Jump to content

Nomos 5500


Recommended Posts

Here is a longshot. I took in a Glashutte with a C5500 movement for cleaning, before realizing that it needs a new date disk. Anyone know anywhere to purchase this part, or any parts for Nomos? The usual suspects (Cousins, Ofrei, etc.) don't seem to carry parts for them. I realize this is a shot in the dark, but I thought I would ask anyway. Thanks in advance for any help.

Link to comment
Share on other sites

Not sure what a Nomos C5500 is, but they are pretty good about making parts available to independent watchmakers and their in-house service and repair is in my experience reasonable too. If your watchmaker is cleaning the movement, he should be able to order and replace the date disc at the same time.

  • Like 1
Link to comment
Share on other sites

1 hour ago, Klassiker said:

If your watchmaker is cleaning the movement, he should be able to order and replace the date disc at the same time.

The OP is the watchmaker. Smart decision by an independent maker to supply (at least) professionals. 

  • Like 1
  • Thanks 1
Link to comment
Share on other sites

Thats great information guys, thank you. I will try to contact Nomos directly and report back. That would be absolutely amazing if they would be willing to sell parts directly.

Here is a shot of the movement if anyone is curious. IMG_2194.thumb.jpg.755a04a2b633510a45b1efd713a41420.jpg

 

 

Edited by watchfellow
Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • OK, welcome in the world of alarm clocks... I guess the 4th wheel is dished because it is from another movement. If it was not dishet, then it would not mesh with the pinion of the escape wheel, am I right? The marks of wear on the 4th wheel pinion doesn't corespond to the 3th wheel table position, at list this is what i see on the picts. Calculating the rate is easy - there is a formula - BR = T2 x T3 x T4 x T5 x 2 /(P3 x P4 x P5) where T2 - T5 are the counts of the teeth of the wheels tables, and P3 - P5 are the counts of the pinion leaves. Vibrating the balance is easy - grasp for the hairspring where it should stay in the regulator with tweasers, let the balance hang on the hairspring while the downside staff tip rests on glass surface. Then make the balance oscillate and use timer to measure the time for let say 50 oscillations, or count the oscillations for let say 30 seconds. You must do the free oscillations test to check the balance staff tips and the cone cup bearings for wear. This kind of staffs wear and need resharpening to restore the normal function of the balance.
    • Glue a nut to the barrel lid, insert a bolt, pull, disolve the glue.  Maybe someone will have a better answer. 
    • The stress is the force (on the spring) x distance. The maximum stress is at the bottom, and decreases up the arm. That's why they always break at the bottom. I used a round file, then something like 2000 grit to finish. I gave the rest of the arm a quick polish - no need for a perfect finish. Just make sure there are no 'notches' left from cutting/filing. The notches act like the perforations in your toilet paper 🤣
    • It's probably a cardinal rule for watch repair to never get distracted while at the bench. Yesterday, after finishing a tricky mainspring winding/barrel insertion (I didn't have a winder and arbor that fit very well) I mentally shifted down a gear once that hurdle was passed. There were other things going on in the room as I put the barrel and cover into the barrel closer and pressed to get that satisfying snap. But when I took it out I realized I never placed the arbor.  When opening a barrel, we are relying on the arbor to transfer a concentrically-distributed force right where it is needed at the internal center of the lid. However, when that isn't present it's difficult to apply pressure or get leverage considering the recessed position of the lid, the small holes in the barrel and the presence of the mainspring coils. It was a beat-up practice movement so I didn't take a lot of time to think it over and I pushed it out using a short right-angle dental probe placed in from the bottom, but that did leave a bit of a scratch and crease in the thin lid. I had also thought about pulling it using a course-threaded screw with a minor thread diameter smaller than the lid hole and a major diameter larger, but that may have done some damage as well.  Thinking about how this might have been handled had it been a more valuable movement, is there a method using watchmaking or other tools that should extract the lid with the least damage? 
    • 🤔 what happens if lubrication is placed directly on top of epilame ? Making a small groove so the lubrication doesn't spread across the component but what if when lubing a little overspills and sits on the epilame .
×
×
  • Create New...