Jump to content

Weishi vs. Vibrograf conflicting results

LittleWatchShop
 Share

Recommended Posts

xyzzy WRT Addict

xyzzy

Posted
Posted
On 11/11/2021 at 4:07 AM, LittleWatchShop said:

So...how does this thing work?  Well, the motor spins at a precise speed.  The motor drives a roller that his a raised spiral.  When the watch ticks, it causes a hammer to impact the roller.  If the impact hammer hits the roller at the same angular position each time, a vertical line will be marked on the paper.  If the impact hammer hits the roller at a different angular position, the line will walk to the left or to the right. 

From the photo of the tape of a watch running slow, I gather that the motor spins from right to left?

Link to comment
Share on other sites
nickelsilver Distinguished Member

nickelsilver

Posted
Posted
52 minutes ago, xyzzy said:

From the photo of the tape of a watch running slow, I gather that the motor spins from right to left?

I'm sure the motor runs in a circle.

 

Sorry, haha. I haven't run my b200 in many years, as I recall looking down at the roller, with the upper part of the spiral to the left, it continues downward towards the right.

Link to comment
Share on other sites
LittleWatchShop Distinguished Member

LittleWatchShop

Posted
  • Author
Posted
27 minutes ago, nickelsilver said:

I'm sure the motor runs in a circle.

 

Sorry, haha. I haven't run my b200 in many years, as I recall looking down at the roller, with the upper part of the spiral to the left, it continues downward towards the right.

That is correct. It is a raised helix. Very clever design.

Link to comment
Share on other sites
JohnR725 Distinguished Member

JohnR725

Posted
Posted
53 minutes ago, LittleWatchShop said:

is the 5meg board from a B200a?

Absolutely no idea at all?

Went back to the folder where the photograph was found and the only thing I photographed was that office later board and the serial number plate. At least I'm guessing that would be the machine it came from.

B200 sn for new osc.JPG

Link to comment
Share on other sites
LittleWatchShop Distinguished Member

LittleWatchShop

Posted
  • Author
Posted (edited)
18 minutes ago, JohnR725 said:

Absolutely no idea at all?

Went back to the folder where the photograph was found and the only thing I photographed was that office later board and the serial number plate. At least I'm guessing that would be the machine it came from.

B200 sn for new osc.JPG

The one I have...guessing my Dad bought it in the early 70s. Before that, he had a Watchmaster.

when I get back home, I plan to measure the speed of the motor, and check to see which crystal board I have.

Edited by LittleWatchShop
Link to comment
Share on other sites
xyzzy WRT Addict

xyzzy

Posted
Posted
On 11/12/2021 at 10:59 AM, nickelsilver said:

Sorry, haha. I haven't run my b200 in many years, as I recall looking down at the roller, with the upper part of the spiral to the left, it continues downward towards the right.

That's the opposite of what I thought.  But, the tape moves "up", I was thinking down, so from the left to the right.  So the line will move to the right as it goes down if the movement is slow.

Link to comment
Share on other sites
LittleWatchShop Distinguished Member

LittleWatchShop

Posted
  • Author
Posted

OK, indeed the motor spins at the following speeds: 32, 40, 44, 48 RPS.  I verified this by measuring the motor pulses with an oscilloscope.

The gear ratio to the platen (the rotating cylinder) is 2.666:1 (the motor turns 2.3333 times for every rotation of the platen).

There are two oscillations of the helix on the platen for every rotation, thus the effective gear ration with respect to the helix is 1.333:1

Taking the ratio of the motor speed to the helix frequency yields 24, 30, 33, 36 which are the values at the top of the beat table on the B200 and designated as "N" in the document posted above. 

These numbers comport with the numbers I posted originally where I assumed that the platen and the helix were 1:1 and the motor to platen also 1:1

And finally, the divider values to achieve the motor frequencies are 330, 264, 240, 220.

There is harmony in the universe.  I can now move on to the next problem...

Link to comment
Share on other sites
JohnR725 Distinguished Member

JohnR725

Posted
Posted

I was probably making a incorrect assumption which was that the vacuum tube version the B100 probably Has the same print mechanism but I don't know if it really does.

What's interesting about the company who makes the timing machine is that the earlier versions they have schematics and repair Manual with all the variations of the schematics and a complete parts list which is not entirely helpful as some of the parts a course or their part numbers and do not correspond to anything in the real world. Like for instance the crystal pickup.

What I was curious about was whether the a use the same quartz frequency they did not. Then because it's vacuum tubes they use a three stage divider and came up the frequencies that I snipped out down below.

 

B100 _motor fr.JPG

Link to comment
Share on other sites
JohnR725 Distinguished Member

JohnR725

Posted
Posted
29 minutes ago, LittleWatchShop said:

I don't understand what this snip means. 

It means I was being lazy and only snipped out one item and didn't give you the other item which I'm now giving you. What the snippet shows you is the final frequency used to drive the motor. Maybe this one is better because it shows you the crystal frequency and what each stage would divide down to to get the final motor frequency.

