel. Exception: I'm currently servicing an Eta 2824 and will probably ignore the service sheet that recommends treating the whole keyless works with Epilame and then using HP1300... I'll skip the Epilame and use 9504 grease.        
    • I'm going to give this a try today/tomorrow on my UTC33/Seiko 66, thanks!
×
×
  • Create New...