Jump to content

How to center a hairspring


Recommended Posts

40 minutes ago, DaveL said:

Thanks to all I will give it a go, a flat hairspring

looks fine until the stud is installed in the cock

Thats the two fixed points of contact of the balance cock holding the spring. The top staff pivot ( indirectly via the collet ) and the stud. 

2 minutes ago, JohnR725 said:

it would be helpful to have a picture of the other side of the balance wheel without the bridge attached so we can see how the terminal curve looks.

Are you thinking maybe someone has tried to straighen an overcoil into a flat spring by mistake ? The terminal curve looks quite beat up John.

Link to comment
Share on other sites

7 hours ago, Neverenoughwatches said:

Are you thinking maybe someone has tried to straighen an overcoil into a flat spring by mistake ?

actually what I'm thinking is typically on Elgin watch especially older is it's an over coil. It be easy to tell if we had the other side view or if we had the serial number of the watch we could look that up. It just doesn't quite look right for a flat hairspring. but it still could be a flat hairspring it be easy enough to tell from the other side. Plus it's easy to remove from the balance bridge just loosen up the stud screw and push it out and it's easy enough to get it back.

Link to comment
Share on other sites

20 minutes ago, DaveL said:

Ok on further inspection it appears to be a over coi

typically with American pocket watches that's what you're going to find and that's what it looked like.

I enhanced your photo a little bit it appears to be your missing your over coil and yes the stud isn't quite where it's supposed to be. Typically things like this happen if somebody lifts up the balance bridge in the balance stays behind the hairspring gets stretched of what looks like the rest they hairspring is relatively flat.

Ideally when you're practicing with hairsprings it be nice if you had some practice hairsprings to practice with. in other words is nice to have something that you can break because you probably break it before you get good at fixing hairsprings. Then ideally for something like this it be nice to find an example watch the look at how it's over coil is formed because yours is missing.

hairspring problems.JPG

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • people be honest.... Swatch is evil for the watchmakers and repairers, BUT not everything in watches from Switzerland is from the Swatch-Group. As far as i know, Selitta got sacked by Swatch as a Movement-Assembler for them and they started to produce Movements in their own Name with slight Modifications. As far as i know, they sell Parts to the Market for their Movements. In most cases, if a ETA-Movement fails, it is a valid Option to replace it with a Selitta Movement, which i consider the Solution for this Mess with the Swatch-Group...... I have no Connection to anybody at Selitta, but being a Swiss-Guy, i still like to have Swiss-Made Watches, but not from the Swatch-Group.   ok ? regards, Ernst
    • Just one more greedy act by Swatch. They started a number of years ago here in the US..cutting off supplies to watchmakers that could build complications that many Swatch houses couldn't even touch. Old school masters who had gone through some of the most prestigious houses in the world. Otto Frei has some statements on their page about it. I tell all my customers to avoid new Swiss watches like the plague,..unless they just want an older one in their collection that still has some parts out on the market, or they have really deep pockets and don't mind waiting months and paying through the nose to get it back. Plenty of others to choose from..IE Seiko,..or other non-swiss brands Even a number of Chinese brands are catching up with the Swiss,..and I think that in time, their actions will be their downfall
    • Yes. If that's not what you are experiencing...start looking for something rubbing. A 1st guess is that one of the hands is rubbing against the hole in the center of the dial. Especially if you now have lower amplitude in face up/ face down positions.
    • Once a movement has the dial and hands put back and it is recased, would you expect the assembled watch to have the same amplitude as when the movement is in a movement holder and is without hands and dial? Thanks
    • C07641+ not sure what the "+" is for after the last digit.
×
×
  • Create New...