Jump to content

Replacement Crystal for Seiko SSB181P1 (8T67-00A0)


Zip86

Recommended Posts

Hi there...my son got a new Seiko SSB181P1 for Christmas (see pic)...as he was showing it off to his girlfriend, he took it off and dropped in on the tile floor, shattering the crystal.  I can't seem to find a replacement crystal...nothing seem to come up when I search.  Any help?

 

Capture.JPG

Link to comment
Share on other sites

5 hours ago, Zip86 said:

I can't seem to find a replacement crystal...nothing seem to come up when I search.

Thr Seiko P/N Iis obtained from the reference numberon the back, not the marketing code. However you don't need that because flat crystals are normally replaced by generic ones easily obtained. Measure thickness from a fragment and the recess in the case with vernier calipers. Then a crystal press is needed for refitting, reason for which all in all it may be better to give it to a watch shop.

  • Like 1
Link to comment
Share on other sites

You want Seiko crystal 370PA1LN03, which you can probably still buy from the suppliers listed in the where to get parts sticky topic.

But like @jdm said, it's probably a standard flat crystal you can obtain cheaply from many places.  From the code, we know its diameter is 37.0 mm, which like most Seiko crystals is a standard size.  It's also pressed in, glass, transparent, with no coating.  But, we can't tell how thick it is!  For some reason Seiko thinks asking a crystal its thickness is like asking a woman her weight and prefers to keep a bit of mystery about this value.  Hopefully you have a piece you can measure the thickness of!

If it's a standard thickness like 1.0, 1.5, 2.0 mm then you can get sapphire crystal on alix/ebay from China for not much cost, but a bit of a wait shipping wise.

There is a white plastic ring, which is between the crystal and the bezel.  It's crushed when the crystal is pressed in and should be replaced.  But you don't always have to replace it if it's not damaged.  It's Seiko part 8661-2290, but a generic plastic "I" gasket for a 37.0 mm crystal will probably work too.

You can't push it in with your fingers.  You need a press.  There are models that are quite inexpensive on amazon/alix/ebay/etc.  If you have not pressed in a crystal before, you will quite possibly damage the plastic gasket because the crystal won't want to go in straight.  Get a couple spares.  The generic ones are cheap.

Link to comment
Share on other sites

1 hour ago, xyzzy said:

From the code, we know its diameter is 37.0 mm, which like most Seiko crystals is a standard size.  It's also pressed in, glass, transparent, with no coating.

This info (not a secret), which  I didn't give to not further confuse the owner  - he needs to gets the watch repaired, not become a Seiko technical expert, is derived from obtaining the part number from online databases, and then decoding the P/N using the table attached. 

Crystal Codes.pdf

 

1 hour ago, xyzzy said:

But, we can't tell how thick it is! 

Exactly. That is one reason why one always needs to measure a Seiko crystal to be replaced. The other is that obtaining the original crystal can be simply impossible, or unreasonably expensive. Let's remind that a flat mineral glass crystal cost about 1 Euro.

 

1 hour ago, xyzzy said:

If it's a standard thickness like 1.0, 1.5, 2.0 mm

Most likely it is not, Seiko often uses 1.10 or 1.60mm thickness. These can be replaced with the nearest standard thickness, even taller if that is liked.

 

1 hour ago, xyzzy said:

It's crushed when the crystal is pressed in and should be replaced. But you don't always have to replace it if it's not damaged.

It's not really crushed, but slightly pressed. The most common reason of damage is unexperienced people removing it.

 

Link to comment
Share on other sites

15 hours ago, jdm said:

This info (not a secret), which  I didn't give to not further confuse the owner  - he needs to gets the watch repaired, not become a Seiko technical expert, is derived from obtaining the part number from online databases, and then decoding the P/N using the table attached. 

My purpose for providing that was to say it doesn't have an AR coating or other feature that might make generic replacement undesirable, which can be found from the P/N.  The serial number and so forth aren't useful for finding a replacement so I didn't mention them.

