Jump to content

Replace Rotor Bearing

Mark
 Share

Recommended Posts

Mark Distinguished Member

Mark

Posted
Posted

How to replace a rotor bearing in two watch movements - the ETA 2892-A2 movement (on an Omega Dynamic watch). And a Valjoux 7750 movement (on an Ikepod watch).The rotor bearing on these watch movements and their variants often wear faster then the other parts in the watch due to constant movement and vibration.

When servicing these movements it is best practice to replace the bearings so that the automatic mechanism runs optimally.

Replacing them is a near impossible task without the correct tool. The bearing nut tool is made by Horotec and also Bergeon makes one.

There are two key sizes. The 7750 is smaller than the key for the 2892-A2.

Attempting to remove the bolt without the correct tool will likely cause damage to the weight. Refitting the bolt without the correct tool is almost impossible.

The tool is relatively easy to use. I recommend placing the weight on a small staking block so that you can apply pressure to the bolt without depressing the weight (causing damage).

I have created a quick video showing the removal and replacement of the bolt on both these watch calibres.

Feel free to comment below.

Click here to view the article

  • Like 1
Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • rjenkinsgb
      My first Gruens. Precision 510 and N510R movements.

      By rjenkinsgb · Posted

      Snap! I recently finished my Gruen 510 movement - though the case for mine is in a rather sad state; I'm going to try re-plating it (in nickel, it's not a gold one).   Re. the screws, I got a few of the one gram mixed batches from ebay. I've only needed a couple of screws for things so far, both rare, minuscule types - but both in the mix, after enough time sorting through them! The ones such as normal bridge screws are quite common in those lots.  
    • rjenkinsgb
      Any tips to correct a sloppy error?

      By rjenkinsgb · Posted

      Two pins or screwdrivers angled out slightly, pressing through from the barrel centre from the opposite side so they contact just clear of the hole in the lid? eg. Strap pin driver needles or similar.
    • Geotex
      Any tips to correct a sloppy error?

      By Geotex · Posted

      That's a good idea - shrinking down the nut and wrench size from the old casebook trick!
    • GuyMontag
      Movement holder made with 3D printer

      By GuyMontag · Posted

      I missed this earlier. The dial isn't going into the holder, it should sit proud of it. This is what I am currently using which I print for each different movement.    
    • Neverenoughwatches
      Setting lever spring

      By Neverenoughwatches · Posted

      I didn't think pulling to set position would work harden the spring, in that position it is stressed where the arm starts. By work hardening i meant rapid polishing at that point, a bit like polishing a pivot work hardens as it compresses the steel. I doubt polishing by hand would achieve much in that respect though. Its finished, arm polished up mostly at the join to the bridge's main body. I'm ok with it, the screw holes aren't great as i had to open them up by redrilling and positioning it was difficult, I'm not much use with a loupe, opening up with a file might be a better option for me or i could just use the correct drill size 😅. And the detent is way too deep, i had to guess that with the stem release out of position and sat on top, but i only took one measure and went for it, no slowly slowly catch your monkey 😅. First go I'm happy , well sort of, it works and thats a big thing for me, next one will have a bit more finesse.  Anyone thats interested, after filing, i used a 2000 grade home made diamond  micro file and then 20 micron film, the film is much better than wet and dry, more stable to use and doesn't shed cheap grade grit everywhere , then auto polish on a sponge pad.
×
×
  • Create New...