Jump to content

Unitas 431 Ratchet Wheel Screw - LH threaded?

Watchoutnow
 Share

Recommended Posts

Watchoutnow Member

Watchoutnow

Posted
Posted

Hi, I just managed to break the head off a ratchet wheel screw (not the crown wheel screw which is LH threaded) on a Unitas 431 in a Waltham 25 jewel railroad watch. I assumed it was RH threaded and was frozen (which it might well have been for all I know presently). I had previously successfully worked on a Unitas 6431/6445 variant and didn't have any problem with the ratchet wheel screw so I was a little too sure of myself with this one. 

I did source a new arbor for the 431 but I can't find a new loose screw. I don't have a screw machine (I might ask my jeweler to make one).  Does anyone have any experience with this movement? I'm under the naive impression that there can't be much difference between the barrel/arbor/ ratchet in Unitas family 431 cum 6431 cum 6445 cum 6497. Is this screw indeed LH threaded? Will a ratchet wheel screw from a 6497 fit a 431 arbor? I'm waiting for delivery of the arbor before I can test it.

I assembled the movement and I was successful in restoring it with the exception of the arbor/screw. I was able to wind the watch to test it without the screw but obviously this is only temporary.

I did check Dr Ranfif's webpage and he cautions that the 431 might have a LH thread, but he also says this about the 6431/6445 which I didn't experience.

If anyone has any information I would appreciate it. I'll publish my findings in the hope it might help someone else...J.

Link to comment
Share on other sites
JohnR725 Distinguished Member

JohnR725

Posted
Posted
13 hours ago, Watchoutnow said:

a ratchet wheel screw

I have a link to a parts listing where we have a mystery. So they list the ratchet wheel screw not sure if we can get one but which one did you want to left-handed or the right-handed one? This is one of the problems of watches that have been made over time you can end up with variations. Like I see this for different balance completes for this watch that's always a clue of made over time with variations.

then when you figure out which screw you need you click on it and give your cross referenced all the ones that have the same screw type. You can also take the suitable part number and go to their home page enter it in and see if they have one

http://cgi.julesborel.com/cgi-bin/matcgi2?ref=UT_431

http://www.ranfft.de/cgi-bin/bidfun-db.cgi?10&ranfft&0&2uswk&Unitas_431

 

Link to comment
Share on other sites
Watchoutnow Member

Watchoutnow

Posted
  • Author
Posted

Thanks, I see the link in Jules Borel but can't seem to be able to order either part. I have an arbor coming but I don't know if it is a RH or LH. What baffles me is that the mainspring is a RH winder, which means that turning the ratchet screw to the left would put resistance against the click pawl which would allow me to unscrew it. If I turned it to the right it would only wind the watch, so how could it be a LH screw? Would I have to have been holding the winding stem crown to put resistance in the RH direction? This seems strange. ..J.

 

Link to comment
Share on other sites
Watchoutnow Member

Watchoutnow

Posted
  • Author
Posted (edited)

I also see in JB's index that the UT 431 RH screw 5415/607 cross-references to the ratchet wheel screw on a UT 6497 which are easily had. So, maybe I'll get lucky and receive a RH arbor that matches a 6497 ratchet screw. I also searched this pn on Otto Frei's parts look up and it too references the UT 6497. Maybe the arbor for a 6497 might also be compatible, something else I could try. 

Otherwise I'll need to find a 5415/375LH screw, or have a screw made or have the arbor I have with the broken screw machined out and re tapped to fit an available screw...J.

Edited by Watchoutnow
wrong lh screw pn
Link to comment
Share on other sites
JohnR725 Distinguished Member

JohnR725

Posted
Posted
6 hours ago, Watchoutnow said:

have a screw made or have the arbor

you must live in a different part of the planets and I do because getting a custom screw made would cost more than the whole watch. I don't even know actually who would make custom screws. Typically when I need a screw I open up my box of miscellaneous screws and go through all the little containers so I find something that works. Or I have physical material houses I could send the watch down and see what they have or see if they would even have the part this is one of the minor catches to online material houses they don't actually list everything. So if you had the luxury of living in a location that had a physical material house you could ask them or even some of the online ones you can ask if they have the part

6 hours ago, Watchoutnow said:

Maybe the arbor for a 6497 might also be compatible, something else I could try.

if you click on the arbor for your watch at the link I gave you it gives you the cross references and the 6497 is not a cross reference part. So while the screw might fit the arbor will notplus of course the barrel does not fit either.

Then a course is back to eBay to see if can find a broken movement. Then this is also the probably working on older watches is defined spare parts. Or for that matter find you spare parts for just about any watch can be a challenge depends upon what it is

Link to comment
Share on other sites
Watchoutnow Member

Watchoutnow

Posted
  • Author
Posted

I resolved my problem. I was able to back out the broken screw in the arbor and confirmed that it was indeed LH threaded. I found a LH screw for it in a box of mixed ratchet wheel screws. I also received the replacement arbor I ordered and found that it is indeed RH threaded. I found the matching screw for this in the same box of screws. I decided to install the RH arbor instead of the original LH arbor in order to spare some future watchmaker of the same frustration. I would think that since this movement was a mass produced item that the screw couldn't be that hard to find.