The thickness and large size combined might be problem for generic replacement.  I don't think it will be 1.2, too thin for 100M rating.  I would guess 1.5, 1.8, or 2.0.  1.5 or 2.0 is no problem, but 1.8 doesn't seem to be commonly sold as generic.  Esslinger has them, but only up to 36 mm.  It looks 37x1.8 can be found in sapphire on ebay, $24.

It is possible, not desirable but possible, to press a crystal in without a watch crystal specific press.  A C-clamp, or a drill press, and an appropriate stack of washers, etc.  Any number of pressing tools one might create that are more or considerably less effective.  The important parts are to press the crystal in flat.  If it gets angled at all, it will not go in properly and will jam.  And push near the outer edge of crystal.  Too much in the center and it can break.  And of course, don't scratch anything.

Link to comment
Share on other sites

On 12/28/2021 at 3:52 AM, xyzzy said:

My purpose for providing that was to say it doesn't have an AR coating or other feature that might make generic replacement undesirable.

Right. On the other hand we knew from the picture that it was a no feature crystals, because that is what is always used on affordable Seiko quartz watches.

 

On 12/28/2021 at 3:52 AM, xyzzy said:

The thickness and large size combined might be problem for generic replacement.  I don't think it will be 1.2, too thin for 100M rating. 

Worth to remember that the 100m indicated on this class of watches are only for marketing, these are not meant to be exposed more than 5 meters under water IMHO, especially when crono pusher buttons are present. When I can find it again I'll post a table of thickness/dia values to pressure which can be useful as a reference. In all events a thicker glass is desirable for an higher protection to shocks.

 

Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • although not in this case.  It was the Lugano Convention and its deficiencies that allowed a Swiss court decision in the first place.  This isnt really a Brexit issue at all.  A decision that affects both the EU and the UK should never have been heard in Switzerland. I bet the authorised service centres in the UK are pretty pleased.  It's a massive shame, though; I believe watch owners should be able to choose to have their watch serviced by whoever they trust.
    • Hi guys I think that old hippy is correct, it opens the gates for china to manufacture aftermarket spare parts. considering that they already do work on behalf of the Swiss I guess this decision gives the a little more legitimacy to tool up and I am sure they will take advantage of the situation either with or without the blessing of the Swiss watch industry  Having read about the protectionist machinations of the Swiss in the history of Europe they were the only ones to get fat at everybody else’s expense. I think the outcome could have been guessed at but ,  fair play to Cousins UK for standing up to them.  Now the question,  will everybody boycott Swiss watches and Swatch, no way they will still fill their coffers.  Me I stick with the Japanese once renowned for cheap shitty watches who came good through industrial effort and don’t for get the Russians that most dismiss as low grade crap. Wouldn’t buy a swatch product ever how about you all.? a
    • Hold the crown when in winding position, move the click away from the crown wheel, and then while holding the crown let it slowly unwind. I recollect that you must remove the automatic device bridge first, but maybe I'm wrong. You can first try without removing the automatic device bridge.
    • nevenbekriev- You nailed it with your description of me and my reaction when the clock started ticking again. I am a newbie.  I love the sound and idea of mechanical clocks but the idea of owning one and trying to keep them running has never appealed to me. My wife bought this one and an antique German wall clock.  When I looked into having someone repair them for me, the universal response was "it's really expensive to work on them, you should just replace the movement". So, I had nothing to lose, I started researching them and opened them up. The wife is happy because she hears the sound of the clocks again. But I have gone down the "accuracy" rabbit hole. In the vertical position, the balance wheel was not floating. It was sitting on the bottom of the frame. I adjusted the lower spring collet and got it floating. It easily passed the 270 degree 3 to 5 minute oscillation test. It took 8 minutes for the wheel to completely stop moving.  I put it the unit back in the movement and checked the safety pin. It does not touch the safety roller anywhere in +/-270 degrees rotation from neutral position. But the amplitude of the rotation with the spring fully wound is weak based on what you are saying. It rotates +/-90 degrees from the neutral position.  No, I did not take the movement completely apart.  That seemed way outside my skill set at the time. There is a reason I became an electrical engineer and not a mechanical engineer. I am much more comfortable with moving electrons than tiny moving metal parts. Will I do it in the long run? Anything can happen. I don't seem to be able to let it go.
×
×
  • Create New...