Jump to content

Vostpk Factory Tour

HectorLooi
 Share

Recommended Posts

nickelsilver Distinguished Member

nickelsilver

Posted
Posted
50 minutes ago, grsnovi said:

I can say that those hand-operated presses wouldn't be allowed in the USA with all of the OSHA safety regulations. Too exposed.

Yes, on a machinist forum I frequent someone wanted to sell some small presses and there was a unanimous cry "if they were made after 19xx they're scrap". Presses scare the bejezus out of me.

  • Like 2
Link to comment
Share on other sites
MechanicMike Super WRT Addict

MechanicMike

Posted
Posted

they can and are allowed-you'd be surprised at how many are out there that do still exist and run. I know cuz I've worked on lots of them for years. most if not all have been retrofitted and upgraded with dead man switches and light curtains for safety, from the small 1 tons all the way up to the heavy hitters like the 400 ton that have foundations and pilings that go as deep as 40 ft. if you get anywhere near the business end of the press and it shuts it down in less than what it takes to blink an eye. they're fascinating to watch, much less fun to work on tho...this is interesting to see that they still use ancient presses in their facility. for further reading look up the history of Deuber-Hampden American pocketwatches and where the whole plant and several of its technicians went to in 1921...

  • Like 1
Link to comment
Share on other sites
nickelsilver Distinguished Member

nickelsilver

Posted
Posted

I remember reading on the machinist forum about a guy carrying out a punch and die set, setting it in someone's trunk, and the set slamming closed as he set it in. There was a mention of "popping grapes" which horrified me but apparently the bloke made a full recovery. I'm eternally terrified of punch sets.

  • Like 1
Link to comment
Share on other sites
HectorLooi Distinguished Member

HectorLooi

Posted
  • Author
Posted

What amazes me is there was absolutely no attempt to "sanitize" or hide anything. The setup looks like it was from the '80s. Except for the part where they were using what looks like China made timegraphers.

I can't wait to see the insides of a Chinese watch factory.

  • Like 1
Link to comment
Share on other sites
RichardHarris123 Distinguished Member

RichardHarris123

Posted
Posted
4 hours ago, HectorLooi said:

What amazes me is there was absolutely no attempt to "sanitize" or hide anything. The setup looks like it was from the '80s. Except for the part where they were using what looks like China made timegraphers.

I can't wait to see the insides of a Chinese watch factory.

Most of the set up looked way older than the eighties to me.  Does anyone have any idea how old some of the machines are?

Link to comment
Share on other sites
Neverenoughwatches Distinguished Member

Neverenoughwatches

Posted
Posted
6 hours ago, nickelsilver said:

I remember reading on the machinist forum about a guy carrying out a punch and die set, setting it in someone's trunk, and the set slamming closed as he set it in. There was a mention of "popping grapes" which horrified me but apparently the bloke made a full recovery. I'm eternally terrified of punch sets.

🤢 🤮

Link to comment
Share on other sites
dadistic Distinguished Member

dadistic

Posted
Posted

Way back when the super for my building was a punch press operator during the day. He was missing several fingers.

No doubt operators under time pressure would disable the safety manacles on the press, they were uncomfortable and interfered with loading the press.

Modern optical fences are much better.

  • Thanks 1
Link to comment
Share on other sites
  • 2 weeks later...
spectre6000 Distinguished Member

spectre6000

Posted
Posted

I watched the Vostok video. YouTube figured I liked it, and served me up this one of the Raketa factory this morning:

If you're not hip to the tech, you can turn on closed captions, and under settings have it auto-translate to whatever language. It's a bit hit or miss, and started out good, but toward the end of the video (I assume when things started getting technical) it pretty much fell apart into an unintelligible word salad.

The first half looks to be just hanging out in the gift shop, but they do ultimately show the actual manufacturing. Very different from Vostok. Vostok is much bigger, but looks like ancient tools being kept alive by accident. Raketa looks much more like what I would expect a Russian watch manufacturer to look like; old tools, but reasonably well maintained. If I were to buy a new Russian watch today, I'd definitely be looking at a Raketa over a Vostok.

  • Like 1
Link to comment
Share on other sites
MechanicMike Super WRT Addict

MechanicMike

Posted
Posted
On 6/27/2022 at 7:43 PM, nickelsilver said:

set slamming closed as he set it in. There was a mention of "popping grapes"

worked with a guy in a huge mfg. facility that included a punch press dept. . one of the operators was missing his left hand and forearm to just below his elbow. still working on the presses 30+ years. 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • JohnR725
      Blew it with a coil

      By JohnR725 · Posted

      the problem with vintage watches and yes quartz watches can be vintage is availability of parts will be a problem. I have a link below where we can cross reference the coil and  I was hoping for more. Another problem for vintage parts are everyone on the group gets used to ordering from online. Conceivably the physical material houses that still exist out there might have the part and you'd have to reach out to them and see if anyone has one. this is because they don't list every single part that they have online with the exception of cousins where everything they do is online work just doesn't exist but the other material houses can have stuff not listed. Otherwise just set up a search on eBay and sooner or later it will possibly show up if you're lucky.   http://cgi.julesborel.com/cgi-bin/matcgi2?ref=SEK_6020A  
    • watchweasol
      Self introduction

      By watchweasol · Posted

      Hi welcome to the forum.    Enjoy
    • JohnR725
      Pocket watch escape wh

      By JohnR725 · Posted

      the bestfit book refers to Revue as wittnauer and the fingerprint we have this.
    • Waggy
      Difference between AS 1686 and ST 1686

      By Waggy · Posted

      Maybe a little off-topic, but it still amazes me that most people (and myself before I got into this hobby) don't realise that the movement of their watch was (in most cases) not made by the name on the dial of the watch. This is especially true of many 'fashion' watches which use the cheapest of cheap movements ($4 each) which are completely out of proportion to the overall cost of the watch ($++100s). Usually the actual manufacturer is stamped somewhere inconspicuous on the movement, usually around the balance, and this is what you need to find so you can locate spare parts or servicing manuals etc. This is like buying a top of the line Rolls Royce Phantom and learning it has a BMW engine..... oh wait a minute, it does! (6.75-liter, 460-horsepower BMW V12 engine - reference)
    • JohnR725
      1944 bulova a-11 trouble removing movement

      By JohnR725 · Posted

      I have an image of what the case is supposed to look like disassembled. then an interesting website https://www.mybulova.com/vintage-bulova-catalogs there's all sorts of interesting things here for anyone in watch repair. but for the particular subject these are the two I recommend. You can see page 7 is where I got the image of the case. Then the word apartment technical manual is really a training manual of watch repair covers wristwatches and pocket watches everybody should have a copy of this.  
×
×
  • Create New...