Jump to content

What do you think of this overpriced piece of ugliness?

oldhippy

By oldhippy
in All Things Clocks

 Share

Recommended Posts

spectre6000 Distinguished Member

spectre6000

Posted
Posted

I think the UK is pretty well known for staid taste, and this ain't that; probably explains some of the reaction. As a woodworker, I can appreciate the use of wood and grain. Even with thousands of dollars in exotic woods stashed in a room in my basement, I have to say it's a bit busy for me for the piece. Some people will dig the natural beauty of it though.

Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
  • Author
Posted
2 hours ago, spectre6000 said:

I think the UK is pretty well known for staid taste, and this ain't that; probably explains some of the reaction. As a woodworker, I can appreciate the use of wood and grain. Even with thousands of dollars in exotic woods stashed in a room in my basement, I have to say it's a bit busy for me for the piece. Some people will dig the natural beauty of it though.

It's German.

  • Like 1
  • Haha 1
Link to comment
Share on other sites
Tmuir Distinguished Member

Tmuir

Posted
Posted

I could see the movement was German and not a lot of age to it.

I'm not 100% sure but I think the pendulum is in the open which means any drafts would impact the clocks timekeeping.

I agree that great quality of skill has gone into making the case, but its too busy for me and the dial doesn't do much for me either.

Link to comment
Share on other sites
KarlvonKoln Distinguished Member

KarlvonKoln

Posted
Posted
On 10/19/2021 at 12:10 PM, oldhippy said:

Considering the movement is nothing to write home about the seller has priced it due to that case. The bottom part of the case is completely out of proportion to the top. Which to me makes it look hideous.

I gotta say, it does rather look like someone tried to perch a grandmother (or some other large wall...) clock on top of a plinth that was a tad too large, then added a couple spindles to hold it up.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • oldhippy
      Movement inserted from crytal side

      By oldhippy · Posted

      Before putting it back in the case I would fit the hands and use a pin vice on the stem to make sure the hands were in line. 
    • Jon
      Introducing myself

      By Jon · Posted

      Hi there  
    • Jon
      Movement inserted from crytal side

      By Jon · Posted

      Put the movement in a movement holder and it will be supported as you push down on the setting lever post to release the winding stem. Make sure the post is over the shoulder of the movement holder so what you are pressing down on is supported. As a general rule, hold the movement and not the movement holder. Replace the hands when the movement isn't in the case and support the centre jewel (if it has one) on a hard surface or staking block when replacing the hands to stop the jewel accidentally moving or even coming out. A dedicated movement holder with a central jewel support is even better, but pricey
    • JohnR725
      Main spring

      By JohnR725 · Posted

      It might help us if we knew which watch like model number.
    • Zedster
      Movement inserted from crytal side

      By Zedster · Posted

      Hi, guys I have a bit of a predicament and hopefully, somebody can advise. I'm working on a Roamer MST 521 where the movement is extracted from the crystal side. I'm now at the final hurdle where I need to replace the movement back into its case but I'm not sure of the correct procedure. I still need to fit the hands but that's where the problem lies. If I insert the winding stem to test the hands for correct alignment I will need to turn the movement over to release the stem again it's the spring-loaded type and needs a small bit of force to push down but with the hands fitted, I don't think I can do this on a cushion without causing some damage to the hands and that's the last thing I want to do, this watch has already been a love-hate relationship and I'm so close to boxing this one off which I'm counting as my first major project.  The other option is to case the movement then fit the hands and hope everything is okay. I've already broken the original winding stem but managed to find a replacement, the last one in stock, so I'm a bit reluctant to keep removing it. Any suggestions would be appreciated. 
×
×
  • Create New...