Jump to content

Weishi vs. Vibrograf conflicting results


Recommended Posts

On 11/11/2021 at 4:07 AM, LittleWatchShop said:

So...how does this thing work?  Well, the motor spins at a precise speed.  The motor drives a roller that his a raised spiral.  When the watch ticks, it causes a hammer to impact the roller.  If the impact hammer hits the roller at the same angular position each time, a vertical line will be marked on the paper.  If the impact hammer hits the roller at a different angular position, the line will walk to the left or to the right. 

From the photo of the tape of a watch running slow, I gather that the motor spins from right to left?

Link to comment
Share on other sites

52 minutes ago, xyzzy said:

From the photo of the tape of a watch running slow, I gather that the motor spins from right to left?

I'm sure the motor runs in a circle.

 

Sorry, haha. I haven't run my b200 in many years, as I recall looking down at the roller, with the upper part of the spiral to the left, it continues downward towards the right.

Link to comment
Share on other sites

27 minutes ago, nickelsilver said:

I'm sure the motor runs in a circle.

 

Sorry, haha. I haven't run my b200 in many years, as I recall looking down at the roller, with the upper part of the spiral to the left, it continues downward towards the right.

That is correct. It is a raised helix. Very clever design.

Link to comment
Share on other sites

53 minutes ago, LittleWatchShop said:

is the 5meg board from a B200a?

Absolutely no idea at all?

Went back to the folder where the photograph was found and the only thing I photographed was that office later board and the serial number plate. At least I'm guessing that would be the machine it came from.

B200 sn for new osc.JPG

Link to comment
Share on other sites

18 minutes ago, JohnR725 said:

Absolutely no idea at all?

Went back to the folder where the photograph was found and the only thing I photographed was that office later board and the serial number plate. At least I'm guessing that would be the machine it came from.

B200 sn for new osc.JPG

The one I have...guessing my Dad bought it in the early 70s. Before that, he had a Watchmaster.

when I get back home, I plan to measure the speed of the motor, and check to see which crystal board I have.

Edited by LittleWatchShop
Link to comment
Share on other sites

On 11/12/2021 at 10:59 AM, nickelsilver said:

Sorry, haha. I haven't run my b200 in many years, as I recall looking down at the roller, with the upper part of the spiral to the left, it continues downward towards the right.

That's the opposite of what I thought.  But, the tape moves "up", I was thinking down, so from the left to the right.  So the line will move to the right as it goes down if the movement is slow.

Link to comment
Share on other sites

OK, indeed the motor spins at the following speeds: 32, 40, 44, 48 RPS.  I verified this by measuring the motor pulses with an oscilloscope.

The gear ratio to the platen (the rotating cylinder) is 2.666:1 (the motor turns 2.3333 times for every rotation of the platen).

There are two oscillations of the helix on the platen for every rotation, thus the effective gear ration with respect to the helix is 1.333:1

Taking the ratio of the motor speed to the helix frequency yields 24, 30, 33, 36 which are the values at the top of the beat table on the B200 and designated as "N" in the document posted above. 

These numbers comport with the numbers I posted originally where I assumed that the platen and the helix were 1:1 and the motor to platen also 1:1

And finally, the divider values to achieve the motor frequencies are 330, 264, 240, 220.

There is harmony in the universe.  I can now move on to the next problem...

Link to comment
Share on other sites

I was probably making a incorrect assumption which was that the vacuum tube version the B100 probably Has the same print mechanism but I don't know if it really does.

What's interesting about the company who makes the timing machine is that the earlier versions they have schematics and repair Manual with all the variations of the schematics and a complete parts list which is not entirely helpful as some of the parts a course or their part numbers and do not correspond to anything in the real world. Like for instance the crystal pickup.

What I was curious about was whether the a use the same quartz frequency they did not. Then because it's vacuum tubes they use a three stage divider and came up the frequencies that I snipped out down below.

 

B100 _motor fr.JPG

Link to comment
Share on other sites

29 minutes ago, LittleWatchShop said:

I don't understand what this snip means. 

