Jump to content

Gear post knarled after broken screw removed


Recommended Posts

Hi All,

I am either trying to repair this pivot or obtain a new main plate.  I have not been able to find a main plate.  The movement is a Monpilier 60.  My question is, what is the name of the cutter that makes these holes?  I drill/reamer for the center hole?  Can I silver solder the hole and recut things the way I need it to be?

Thanks,

Don

IMG_2070.jpg

Link to comment
Share on other sites

Hi Don  I think the best approach is to re bush the hole and then droach it for the center vwheel shaft.  Carefully drill or brach the worn hole and press in a bush, either a blank bush or better still one with a hole slightly smaller than the diameter of the shaft to allow a tailored fit.

Link to comment
Share on other sites

This is a very tricky repair; typically the issue is wear on the outer diameter, are you dealing with that or stripped threads from the screw? Since this is over the hole for the stem pivot, there is very little material around it.

 

Once approach would be to bore it out, and press in a new threaded piece the correct outer diameter. It would require re-drilling the hole for the stem pivot, and careful fitting so that it doesn't budge when screwing in the screw. A solution is making a stepped tube, and an appropriate recess for the step on the movement side of the plate (just a little step, 0.1mm is enough). It's fiddly work.

 

My preferred method if there is wear on the outside, and if there is enough material between the inner and outer diameters of the post, is: in a faceplate, turn the outer diameter of the post down, leaving enough material that it can take a sleeve. Make sleeve from steel, harden, temper, install with Loctite 648. Often this is a solid post, no hole or thread, so it's less of a challenge.

Edited by nickelsilver
  • Like 2
Link to comment
Share on other sites

The real experts have responded with ideas, but I have yet another idea that might work.

Leave the current post in place and make a bushing to insert inside of it.  Tap that bushing with a smaller hole and make the appropriate screw.  Then make a tool with a hole of the correct outside diameter and use it to burnish the outside so that it is a smooth round post.  You will still need to drill a hole for the stem but you will have a guide.

This is a serious repair requiring a lathe and some skill.  Even though I am an amateur, I would try it since the plate, as is, is useless.

I would be interested to know of @nickelsilveror @watchweasolthinks this could work.

Link to comment
Share on other sites

I know this doesn't help the OP, but I had to sleeve one of these externally yesterday so I snapped some pics. You can see the post is super worn, and it made setting very hard. I turned the post down in a faceplate, turned up the sleeve in beryllium copper, pressed it on, and bingo!

 

 

20220621_133414.jpg

20220621_155639.jpg

20220623_152340.jpg

20220623_152318.jpg

  • Like 4
  • Thanks 1
Link to comment
Share on other sites

1 hour ago, watchweasol said:

A very neat job from the professional with thr right tools and skill.  may one ask how long it took to complete.  a brilliant job.

Thanks WW. Probably about 20 minutes start to finish- but I have a dedicated lathe for faceplate work with optical centering, and the (tiny) cutting tool I used there was ready to go. My small lathe is always ready to go, haha,  as I use it every day, usually multiple times, so the sleeve took no time. Probably spent as much time measuring as cutting/ installing.

 

This is for a maker that starts with a big R, and apparently this is such an issue that they supply some of their repair centers with a special setup for recutting the post and sleeves ready to fit. You'd think they'd just fit a hard steel sleeve there or something to begin with...

Edited by nickelsilver
Link to comment
Share on other sites

15 minutes ago, nickelsilver said:

Thanks WW. Probably about 20 minutes start to finish- but I have a dedicated lathe for faceplate work with optical centering, and the (tiny) cutting tool I used there was ready to go. My small lathe is always ready to go, haha,  as I use it every day, usually multiple times, so the sleeve took no time. Probably spent as much time measuring as cutting/ installing.

 

This is for a maker that starts with a big R, and apparently this is such an issue that they supply some of their repair centers with a special setup for recutting the post and sleeves ready to fit. You'd think they'd just fit a hard steel sleeve there or something to begin with...

Wouldn’t it be easier to drill out the post on a lathe, then reinsert a new steel post into the hole? I assume that is how some of the posts on main plates are made anyway.