I even found a match for the missing dial feet screws in another box of mixed df screws. CK has nice mixed lots of assorted screws for various functions at a very reasonable price. 

I still wish I had a mini lathe and a set of screw dies. I'm a retired engineer and it was too easy to ask someone at work to make something every time it was need...so that's the "parts of the planets" I'm from.

I didn't try a ratchet wheel screw from a 6497 to test to see if that was compatible but I may if I get a loose one, I just didn't feel like opening up the 6497 I have cased. The arbor and barrel is much smaller but I did test the ratchet wheel and the square matches the arbor but the wheel diameter is also much smaller.

I hope this helps someone else someday...J.

Link to comment
Share on other sites
LittleWatchShop Distinguished Member

LittleWatchShop

Posted
Posted
7 minutes ago, Watchoutnow said:

I resolved my problem. I was able to back out the broken screw in the arbor and confirmed that it was indeed LH threaded. I found a LH screw for it in a box of mixed ratchet wheel screws. I also received the replacement arbor I ordered and found that it is indeed RH threaded. I found the matching screw for this in the same box of screws. I decided to install the RH arbor instead of the original LH arbor in order to spare some future watchmaker of the same frustration. I would think that since this movement was a mass produced item that the screw couldn't be that hard to find.

I even found a match for the missing dial feet screws in another box of mixed df screws. CK has nice mixed lots of assorted screws for various functions at a very reasonable price. 

I still wish I had a mini lathe and a set of screw dies. I'm a retired engineer and it was too easy to ask someone at work to make something every time it was need...so that's the "parts of the planets" I'm from.

I didn't try a ratchet wheel screw from a 6497 to test to see if that was compatible but I may if I get a loose one, I just didn't feel like opening up the 6497 I have cased. The arbor and barrel is much smaller but I did test the ratchet wheel and the square matches the arbor but the wheel diameter is also much smaller.

I hope this helps someone else someday...J.

Also a retired engineer...electrical. I love my lathes. Recently re-pivoted a center wheel. This morning I made a setting lever screw for a member of this forum.

  • Like 1
Link to comment
Share on other sites
JohnR725 Distinguished Member

JohnR725

Posted
Posted

as we like to dream about making things here is a book that talks about making things. Making things by machinery unfortunately they don't break each machine down to its components which would be rather nice. I rather like page 48 the steps of making a balance staff by machinery.

https://archive.org/details/evolutionofautom00mars

 

  • Like 3
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Jon
      Introducing myself

      By Jon · Posted

      Hi there  
    • Jon
      Movement inserted from crytal side

      By Jon · Posted

      Put the movement in a movement holder and it will be supported as you push down on the setting lever post to release the winding stem. Make sure the post is over the shoulder of the movement holder so what you are pressing down on is supported. As a general rule, hold the movement and not the movement holder. Replace the hands when the movement isn't in the case and support the centre jewel (if it has one) on a hard surface or staking block when replacing the hands to stop the jewel accidentally moving or even coming out. A dedicated movement holder with a central jewel support is even better, but pricey
    • JohnR725
      Main spring

      By JohnR725 · Posted

      It might help us if we knew which watch like model number.
    • Zedster
      Movement inserted from crytal side

      By Zedster · Posted

      Hi, guys I have a bit of a predicament and hopefully, somebody can advise. I'm working on a Roamer MST 521 where the movement is extracted from the crystal side. I'm now at the final hurdle where I need to replace the movement back into its case but I'm not sure of the correct procedure. I still need to fit the hands but that's where the problem lies. If I insert the winding stem to test the hands for correct alignment I will need to turn the movement over to release the stem again it's the spring-loaded type and needs a small bit of force to push down but with the hands fitted, I don't think I can do this on a cushion without causing some damage to the hands and that's the last thing I want to do, this watch has already been a love-hate relationship and I'm so close to boxing this one off which I'm counting as my first major project.  The other option is to case the movement then fit the hands and hope everything is okay. I've already broken the original winding stem but managed to find a replacement, the last one in stock, so I'm a bit reluctant to keep removing it. Any suggestions would be appreciated. 
    • Jon
      Main spring

      By Jon · Posted

      I would go for the dearer spring. You won't need to remove the spring from the carrier ring and then use a mainspring winder to get it into the barrel, for a start. Also that spring is closer to the needed dimensions, especially the length. The length plays a part in the mainsprings strength. If you double the length you will half the force (strength) of the spring and vice-versa. A spring with 20 mm less length would be about 7% shorter, so technically would be 7% more strength, but I find halving this number is closer to real-world findings, so the spring would be about 3 to 4% more strength/force. On a mainspring that ideally kicks out 300 degrees of amplitude, a 3% increase in amplitude would be 309 degrees. Increasing or decreasing the length of the mainspring will affect the power reserve to a greater or lesser degree. It depends how much shorter or longer it is. I've attached a lesson regarding mainsprings, focussing on the size and strength of the spring within the barrel, you might find helpful. Unfortunately it is a PDF converted from a PowerPoint presentation, but only a slide was lost that was originally a video of fitting a mainspring   Lesson 5 The mainspring.pdf
×
×
  • Create New...