Jump to content

Mainspring


Willow

Recommended Posts

 

40 minutes ago, watchweasol said:

Hi Guys  find attached pages from Laurie Pennman (Master clockmaker) and his calculations for the mainspring acommodation as regards to the barrel fitting…

Exactly what @praezis explained 🙂

Edited by Kalanag
  • Like 1
Link to comment
Share on other sites

Hi. As a rule of thumb Iwould say so as the spring needs space to operate. But the actual data for springs in barrels is calculated as Lauri Pennmans formula in his book for exactness and confirmed by Prazeis (Frank) who also came to the same conclusion with his calculations.  So in conclusion Pennman/Prazeis are correct and De Charles theory is just a guide.

  • Like 1
Link to comment
Share on other sites

As promised hear is a photo of the spring in the barrel you can see how tight it is, now the question is when i order a new spring do i get a thinner spring, shorter spring, even a different height spring or all three, thanks for your patience

20230204_122242.jpg

20230204_122253.jpg

Link to comment
Share on other sites

It looks a little long and from the angel of the barrel looks as if it could be a little higher. From what I can recall the springs in these movement are very strong so a little less strength should be fine. Don't have it to high you do not want it rubbing the inside of the barrel cap.  

  • Thanks 1
Link to comment
Share on other sites

6 hours ago, Kalanag said:

As @praezis an Laurie Pennman calculated correctly the rule of thumb should be 1/4 instead of 1/3

I was referring to the guideline for testing if a spring is "set".

 

2 hours ago, Willow said:

As promised hear is a photo of the spring in the barrel you can see how tight it is, now the question is when i order a new spring do i get a thinner spring, shorter spring, even a different height spring or all three, thanks for your patience

The spring looks a little long. I'm wondering if it would be possible to cut off 2 or 3 coils then anneal and reshape the cut end.

But looking at the coil, it should be able to take a lot more than "two or three" winds. I think the problem lies elsewhere.

  • Like 1
Link to comment
Share on other sites

I searched my library for mainspring rules.

None of the celebreties mentioned in this thread invented those rules themselves. They were taught it and passed that knowledge in their books.

In fact some old books mention such 1/3 rule while the exact dimensioning of mainsprings was already known and published for a long time. Seems it was a rule of thumb among craftsmen who were more busy with file and lathe than with books.

The rule for a maximum of barrel revolutions that determines the optimal length of a mainspring was published by Rozé in 19th century. Claudius Saunier mentions this in his comprehensive textbook (paragraphs 1211-1216) from 1861. I also found this rule in books from 1902 and 1923. So Mr. de Carle could have known better. 

Nevertheless a watch or clock with a too long mainspring will run its 24 hours and so supporters of the 1/3 rule were contented.

Frank

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • This place has them, cheaper than I saw on ebay and they appear to be a legitimate supplier: https://maddisonsofdurham.co.uk/watch-parts/capacitors/seiko-batteries-capacitors/seiko-capacitor-kinetic-30235mz-tc920s-5m42-5m22-5m23-battery-3023-5mz-3023-5my/?gad_source=1&gclid=CjwKCAjw7-SvBhB6EiwAwYdCASmviGb9G2ZGW3CtcUZBkNgglcgfPKoqnpOzrzruiPtm69f6DX7UGhoCKl4QAvD_BwE There is also a note at the bottom of the page about them being a newer type, with a slightly different part number.  
    • Are we ignoring  that another watch on tg showed similar rate fluctuation. Did I miss any conclusion made on this sigificant  point ?    Springs have high fatigue threshold,   meaning angle of  bend/distortion  has to be very sharp to cause material fatigue .  An evidence to this point is the bend we form at end of terminal curve or the bend at the collet,  are we causing fatigue there? definately not.       
    • Yes, I do have the Seitz pivot gauge which is worth a small fortune these days. Got mine for about £200 which I thought to be crazy expensive at the time, but I've now seen asking prices over twice that. And no, I do not have the scaled pin gauge, but it would be convenient. Let me know if you find them! Anyway, the Seitz pivot gauge is in my opinion not really necessary if you have the JKA Feintaster. It can measure even the very small pivots w/o making any dents. One will have to be a lot more careful when using the Bergeon micrometres.
    • Update. Ran into a winding problem since some desperate previous repair guy had fitted the wrong winding gear. Cousins had one ! Turns out the movement is the slightly different 022 - 18 Looks like the one LH screw fixing for the crown wheel got updated to the two screw style.
    • Didn't you see the impact on your time machine? 🙂 Nobody told me this / or read it in any books but whenever I have a reading like yours one of the first things I check is the plate screws and in the majority of the cases the readings get better after tightening them, smoothing out your curves. If they are tighten enough it makes no sense to tighten them more as it brings no benefit but excessive force might cause the screwheads to brake off. You have the feel for it after a while. I have seen cases where the plate screws were not tight on purpose just to sort out some end shake issues but needless to say that's not the right way to go. Plate screws must be tight enough  just like the critical screws in automotive otherwise you screw up the whole movement in my opinion. I must stress that this is only my own opinion and i am just a hobbyist. 
×
×
  • Create New...