Jump to content

Balance is starting and stopping


Recommended Posts

Hey guys! I just got this Customtime Anno-matic "2000 year" by Agon Chromatic Watch Corp. Upon my first inspection, I have noticed the balance will only run reliably when the watch is face down. I can get the balance running, but if I turn the watch sideways or upside down it halts almost immediately. Do you guys have any ideas as to why this is happening? Perhaps the balance is catching on something in a certain position? Any help would be useful, thank you so much! I can also add more pictures of the movement, if you request it.

20221116_190226.jpg

20221116_190730.jpg

Link to comment
Share on other sites

6 hours ago, Klassiker said:

Most likely your balance staff has a broken upper pivot. If you delicately lift the rim of the balance wheel, does it tip to one side, or is it constrained on its axis? How much play is there?

It doesn't feel or look broken, it's stable in its pivots and it doesn't tilt at all when I try to move the rim. 

Link to comment
Share on other sites

If it hasn't been cleaned and oiled it's a fun guessing game but you will never know. The horizontal positions are the "easiest" for the watch to run in. Now, if the balance is swinging at 270 degrees dial down and then stops in other positions there probably is a fault other than dirt and lack of lubrication. Judging by the thumbprint on the ratchet wheel I'm going with dirty and lack of lubrication 🙃.

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • I think if you want to play Billy big b.ollocks then you have to have something up your sleeve, anyone that knows how to fight, plays dirty. Lets face it a lot of folk that voted for Brexit just rolled uk their sleeves to say up yours EU hoping for good changes. We have idiots for leaders and probably none of them clever enough to clean the shitty stick they were given. I didnt vote, what will be will be.
    • I voted leave too, my reasoning was the the EU is undemocratic, no elected officials. I don't regret it but I  am sad that both sides acted like petulant toddlers.  Shameful.  I'm not on other forums but if I was and left this site, would you shun me? Of course not, we aren't petulant toddlers.  
    • This is a type of tool that may be suitable to remove the bezel - though note that I'm pretty sure the watch should be face down - not face up, as in some of the photos of these tools on amazon & ebay! If you try one one of those, put the movement screws back in first to avoid accidents. https://www.amazon.co.uk/Removal-Professional-Remover-Watchmaker-Diameter/dp/B09XCH4QVN?source=ps-sl-shoppingads-lpcontext&ref_=fplfs&smid=A296NCMMFVXSDN&th=1  
    • Hi, I’m constantly asking my wife to help me with removing the stem in order to complete casing. To expand, this is not a challenge for me when the setting lever is secured by a screw (older calibers). However when the setting lever is attached to a spring loaded setting lever axel, like on more modern calibers, I simply don’t see how to apply enough pressure on the button to get the stem out short of putting the movement face down with the dial and hands attached, which I’m loath to do in order to avoid damaging the dial/hands? what technique should I be using? thanks  
    • Many thanks for your advice (being borne in mind at present) & offer Dell. When I was given the clock the plastic anchor was loose on the arbour (it had split at the 'hole') &, after repairing this, I have been trying to determine whether the spindle (pin) should be perpendicular when the pallet is sitting on a flat surface; or whether, when installed, its L-R extremes (or alternatively its tick & tock points) should lie at equal angles from the vertical when moved with spring absent. I can get the clock to run but in every such configuration the top block has to be turned anti-clockwise (from above) by quite a bit in order to be 'in beat' & it always runs fast (despite the pendulum being set to as slow as possible). This makes me wonder if there is any particular feature of/fault in a torsion spring clock which determines which turn direction (if any) is necessary to get it 'in beat'; & whether there would be a different set of settings that would get it running nearer to time at somewhere around the mid timing/inertia position which would then allow tweaking of the fast/slow setting.
×
×
  • Create New...