Jump to content

Seiko Spring Drive

Geo
 Share

Recommended Posts

  • 3 years later...
Evan New Member

Evan

Posted
Posted

I was hoping to see some repair videos, or movement reviews on this variety of watch movement, however, I can't seem to find any here. Youtube does have one build video of these watches by a factory rep in a jewelry store. 

Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted

There are many technical reviews on the net for Seiko Spring Drive. I recall a very good one with detailed pictures which was done at an American horological academy few years ago, you should be able to find it with Google. 

The reason why there are no repair or service articles is that by one side the owners are unwilling to give the watch to anyone but Seiko, and on the other hand even competent watchmaker are unwilling to touch these, as they are unfamiliar with them and would not get parts from Seiko.

In fact even Seiko service centers anywhere In the world will send to Japan the Grand Seiko, Credor or Spring Drive models given to them for service or repair. 

  • Thanks 1
Link to comment
Share on other sites
Nucejoe Distinguished Member

Nucejoe

Posted
Posted
2 hours ago, jdm said:

There are many technical reviews on the net for Seiko Spring Drive. I recall a very good one with detailed pictures which was done at an American horological academy few years ago, you should be able to find it with Google. 

The reason why there are no repair or service articles is that by one side the owners are unwilling to give the watch to anyone but Seiko, and on the other hand even competent watchmaker are unwilling to touch these, as they are unfamiliar with them and would not get parts from Seiko.

In fact even Seiko service centers anywhere In the world will send to Japan the Grand Seiko, Credor or Spring Drive models given to them for service or repair. 

Right, even parts to the bracelette, Damaged bracelette on mine, I am not going to pay an arm and a leg. 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • rjenkinsgb
      Any tips to correct a sloppy error?

      By rjenkinsgb · Posted

      Two pins or screwdrivers angled out slightly, pressing through from the barrel centre from the opposite side so they contact just clear of the hole in the lid? eg. Strap pin driver needles or similar.
    • Geotex
      Any tips to correct a sloppy error?

      By Geotex · Posted

      That's a good idea - shrinking down the nut and wrench size from the old casebook trick!
    • GuyMontag
      Movement holder made with 3D printer

      By GuyMontag · Posted

      I missed this earlier. The dial isn't going into the holder, it should sit proud of it. This is what I am currently using which I print for each different movement.    
    • Neverenoughwatches
      Setting lever spring

      By Neverenoughwatches · Posted

      I didn't think pulling to set position would work harden the spring, in that position it is stressed where the arm starts. By work hardening i meant rapid polishing at that point, a bit like polishing a pivot work hardens as it compresses the steel. I doubt polishing by hand would achieve much in that respect though. Its finished, arm polished up mostly at the join to the bridge's main body. I'm ok with it, the screw holes aren't great as i had to open them up by redrilling and positioning it was difficult, I'm not much use with a loupe, opening up with a file might be a better option for me or i could just use the correct drill size 😅. And the detent is way too deep, i had to guess that with the stem release out of position and sat on top, but i only took one measure and went for it, no slowly slowly catch your monkey 😅. First go I'm happy , well sort of, it works and thats a big thing for me, next one will have a bit more finesse.  Anyone thats interested, after filing, i used a 2000 grade home made diamond  micro file and then 20 micron film, the film is much better than wet and dry, more stable to use and doesn't shed cheap grade grit everywhere , then auto polish on a sponge pad.
    • RichardHarris123
      Setting lever spring

      By RichardHarris123 · Posted

      I'm assuming that every time you set the watch you are work hardening the detent spring, maximum hardening is  where it meets the plate due to maximum deflection.   That's why it snaps there.  The Young's modulus may be the same but after it's reached its maximum yeid strength it breaks.  My mechanic engineering is very rusty, correct me if I'm wrong. 
×
×
  • Create New...