Jump to content

Main Spring Replacement, What Do I Need?

No8yogi

By No8yogi
in Watch Repairs Help & Advice

 Share

Recommended Posts

Mark Distinguished Member

Mark

Posted
Posted

That's annoying. :(

 

The only thing you can do is gently squeeze it, most likely without the arbor in place. But it is very risky - the spring is very brittle but can bend a small amount. Baby steps - be very very careful and don't apply pressure where the hole (for the hook) is because that is the weakest part.

Link to comment
Share on other sites
Geo Distinguished Member

Geo

Posted
Posted

I had the same problem a few months back. I very gently eased it into a tighter curve using round nosed pliers. As Mark says, make sure that you do not bend it where the hole for the hook is. Ideally it should be slightly tighter than the circumference of the arbour to make sure that it grips it when fitted. It worked for me, but be very careful.

  • Like 1
Link to comment
Share on other sites
No8yogi WRT Addict

No8yogi

Posted
  • Author
Posted

Going to bed!!

Got the mainspring sorted train running nicely

It just won't tick! Hairspring looks good balance turns smoothly

The it happened the winder frikin broke off!!!!?!!!!

Snapped clean in half I can't be bothered to go find it suffice to say I am gutted

Link to comment
Share on other sites
Geo Distinguished Member

Geo

Posted
Posted

That's a real bummer about the stem, I hope you can track down another.

Regarding the watch not ticking, if the spring is still wound try this first.

Remove the the balance and ensure that the escapement lever flicks sharply from side to side when touched very delicately with a dry oiler. If it does then you probably put the balance wheel in the wrong position regarding the escapement lever. Looking down on the escapement lever, if the lever is resting to the right, make sure that the roller jewel on the balance is rotated further to the right than the end of the lever so that it will catch the end of the lever when it rotates to the left. If you do this the balance should start up as you locate the cock on the main plate. The reverse of this is true if the balance lever is initially resting to the left.

If the escapement lever does not flick sharply from side to side with the balance wheel removed, the problem could be that you oiled the escapement jewels. They should be free from oil. Failing this you will have to completely strip the watch and check every component in detail followed by staged assembly testing each set of mating components as you go.

Bast of luck............and don't give up!

Link to comment
Share on other sites
Mark Distinguished Member

Mark

Posted
Posted

As Geo said - don't give up. It can be discouraging when this happens.

My advise is to always take a step back when things are not going right. If you start feeling frustrated when a repair is going wrong then stop! Come back to it after you have cleared your head. Go for a drive or watch some telly

When you come back to the job you should be calm and ready to tackle it again.

In short, it is very difficult to fault find when you are in a frustrated state.

Having said all that, we all make mistakes from time to time. So just take a breath and then go back to it with fresh eyes.

Good luck mate :)

Sent from my iPhone using Tapatalk

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • ManSkirtBrew
      1972 Bulova President "E" Sea King 11ACACB movement

      By ManSkirtBrew · Posted

      Unfortunately I'm not that lucky. I started on the train side and after I noticed the binding I pulled everything out except the driving wheel to rule everything else out. It still binds. I'm going to double check that the pinion is fully seated on the staff first, then if no joy I'll push the bridge jewel up a fraction of a mm. Fingers crossed!
    • Waggy
      Rado rotor removal

      By Waggy · Posted

      Happy to have helped, great way to start the day with a win! 🥳
    • doober
      Rado rotor removal

      By doober · Posted

      Thank you for the advise!! It worked. The setting screw was a lock/unlock to remove the rotor. 
    • GuyMontag
      1972 Bulova President "E" Sea King 11ACACB movement

      By GuyMontag · Posted

      I have that French tech sheet too, it is a little different than the English one (eg, it doesn't have the auto works diagram). BTW, it looks like you are looking up the case number in the 1979 ABC supplement. The 1974 ABC catalog does have the 3093 case. As you determined it takes the 1222-5 crystal.  When I serviced my President 'A' (which also takes that crystal), I was able to fit a 29.8 crystal from my DPA crystal assortment. Those are, in my opinion, a great deal. The assortment comes with 10 sizes each from 27.8mm to 32.4mm in 0.2 increments. I pretty much use them for any non-armored crystal that takes a high dome crystal. I think they no longer make them but Cousins has still has some in stock but when I bought them they were around $40 for the set and now they are around $100. Still, at 40 cents a crystal it's still a good deal. For the large driving wheel, I remember I once assembled the keyless/motion works first and when I placed the large driving wheel it was interfering with the setting wheel on the dial side as the teeth were not fully meshing and it wouldn't fully seat. If that isn't the issue I got nothing and am looking forward to see how you solve it 🙂
    • Waggy
      Rado rotor removal

      By Waggy · Posted

      Not sure, but just looking at it, it seems like the screw on the right may be a fake? The one on the left may not be a screw in the regular sense at all, rather a 2 position device, I think you need to point the slot towards either of the 2 dots and one will secure and one will open. Like I said this is just my best guess looking at the pictures.
×
×
  • Create New...