Jump to content

c1970 Smiths (EB8800)

GDub

By GDub
in Introduce Yourself Here

 Share

Recommended Posts

GDub New Member

GDub

Posted
Posted

Hi Guys,

               Just a quick shout out for advice/suggestions, I am very much a newby to watch making and currently completing Marks Level 3 training course, this said, I confidently acquired a vintage Smiths mechanical wind watch, I performed a full strip down, clean and lubrication re-build, new crystal mainspring case polish etc. all sounds good up to now, however, I now find that the watch is erratic on the timegrapher, one minute 20-30 s/d and 1.5 beat error, as soon as you change the crown orientation if goes crazy 100-300 s/d, 9ms beat error, this said, I checked all installed components as free and located correctly and not over lubricated, all seemed OK, but decided to strip it down again to double check (all was good), without the pallet and balance in the watch felt very smooth on turning the crown so the only question is the balance and hairspring at fault? Is it possible for the balance/hairspring to cause these issues? One thing I did notice is that the hair spring seemed a little slower that all my other I initially put this down to it coming up on the timegrapher as a 1800 bph (all my other watches are 21000 or above), also the watch has a tendency to stop but starts again with a little tilt side to side.

Any thoughts guys? Thanks GDub.

Link to comment
Share on other sites
Nucejoe Distinguished Member

Nucejoe

Posted
Posted

    18000 bph is correct.

 

20 hours ago, GDub said:

Is it possible for the balance/hairspring to cause these issues? 

 Sticky  hairspring due to contamination or magnetisation, sometimes intermittently which is hard to spot with naked eye, making  a vid of oscilator running helps to spot hairspring issues.

 

 

 

  • Like 1
Link to comment
Share on other sites
  • 10 months later...
Nucejoe Distinguished Member

Nucejoe

Posted
Posted (edited)
On 1/17/2023 at 10:47 PM, GDub said:

 as soon as you change the crown orientation if goes crazy 100-300 s/d, 9ms beat error, 

Do you mean ,  when you turn the crown to advance the hands  ? 

Is it pin pallet ? did you oil the escape teeth.

 

Edited by Nucejoe
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • HectorLooi
      Blew it with a coil

      By HectorLooi · Posted

      You don't have to use his special tester. Any good multimeter would work.
    • nevenbekriev
      Pocket watch escape wh

      By nevenbekriev · Posted

      Yes, it looks like GT Revue 30. Doctor, You can not replace escape wheel by the dimensions You listed. One needs to know much more things like number of leaves of the pinion and it's diameter, the position in high of the table and the pinion, the hight between the pivots, the exact pivots diameter... And then, even if suitable wheel is found, one will need to know how to adjust the pallets position correctly. Restoring antique movements is something different than replacing parts. In older movements parts are not interchangeable, this means spare parts do not exist. Here the case is different, but still escapement adjustment will be needed if a wheel from a donor is found. So may be it will be easier to restore the donor for You...Restoring antique movements usually means making of the parts needed and this requires knowlage and working on lathes skill. In this case repivoting of the wheel is the natural solution, but there is a long way that one must walk untill getting ready for such work.
    • Waggy
      How to store one dip

      By Waggy · Posted

      I was looking at Essence of Renata, a chemical used a lot for cleaning hairsprings: "Specially prepared solution for degreasing watch and instrument components. Indispensable for degreasing hairsprings." Looking at the MSDS you can see this is just pure n-Heptane, so could be an option for those who don't want to use the chlorocarbons or hexane?     HF6013 - Horological Essence COSHH Safety Data Sheet Horological Essence_0.pdf
    • Kkramme
      Self introduction

      By Kkramme · Posted

      Great!! 👍 
    • Waggy
      Self introduction

      By Waggy · Posted

      Welcome from a fellow Seiko enthusiast, there are lots of us on this forum.
×
×
  • Create New...