Jump to content

Cheap Dh


Recommended Posts

Found a Silvana DH on eBay the other day in some obscure ex Russian state,and as I've wanted a German ww2 military watch for some time I thought I would take a chance,it was listed as not working and from the pictures I could see it was without its crown,post-849-0-55608100-1437598350_thumb.jpg on arrival I had quite a job removing the case back,and by the look of the scratches others had tried too.post-849-0-47940600-1437599285_thumb.jpg I don't think it had been removed in a long time and when removed I was pleased to find the movement complete albeit very dirty,post-849-0-94183900-1437599519_thumb.jpgwater had got in past the stem at some time and the dial was very dirty and moldy and the hands rusty,post-849-0-97326500-1437599768_thumb.jpg and the keyless work rusted solid,post-849-0-44510500-1437599916_thumb.jpg I stripped the watch down and all parts except keyless work were ok so set about cleaning.as I don't have a cleaning machine all was done by hand and I'm still learning as I go! In the areas on the bridges where the corrosion was worse the silver finish is worn away but that aside when reassembled the watch ran fine, post-849-0-88820500-1437600695_thumb.jpgpost-849-0-10811800-1437600861_thumb.jpg I then set about the dial with much trepidation,but after a gentle start found the dial to be very sound so a little more time and effort got a good result.post-849-0-75227200-1437601140_thumb.jpg before.post-849-0-28315700-1437601255_thumb.jpgand after.now the watch is reassembled and running fine but still needs the case repaired and rechromed and some more pics taken so more to follow,but as this watch only cost £18 with £5 postage I think I've done ok.

  • Like 4
Link to comment
Share on other sites

Hi Nige, you've done exceedingly well to get it running and looking as good as it is. I would never have believed you could have salvaged the dial, what method did you use to clean it? The case is going to be a bit of a challenge too. You will have to silver solder a new bar in place before plating. I'm keen to see the finished result.

I hope our oracle Will chimes in with some history information.

  • Like 1
Link to comment
Share on other sites

That's a great job, Nige - and, when it's finished completely, you'll have a watch worth many, many times what you paid for it. Those D-H watches from WW2 are much sought after. They're more or less the equivalent of our own A.T.P. or W.W.W. military watches - but possibly quite a bit rarer. Don't forget to show us the final product. How are the hands faring?

Link to comment
Share on other sites

Contrary to what I said earlier would you not be better to just have a new bar fitted to the case and leave it as is? You will wipe out the historic patina and probably de-value the watch in the process if you refinish it.

Link to comment
Share on other sites

Contrary to what I said earlier would you not be better to just have a new bar fitted to the case and leave it as is? You will wipe out the historic patina and probably de-value the watch in the process if you refinish it.

I think, on the whole, I'm with Geo on this one. I think it's perfectly acceptable to polish up and refinish a watch case with no actual historical value. WW1 and WW2 watches, in my opinion, have a story to tell - which is written in their physical condition, as it were, and I've never messed with mine. "Messed`' would be the word that would describe my efforts!

  • Like 1
Link to comment
Share on other sites

Hi all sorry took so long to reply,in answer to your question Geo,I cleaned the dial with "artists picture cleaner" from Windsor and Newton it's for cleaning old oil paintings as I paint a bit I came across it in an art shop and used it to clean a moon face dial before I restored it,the method I use is with a cotton bud and gently apply in a circular motion in a small area at a time,obviously check it first but I've done a few and had no problems, and as to the hands Will,they have come up ok but I've not gone to mad,I think your both right about the case and I won't rechrome it,

post-849-0-54295400-1437733934_thumb.jpg

Link to comment
Share on other sites

Thanks for your kind words guys,all I need to do now then is fit a new bar,I don't know how silver solder is done so ill have to get my brother to do it,he's quite stacked out with work so i,'ll have to wait my turn,I'm looking forward to wearing it.

Link to comment
Share on other sites

First post on here, amazed it has taken me so long to find this forum. I will do a proper intro later, but just wanted to add a plus one recomendation for Adam Philips. Used him for the first time last week on a Breitling 181 case, very badly pitted and lost most of its chrome. Came back looking amazing and original not like it had been re-chromed! Will put a post covering that particular restoration up soon.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • although not in this case.  It was the Lugano Convention and its deficiencies that allowed a Swiss court decision in the first place.  This isnt really a Brexit issue at all.  A decision that affects both the EU and the UK should never have been heard in Switzerland. I bet the authorised service centres in the UK are pretty pleased.  It's a massive shame, though; I believe watch owners should be able to choose to have their watch serviced by whoever they trust.
    • Hi guys I think that old hippy is correct, it opens the gates for china to manufacture aftermarket spare parts. considering that they already do work on behalf of the Swiss I guess this decision gives the a little more legitimacy to tool up and I am sure they will take advantage of the situation either with or without the blessing of the Swiss watch industry  Having read about the protectionist machinations of the Swiss in the history of Europe they were the only ones to get fat at everybody else’s expense. I think the outcome could have been guessed at but ,  fair play to Cousins UK for standing up to them.  Now the question,  will everybody boycott Swiss watches and Swatch, no way they will still fill their coffers.  Me I stick with the Japanese once renowned for cheap shitty watches who came good through industrial effort and don’t for get the Russians that most dismiss as low grade crap. Wouldn’t buy a swatch product ever how about you all.? a
    • Hold the crown when in winding position, move the click away from the crown wheel, and then while holding the crown let it slowly unwind. I recollect that you must remove the automatic device bridge first, but maybe I'm wrong. You can first try without removing the automatic device bridge.
    • nevenbekriev- You nailed it with your description of me and my reaction when the clock started ticking again. I am a newbie.  I love the sound and idea of mechanical clocks but the idea of owning one and trying to keep them running has never appealed to me. My wife bought this one and an antique German wall clock.  When I looked into having someone repair them for me, the universal response was "it's really expensive to work on them, you should just replace the movement". So, I had nothing to lose, I started researching them and opened them up. The wife is happy because she hears the sound of the clocks again. But I have gone down the "accuracy" rabbit hole. In the vertical position, the balance wheel was not floating. It was sitting on the bottom of the frame. I adjusted the lower spring collet and got it floating. It easily passed the 270 degree 3 to 5 minute oscillation test. It took 8 minutes for the wheel to completely stop moving.  I put it the unit back in the movement and checked the safety pin. It does not touch the safety roller anywhere in +/-270 degrees rotation from neutral position. But the amplitude of the rotation with the spring fully wound is weak based on what you are saying. It rotates +/-90 degrees from the neutral position.  No, I did not take the movement completely apart.  That seemed way outside my skill set at the time. There is a reason I became an electrical engineer and not a mechanical engineer. I am much more comfortable with moving electrons than tiny moving metal parts. Will I do it in the long run? Anything can happen. I don't seem to be able to let it go.
×
×
  • Create New...