B100 frequency division for motor drive.JPG

Link to comment
Share on other sites
JohnR725 Distinguished Member

JohnR725

Posted
Posted

Out of curiosity would you be interested in any other schematics of timing machines? For instance I have the schematic with waveforms for the Bandelin  Tickoprint perfect  T46 Timing machine it looks like it's from the year 1970 at least the schematic the interesting machine with an integrated circuit or two but a complete transistor dividing circuitry

Link to comment
Share on other sites
LittleWatchShop Distinguished Member

LittleWatchShop

Posted
  • Author
Posted
2 hours ago, JohnR725 said:

Out of curiosity would you be interested in any other schematics of timing machines? For instance I have the schematic with waveforms for the Bandelin  Tickoprint perfect  T46 Timing machine it looks like it's from the year 1970 at least the schematic the interesting machine with an integrated circuit or two but a complete transistor dividing circuitry

Would love to!!!!!

Link to comment
Share on other sites
LittleWatchShop Distinguished Member

LittleWatchShop

Posted
  • Author
Posted
8 hours ago, JohnR725 said:

Rather than just the schematic yet the entire manual. Complete with it's very interesting interpretation a waveforms at the very back the schematics.

Very nice!  The Tickoprint operates on the same principle as the Vibrograf.

Clever way to get a lot of gain at high frequencies with a single opamp stage.  Back then opamps were expensive...today they are essentially free.

Link to comment
Share on other sites
  • 10 months later...
LittleWatchShop Distinguished Member

LittleWatchShop

Posted
  • Author
Posted (edited)
13 minutes ago, DavidinSB said:

Hi. It looks like you're simulating the circuit using LTSPice. Did you ever get that simulation to work?  Frequency response curves? I need to determine why the difference in results of my Weishi vs. Vibrograf.

Yes...LTSpice. I can send files if you want to fiddle around...tomorrow.

As I recall, they did work.

I picked up another Vibrograf the other day with microphone. The main unit does not work, but I bought it for the mic

Edited by LittleWatchShop
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Hawaiikook808
      Balance spring fell out of regulator pin.

      By Hawaiikook808 · Posted

      Thank you so much, Hector and CJ. I appreciate the tech sheet and the video. Gasp, I think I will make the attempt. What's the worst that can happen? I think there may be a new balance complete in my future, though.  I'll update the post and let you know the result. R, Frank  
    • Waggy
      Movement holder made with 3D printer

      By Waggy · Posted

      So here is the new base (v 2.1), I made it so that the base will fit over and swallow the stump of the hand pusher tool (or at least my clone of the tool), I also reduced the OD of the bottom skirt a little as it looked/felt a little large, here are a few pictures and the fake .pdf file which you need to convert to .zip once downloaded.   The cut-out seen on the below image on the bottom of the base should swallow the OD (40 mm, +0.1 mm tolerance) of the stump and the height of the stump 9.5mm (measured to 9.1mm, but rounded to 9.5mm) - let me know if this works for your tool.   Note, I think you may need to print supports for the new internal shelf created? Here is the fake .pdf for just the FreeCAD base file and 3mf files Modular Movement Holder.pdf Here is the fake pdf for complete set of the new base and ring FreeCAD/3mf files: Modular Movement Holder base and ring v 2.1.pdf However, I'm wondering how often you could use this feature, adding the dial usually increases the OD of the movement, so you would need a new (larger) adapter ring tuned to the OD of the dial and I wouldn't like to grip the dial in any kind of movement holder if It could be avoided for fear of damaging it. Maybe I'm misunderstanding you?
    • HectorLooi
      Balance spring fell out of regulator pin.

      By HectorLooi · Posted

      Hi Frank, you have dived headlong into the deep end. Hairspring work has to be the scariest thing a newbie has to tackle. Your hairspring appears to be bent and just putting it back into the regulator would not allow the balance to work properly. It might start oscillating but the performance would not be good. The proper thing to do is to unstud the hairspring, remove the hairspring from the balance, reinstall the hairspring on the stud carrier, reshape the endcurve and centre the collet to the balance jewel hole. This challenge would either make you or break you. Hope that you will be able to fix your watch. Welcome to the world of watchmaking.  Watch this video. It think it'll give you an idea of the task ahead. From your 1st photo, I think you have a etachron type stud. Let me see if I can find a video on how to remove it from the arm.
    • Curare
      Balance spring fell out of regulator pin.

      By Curare · Posted

      Have read of the Tech Sheet attached on the balance section page 12. It may be bent but until you reposition it back in the regulator pins you'll never know. Cheers CJ 4R35B_4R36A.pdf
    • Hawaiikook808
      Balance spring fell out of regulator pin.

      By Hawaiikook808 · Posted

      Aloha All, My Seiko 4R35B movement stopped working today. Upon closer inspection, it looks like the balance spring came out of the regulator pin. This is my first time working on a balance. Any advice on how to get this spring repositioned (back to normal)? I'm pretty sure that while adjusting the beat error on this movement, I must have turned the stud (I didn't even know they turned), and the spring eventually fell out.  Will the spring go back to even spacing when it's back in the pin, or does it look bent? Thanks, Frank  
×
×
  • Create New...