Jump to content

Hello


Recommended Posts

Novice here. And thanks in advance for any advice.

Recently entered the world of watch making, and since I know little of nothing, I have a question.

I decided to start with pocket watches, and I have an old Waltham pocket watch I am working on.

It is running super slow (around -250s/d with the regulator in the middle)

The two balance wheel timing screws are turned all the way out. And the main spring is apparently gunked up. It winds stiff, and unwinds like it is caked with old grease.

So, I am going to tear it all the way down for a thorough cleaning.

But the question is - what happens when I adjust the regulator. 

I had the regulator maxed out to the + side so running about -40s/d.

But when I barely move the regulator, IE just nudge it, The s/d may go to +200 for a short while then settle back down.

I have other pocket watches that don't jump to this extreme.

So, I am wondering if this is a problem with the regulator pins or something else?

 

 

Link to comment
Share on other sites

10 minutes ago, tammons said:

So, I am wondering if this is a problem with the regulator pins or something else

Whatever strange behavior happens in its present state means little or nothing. 

Only after it has been cleaned to perfection, all parts inspected and found to be good at least, then put back and lubricated correctly, you will be able to make meaningful observations about its performance. And It will be better that you use a timegrapher to make calls at that point. 

BTW if you really care about this watch it would bw better that you practice first on something else of no value whastoever, especially about hairspring and balance handling. 

  • Like 2
Link to comment
Share on other sites

Welcome to WRT forum. 

Timegrapher results be nice.

 Release barrel power through the click so oscilator wont run, then hairspring should not come to contact with neither the boot nor pin, as you move the regulator arm throughout the entire terminal curve.

The transiant state you see can be due to such a contact momentarily throwing the oscilator out of beat.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • nevenbekriev- You nailed it with your description of me and my reaction when the clock started ticking again. I am a newbie.  I love the sound and idea of mechanical clocks but the idea of owning one and trying to keep them running has never appealed to me. My wife bought this one and an antique German wall clock.  When I looked into having someone repair them for me, the universal response was "it's really expensive to work on them, you should just replace the movement". So, I had nothing to lose, I started researching them and opened them up. The wife is happy because she hears the sound of the clocks again. But I have gone down the "accuracy" rabbit hole. In the vertical position, the balance wheel was not floating. It was sitting on the bottom of the frame. I adjusted the lower spring collet and got it floating. It easily passed the 270 degree 3 to 5 minute oscillation test. It took 8 minutes for the wheel to completely stop moving.  I put it the unit back in the movement and checked the safety pin. It does not touch the safety roller anywhere in +/-270 degrees rotation from neutral position. But the amplitude of the rotation with the spring fully wound is weak based on what you are saying. It rotates +/-90 degrees from the neutral position.  No, I did not take the movement completely apart.  That seemed way outside my skill set at the time. There is a reason I became an electrical engineer and not a mechanical engineer. I am much more comfortable with moving electrons than tiny moving metal parts. Will I do it in the long run? Anything can happen. I don't seem to be able to let it go.
    • Isn't that the same guy who told Zelenskyy to escalate the war with Russia/Putin when they already had a peace deal? 2 years later and we have half a million young Ukranian boys dead. He doesn't seem very clever...
    • Thanks guys.  quick question. For automatic movement, particularly this one. can I power down the main spring by pushing this rachet down?  i've gotten pretty used to SW210 and powering down a manual movement. But so far i've only been waiting for the auto movement to run out of juice before opening the case.     
    • @Murks the problem you have mate is most watch cases out there to buy are for Seiko NH3X, ETA 2824 and maybe Myota 8XXX movements, oh also the big ETA 6978/9 movements which the dials start around 28.5mm. You might find one on a Google search but I suspect your main chance will be buying cheap quartz ladies watches and hopefully find one of the right size and condition that is acceptable. 😞   Tom
    • The anchor pin should be perpendicular when the anchor is sat on a flat surface and if you post a close up picture of the backplate I will be able to tell you the correct torsion spring , running fast or slow is usually wrong Torsion spring. Here is a video from my YouTube channel showing how I set the beat  
×
×
  • Create New...