Jump to content

Greetings from New Mexico

OneGold

By OneGold
in Introduce Yourself Here

 Share

Recommended Posts

OneGold New Member

OneGold

Posted
Posted

Hello all,

My name is Floyd and I've recently fallen down the repair rabbit hole. So far I've service a new seagull movement, and a couple Ingersoll pocket watches. The time had come to try my hand at a refurbish and I bought a non runner off of fleabay, a beautiful little Octo watch. After starting the teardown I realized that sourcing information for parts was going to be the next challenge and here I am! I'll need a crystal, case back gasket and most likely a new crown. I'm looking forward to learning and improving through the help of this community.

 

Cheers

IMG_20220518_191803.jpg

Link to comment
Share on other sites
grsnovi Distinguished Member

grsnovi

Posted
Posted

Hi Floyd, welcome to WRT!

I'm also pretty new so take everything I say with a grain of salt.

You ought to be able to measure the case ID to determine the crystal size and then purchase one of either side of the diameter you think ought to work.

As to other parts, there are a couple of resources that will help. One is a website in Germany that will help with information on the movement. The other is a book (that I don't yet have) that seems to have a lot of information. Many of the vendors have this database available online and there are pdf versions that you can get on CD.

Looking here will give you a list of domestic (USA) resources for parts and tools if you haven't already found some.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • VWatchie
      Epilame / Fixodrop

      By VWatchie · Posted

      Sounds great! And yes, I would use grease for the keyless as well although treating the parts with epilame would make the grease less likely to spread in the long run. Not critical but won’t hurt. My current strategy is to epilame treat all parts getting in contact with oil or grease.
    • Knebo
      Epilame / Fixodrop

      By Knebo · Posted

      Hello everyone, for what it's worth, here is my approach: 1. Escape wheel submerged in Epilame, then dried quickly with a hairdryer. Then the final tip of the pivots are cleaned by poking into pithwood. The logic being that the Epilame is removed at the intended contact point (to avoid any residue that may mix with the oil), but remains in the areas where oil is not supposed to spread to (further down the pivot towards the wheel). The escape wheel teeth also benefit from having Epilame to keep the 9415 in place.  2. I use a syringe to treat only the pallet stones. I suspend the pallet fork with some Rodico so that the stones hang downwards. I notably use a rather thick needle where a drop WON'T form, but rather where the Epilame liquid stays in the needle tip, which I then dip into the pallet stones. It requires some practice to get the right amount of Epilame into the needle tip, but it works for me now. This way, no drop will "jump" onto the pallet fork and potentially go all the way to the pivots.  3. I let the movement run for a few minutes without lubricating the pallet stones... to scrape off the Epilame in the intended contact "channel". Then I remove the balance again and lubricate the exit pallet stone with 3-4 successive drops. See the "channel" that forms on the pallet stone in the picture -- not so easy to see, but it's visible.       I am conflicted about the use of Epliame in balance jewel settings. My impression is that the two jewels sufficiently suspend the oil (even 9010). Apparently Rolex recommends NOT to use Epliame there (heard from a former Rolex service center watchmaker), as it could cause additional wear. Apart from that, I follow specific instructions where I can find them. E.g. the infamous Rolex reverser wheels or sometimes (parts of) the seconds wheel. Exception: I'm currently servicing an Eta 2824 and will probably ignore the service sheet that recommends treating the whole keyless works with Epilame and then using HP1300... I'll skip the Epilame and use 9504 grease.        
    • GuyMontag
      Movement holder made with 3D printer

      By GuyMontag · Posted

      I'm going to give this a try today/tomorrow on my UTC33/Seiko 66, thanks!
    • RichardHarris123
      Intro

      By RichardHarris123 · Posted

      Hello and welcome from Leeds, England. 
    • oldhippy
      Without Our Forum

      By oldhippy · Posted

      Don't forget Mark is a hard working watch maker so he is also tied up with work. I'm sure he is keeping his eye on this forum making sure it is running along nicely. 
×
×
  • Create New...