It means I was being lazy and only snipped out one item and didn't give you the other item which I'm now giving you. What the snippet shows you is the final frequency used to drive the motor. Maybe this one is better because it shows you the crystal frequency and what each stage would divide down to to get the final motor frequency.

B100 frequency division for motor drive.JPG

Link to comment
Share on other sites

Out of curiosity would you be interested in any other schematics of timing machines? For instance I have the schematic with waveforms for the Bandelin  Tickoprint perfect  T46 Timing machine it looks like it's from the year 1970 at least the schematic the interesting machine with an integrated circuit or two but a complete transistor dividing circuitry

Link to comment
Share on other sites

2 hours ago, JohnR725 said:

Out of curiosity would you be interested in any other schematics of timing machines? For instance I have the schematic with waveforms for the Bandelin  Tickoprint perfect  T46 Timing machine it looks like it's from the year 1970 at least the schematic the interesting machine with an integrated circuit or two but a complete transistor dividing circuitry

Would love to!!!!!

Link to comment
Share on other sites

8 hours ago, JohnR725 said:

Rather than just the schematic yet the entire manual. Complete with it's very interesting interpretation a waveforms at the very back the schematics.

Very nice!  The Tickoprint operates on the same principle as the Vibrograf.

Clever way to get a lot of gain at high frequencies with a single opamp stage.  Back then opamps were expensive...today they are essentially free.

Link to comment
Share on other sites

  • 10 months later...
13 minutes ago, DavidinSB said:

Hi. It looks like you're simulating the circuit using LTSPice. Did you ever get that simulation to work?  Frequency response curves? I need to determine why the difference in results of my Weishi vs. Vibrograf.

Yes...LTSpice. I can send files if you want to fiddle around...tomorrow.

As I recall, they did work.

I picked up another Vibrograf the other day with microphone. The main unit does not work, but I bought it for the mic

Edited by LittleWatchShop
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Getting back to the issue which is us guys repairing or just enjoying horological exploits. The big worry now is how sound is Cousins as company going forward. The of cost if this 8 year legal battle will be astronomical. Cut backs will happen noticed already how the Cousins catalogue is half its size this year. The main supplier going out of business will hit the UK horological community in a big way.    On the Brexit issue it was about a sovereign country being able to make its own laws and trade with any country in the world. I cannot see what was wrong with this. For those who wish to re join the cost would be very high indeed.
    • Yes, it's the same (old) song and it's getting worse & worse;  
    • 🤔 leaving the EU meant that UK was no longer part of the convention and have already been turned down an independent reapplication. I'm pretty sure courts have to be held in Switzerland in this case. There will be a lot more watches stashed away in draws  tbh, folk wont be able to afford to maintain them. Cheap watches will be bought and top end watches by folk with plenty of cash that can pay for service and repair. The expensive once in a lifetime gifts and everything else inbetween will be at the forgotton when they stop working. I know i was being a numpty, get used to it 😄 Anybody that knows will boycott them, but besides repairers who will know. Nope will never buy one, i made that decision as soon as i learnt about this. 
    • although not in this case.  It was the Lugano Convention and its deficiencies that allowed a Swiss court decision in the first place.  This isnt really a Brexit issue at all.  A decision that affects both the EU and the UK should never have been heard in Switzerland. I bet the authorised service centres in the UK are pretty pleased.  It's a massive shame, though; I believe watch owners should be able to choose to have their watch serviced by whoever they trust.
    • Hi guys I think that old hippy is correct, it opens the gates for china to manufacture aftermarket spare parts. considering that they already do work on behalf of the Swiss I guess this decision gives the a little more legitimacy to tool up and I am sure they will take advantage of the situation either with or without the blessing of the Swiss watch industry  Having read about the protectionist machinations of the Swiss in the history of Europe they were the only ones to get fat at everybody else’s expense. I think the outcome could have been guessed at but ,  fair play to Cousins UK for standing up to them.  Now the question,  will everybody boycott Swiss watches and Swatch, no way they will still fill their coffers.  Me I stick with the Japanese once renowned for cheap shitty watches who came good through industrial effort and don’t for get the Russians that most dismiss as low grade crap. Wouldn’t buy a swatch product ever how about you all.? a
×
×
  • Create New...