Link to comment
Share on other sites

2 minutes ago, ifibrin said:

Wouldn’t it be easier to drill out the post on a lathe, then reinsert a new steel post into the hole? I assume that is how some of the posts on main plates are made anyway.

On this one the material is too thin to reliably hold a new pressed in post.

  • Like 1
Link to comment
Share on other sites

Just now, nickelsilver said:

On this one the material is too thin to reliably hold a new pressed in post.

Oh you mean that the original post was originally machined out of the same brass block as the main plate? Meaning that the post was not inserted in, but is actually part of the entire main plate?

Link to comment
Share on other sites

the title implies the damage was done when the screw was being removed?

just a reminder for people that are new here. If you break a steel screw off in a brass plate. Providing there is no other steel components in other words you have to remove everything. The steel screw can be dissolved out. Versus attempting to remove it other methods which can be destructive. I find often times people forget or don't realize there are other ways of getting screws out and dissolving works really really nicely.

 

 

3 minutes ago, ifibrin said:

Oh you mean that the original post was originally machined out of the same brass block as the main plate? Meaning that the post was not inserted in, but is actually part of the entire main plate?

yes all machined out of one piece of brass. Good for manufacturing point of view very bad from a repair point of view

  • Like 1
Link to comment
Share on other sites

4 minutes ago, ifibrin said:

Oh you mean that the original post was originally machined out of the same brass block as the main plate? Meaning that the post was not inserted in, but is actually part of the entire main plate?

Yes, which is often (usually) the case.

Link to comment
Share on other sites

4 minutes ago, JohnR725 said:

the title implies the damage was done when the screw was being removed?

just a reminder for people that are new here. If you break a steel screw off in a brass plate. Providing there is no other steel components in other words you have to remove everything. The steel screw can be dissolved out. Versus attempting to remove it other methods which can be destructive. I find often times people forget or don't realize there are other ways of getting screws out and dissolving works really really nicely.

 

 

Do mainplates generally have a number of steel posts, especially in the motion work or the keyless work? Wouldn’t this dissolve those steel posts as well?

Link to comment
Share on other sites

12 minutes ago, ifibrin said:

Do mainplates generally have a number of steel posts, especially in the motion work or the keyless work? Wouldn’t this dissolve those steel posts as well?

generally the plates are made out of brass all brass.  everything that resembles a post is just machined in typically. 

  • Like 2
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • people be honest.... Swatch is evil for the watchmakers and repairers, BUT not everything in watches from Switzerland is from the Swatch-Group. As far as i know, Selitta got sacked by Swatch as a Movement-Assembler for them and they started to produce Movements in their own Name with slight Modifications. As far as i know, they sell Parts to the Market for their Movements. In most cases, if a ETA-Movement fails, it is a valid Option to replace it with a Selitta Movement, which i consider the Solution for this Mess with the Swatch-Group...... I have no Connection to anybody at Selitta, but being a Swiss-Guy, i still like to have Swiss-Made Watches, but not from the Swatch-Group.   ok ? regards, Ernst
    • Just one more greedy act by Swatch. They started a number of years ago here in the US..cutting off supplies to watchmakers that could build complications that many Swatch houses couldn't even touch. Old school masters who had gone through some of the most prestigious houses in the world. Otto Frei has some statements on their page about it. I tell all my customers to avoid new Swiss watches like the plague,..unless they just want an older one in their collection that still has some parts out on the market, or they have really deep pockets and don't mind waiting months and paying through the nose to get it back. Plenty of others to choose from..IE Seiko,..or other non-swiss brands Even a number of Chinese brands are catching up with the Swiss,..and I think that in time, their actions will be their downfall
    • Yes. If that's not what you are experiencing...start looking for something rubbing. A 1st guess is that one of the hands is rubbing against the hole in the center of the dial. Especially if you now have lower amplitude in face up/ face down positions.
    • Once a movement has the dial and hands put back and it is recased, would you expect the assembled watch to have the same amplitude as when the movement is in a movement holder and is without hands and dial? Thanks
    • C07641+ not sure what the "+" is for after the last digit.
×
×
  • Create New...