Jump to content

Vintage Homemade Crystal Press.............refurbished.


Geo

Recommended Posts

I purchased a cheap Chinese crystal press when I took up watch repairing/refurbishing a few years ago, this was one of the lever operated type with nylon dies. This has served me very well, but there are some jobs that a screw type of press is far better for because of the more sensitive control.

Being a canny Scot, I kept an eye on eBay for a second hand Robur or Horotec and stumbled across this antique home made press for £14 delivered.

post-124-0-00007400-1435348982_thumb.jpg

The engineer in me immediately saw the potential, all it needed was stripped down, modified to take new dies and repainted.

The other thing that was required was a set of new aluminium dies, so after a search on AliExpress I purchased these for £26 delivered from China.

post-124-0-76073200-1435349243_thumb.jpg

Right, down to business.

(1) Modify the lower die holder to accept the 6mm threaded alloy dies.

post-124-0-94920900-1435349432_thumb.jpg

(2) Make an adaptor to fit the bottom of the ram with a 6mm thread to take the dies.

(3) Machine the lower end of the pillar to give clearance for the largest die.

post-124-0-36916600-1435349599_thumb.jpg

(4) Accurise the dies to ensure that the faces are parallel. Many were slightly out of truth.

post-124-0-32890100-1435349819_thumb.jpg

post-124-0-79416000-1435349919_thumb.jpg

(5) Remove paint and rust from press, paint and polish.

post-124-0-97095300-1435350044_thumb.jpg

(6) Reassemble.

post-124-0-37129700-1435350123_thumb.jpg

Total cost of complete set £40.................well pleased!

post-124-0-85889900-1435350317_thumb.jpg

post-124-0-51590900-1435350248_thumb.jpg

  • Like 10
Link to comment
Share on other sites

PS didn't know you had a lathe. Wish I had room for one

Wouldn't be without it CB, I also have a lightweight milling machine. I put together a machine shop when I was building target pistols many years ago, now it so handy for both my motorcycle and horology interests.

post-124-0-45203200-1435391763_thumb.jpg

post-124-0-66002600-1435433663_thumb.jpg

  • Like 4
Link to comment
Share on other sites

  • 2 weeks later...

Looks great Geo, nice work. It reminds me that I bought a press very similar to yours meaning to convert it to take various dies I already have. You've inspired me to have another look at it, although I'll have to try and figure out a way to do it without the use of any similar equipment :). Not that easy when you're not particularly mechanically minded! Thanks for sharing.

Stephen

  • Like 1
Link to comment
Share on other sites

  • 4 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Many thanks for your advice (being borne in mind at present) & offer Dell. When I was given the clock the plastic anchor was loose on the arbour (it had split at the 'hole') &, after repairing this, I have been trying to determine whether the spindle (pin) should be perpendicular when the pallet is sitting on a flat surface; or whether, when installed, its L-R extremes (or alternatively its tick & tock points) should lie at equal angles from the vertical when moved with spring absent. I can get the clock to run but in every such configuration the top block has to be turned anti-clockwise (from above) by quite a bit in order to be 'in beat' & it always runs fast (despite the pendulum being set to as slow as possible). This makes me wonder if there is any particular feature of/fault in a torsion spring clock which determines which turn direction (if any) is necessary to get it 'in beat'; & whether there would be a different set of settings that would get it running nearer to time at somewhere around the mid timing/inertia position which would then allow tweaking of the fast/slow setting.
    • Now this has happened I bet China or India just to name two will start to produce none genuine parts.  I did. But idiot Boris Johnson failed miserably in his negotiations. The E U stitched up the UK like a kipper. Nigel Farage  offered his help but big head Boris declined. So this is why we are in this mess all because Johnson wasn't clever enough.  
    • Hands up all those who voted to leave the EU 😂, oopsie.  UK has just signed the Hague convention, next year that will provide cross border clout to British courts.
    • Ive heard about that oil before for the lever pins. I found it easy to work on , it didn't have a whole lot of pivot wear but i bit sloppy on the lever cock, i think you have to live with what you have or bin it. Stiff to wind and set ?  Not a cannon pinion issue that has no friction thats made up further back and if I remember the barrel drives the hour wheel. No problem on this one .Let me know when you start it as i have another that donated to this one, i can work alongside you with it, two heads are better than one. 
×
×
  • Create New...