Jump to content

Fitting crowns to a Smiths watch


PeterDRG

Recommended Posts

Hi

I´m Peter, a model engineer in Istria. I´m reasonably well equipped, with a Hobbymat MD65 and lots of accessories, a Hobbymat BF400 mill , a Boxford and lots of George Thomas stuff. I´m making a Chronos Wheel Engine, for which I already have the division plate and cutter head. I will be using it to make a weight driven brass alarm clock to the John Wilding design.

So much for the intro. (I couldn't get the intro page to work)

I have a Smiths wristwatch which I bought with money from my paper round 60 years ago. It is getting difficult to wind, as the crown is worn. I have a box of crowns in various sizes, but I have never worked on a watch before. Donald de Carle doesn't seem to say much about it. It is probably very simple, but I thought it safer to ask here first how to do it.

Are the destructions available anywhere, please ?

TIA

Cheers

Link to comment
Share on other sites

3 minutes ago, PeterDRG said:

Are the destructions available anywhere, please ?

Welcome here. Beginners often get associated with destructions, but I don't think that will be your case here. From our host Mark Lovick, if you want to learn practical watchmaking I recommend you enroll his training at watchfix.com

 

Link to comment
Share on other sites

1 hour ago, PeterDRG said:

 A firm grip whilst holding the stem and it will wind off ?

Don't force anything. If the crown doesn't unscrew with moderate force heat up the pipe a bit to loosen any thread locking agent that may be ther. 

Link to comment
Share on other sites

Hi  Bear in mind jdm's advice regarding force and heating it up to release thread lock. Also be reminded that watch stems have Tap numbers relating to stems and stems differ in thread diameters and taps.  The site "windingstems.com"has a co784727683_TapSizeChart.jpg.b2fcc5aa830ae6c1516aa8b2cc08caf9.jpgmprehensive list of available stems also Cousins uk.  But cousins use a differnt tap system so check your stem before ordering

Link to comment
Share on other sites

  • 2 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • I think if you want to play Billy big b.ollocks then you have to have something up your sleeve, anyone that knows how to fight, plays dirty. Lets face it a lot of folk that voted for Brexit just rolled uk their sleeves to say up yours EU hoping for good changes. We have idiots for leaders and probably none of them clever enough to clean the shitty stick they were given. I didnt vote, what will be will be.
    • I voted leave too, my reasoning was the the EU is undemocratic, no elected officials. I don't regret it but I  am sad that both sides acted like petulant toddlers.  Shameful.  I'm not on other forums but if I was and left this site, would you shun me? Of course not, we aren't petulant toddlers.  
    • This is a type of tool that may be suitable to remove the bezel - though note that I'm pretty sure the watch should be face down - not face up, as in some of the photos of these tools on amazon & ebay! If you try one one of those, put the movement screws back in first to avoid accidents. https://www.amazon.co.uk/Removal-Professional-Remover-Watchmaker-Diameter/dp/B09XCH4QVN?source=ps-sl-shoppingads-lpcontext&ref_=fplfs&smid=A296NCMMFVXSDN&th=1  
    • Hi, I’m constantly asking my wife to help me with removing the stem in order to complete casing. To expand, this is not a challenge for me when the setting lever is secured by a screw (older calibers). However when the setting lever is attached to a spring loaded setting lever axel, like on more modern calibers, I simply don’t see how to apply enough pressure on the button to get the stem out short of putting the movement face down with the dial and hands attached, which I’m loath to do in order to avoid damaging the dial/hands? what technique should I be using? thanks  
    • Many thanks for your advice (being borne in mind at present) & offer Dell. When I was given the clock the plastic anchor was loose on the arbour (it had split at the 'hole') &, after repairing this, I have been trying to determine whether the spindle (pin) should be perpendicular when the pallet is sitting on a flat surface; or whether, when installed, its L-R extremes (or alternatively its tick & tock points) should lie at equal angles from the vertical when moved with spring absent. I can get the clock to run but in every such configuration the top block has to be turned anti-clockwise (from above) by quite a bit in order to be 'in beat' & it always runs fast (despite the pendulum being set to as slow as possible). This makes me wonder if there is any particular feature of/fault in a torsion spring clock which determines which turn direction (if any) is necessary to get it 'in beat'; & whether there would be a different set of settings that would get it running nearer to time at somewhere around the mid timing/inertia position which would then allow tweaking of the fast/slow setting.
×
×
  • Create New...