Jump to content

Elma Watch Cleaning Machine

SSTEEL
 Share

Recommended Posts

SSTEEL Distinguished Member

SSTEEL

Posted
  • Author
Posted (edited)

Cheers Mark, so I have wired the lamp up wrong by the looks of it, can you tell me which is heat on, and hear off' position?  Left off, right on?

 

Heat is on with my switch to the right, but in this position I cannot get the motor to spin, its only spinning with the heat switched to the left, heater off.

 

Ah, it works when pushed down, and baskets in the heater chamber though :)

Edited by SSTEEL
Link to comment
Share on other sites
  • Replies 637
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

LittleWatchShop
LittleWatchShop

I didn't get it. I am on a Levin lathe binge. Turning my small fortune into a smaller one

SSTEEL
SSTEEL

Its ok now, I have source one, should anyone else need a copy drop me a pm.

SSTEEL
SSTEEL

Had a few messages about the wiring diagram, so uploaded it for all to see..   super elite wiring diagram by Micky.!, on Flickr

Posted Images

Mark Distinguished Member

Mark

Posted
Posted

Yes the heater and light should come on when the heater switch it flicked from left to right.

The motor is independent and comes on regardless of wether the heater is on or not.

Unless the heater is on, then no light appears when the motor is switched on.

Hope this helps.

  • Like 1
Link to comment
Share on other sites
SSTEEL Distinguished Member

SSTEEL

Posted
  • Author
Posted

Ok, that certainly helps, I need to recheck the lamp  wiring, as I have obviously missed something, and wired it up wrong, but at least everything is working as it should be, except the light, I will check the bulb first, as I have a new one here to fit.

Link to comment
Share on other sites
SSTEEL Distinguished Member

SSTEEL

Posted
  • Author
Posted (edited)

Fitted the digital timer, but not exactly how iI planned, I removed the wide cone shaped base which was screwed on.

 

15884799157_c9e40236eb.jpgUntitled by Micky.!, on Flickr

 

And would you believe it, when my curiosity got the best of me, I trial fitted the timer into the circular void, and it was as if it was made to measure, it even clicked into place firmly, and is now good to go, it sits proud, so I will see how I get on with it, I can always fit it behind the face plate at a later date should I want to.

 

15450894753_e16c2235ca.jpgUntitled by Micky.!, on Flickr

 

16070561315_b61ba7249f.jpgUntitled by Micky.!, on Flickr

Edited by SSTEEL
Link to comment
Share on other sites
bobm12 Distinguished Member

bobm12

Posted
Posted

I knew that new knob would just do it! Only kidding! :)

 

This is an awesome project and the result exceeding expectations...or maybe not?, considering the attention to detail, care, money, time and amount of work and preoccupation you put into it, Micky! Superlative results!

 

All I'm expecting now is for it to lift off and travel to the next galaxy...but then you will be getting the Nobel Price in Rocket Science not in Horology which is not the same thing and not that desirable anyway! Congratulations on a perfect executed restoration and, wow, amazing results!

 

My most heartfelt congratulations,

 

Cheers,

 

Bob

  • Like 1
Link to comment
Share on other sites
bobm12 Distinguished Member

bobm12

Posted
Posted

I figured it would Micky, and proud of your achievement. Very few people would have done such a thorough job! It has been a real labor of love and the results better than the original! 

 

Any project in mind? I'd love to see how the parts come out! Please, take some before and after pics. Of course, I understand that cleaner types have a bearing in the outcome and you will probably be experimenting to obtain optimal results...just as I do! Does it ever ends? I hope not since the fun will be over!

 

Cheers,

 

Bob

  • Like 1
Link to comment
Share on other sites
SSTEEL Distinguished Member

SSTEEL

Posted
  • Author
Posted

I will be carrying out some test cleaning first before I start cleaning a complete movement, I want to get a feel for the machine, and see the results so I know what to expect, and what it can do for me.  I hope that makes sense?  Yes, I could throw any number of disassembled movements I have ready for cleaning, but I do want to test it out first, my curiosity needs satisfying :)

  • Like 1
Link to comment
Share on other sites
SSTEEL Distinguished Member

SSTEEL

Posted
  • Author
Posted (edited)

Thats my thinking Mark.  Although the blue basket frame fits the old Elma holder, it's fiddly to fit, and remove the basket each time, so may as well get the matching holder.

 

Seasons Greetings to you and your family Mark.!

 

Hows your workshop relocation going btw?

Edited by SSTEEL
Link to comment
Share on other sites
SSTEEL Distinguished Member

SSTEEL

Posted
  • Author
Posted

Sounds like you need to build yourself a shed then Mark.  I have pretty much got my workshop just how I like it now, but we have to move out of aour apartment in April for a remodel, and need to set up in our temporary apartment, and then move back into our home in July, really really not looking forward to this move, I can tell you that much!

Link to comment
Share on other sites
SSTEEL Distinguished Member

SSTEEL

Posted
  • Author
Posted

Hope you all had a fab Christmas.  I finally got round to fitting my new Elma basket retainer, and oh boy, (Sam Beckett voice), it was not a straight bolt on fit.  That's what I first thought, but after some light sandpapering the motor shaft after removing the old retainer, some added grease, I was then able to slide the new retainer on, but it would not go all the way onto the shaft.  

 

What I ended up having to do is to place a small metal die on top of the heater chamber lid, lower down the shaft and new retainer ensuring the springs were free of the die, and then gently tapped the shaft from the top until it was in the correct position on the shaft, which as you know is very important for jar depth clearance.

 

Anyway, onto some photos, I know you all like photos, myself included :)

 

Old retainer removed.  (If anyone wishes to buy this, drop me a pm).

 

15962092350_9ea7d64da0.jpgUntitled by Micky.!, on Flickr

 

Then the new one fitted.

 

15527067434_2819511625.jpgUntitled by Micky.!, on Flickr

 

15961963488_6b94c2717a.jpgUntitled by Micky.!, on Flickr

 

And basket trial fitted..

 

15963337989_23a6e2f0f1.jpgUntitled by Micky.!, on Flickr

 

We had another foot of snow overnight, and its still snowing out, temps got down to -18, but that was it for now, its +3 today, and the snow is wet.  March and April is when we get the real cold, -35 :)

 

May I take this opportunity to wish each and every one of you all the very best for 2015.!

  • Like 1
Link to comment
Share on other sites
  • 3 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • watchweasol
      Chronograph Pusher Rod for EB8371-67 Snapped and Stuck in Button. Can't Unscrew.

      By watchweasol · Posted

      Hi. Yes I get it , the slot in the end I’d to allow you to screw the button on whilst holding the pusher shaft. To remove the pusher tube you will need a tool such as the one shown by Richard. I think Ali Express the Chinese Amazon has replicas of the Horotec system for a lot less money, how effective they are not having had to use one. But as you said the way to go is complete removal and replacement, bodging it up will  lead to a repeat failure
    • JohnR725
      Notifications

      By JohnR725 · Posted

      It does look like it seems to be working again I'm getting emails.
    • JohnR725
      30T2 adjustment of timing washers

      By JohnR725 · Posted

      One of the things that I've been bothered with lately is timekeeping? For instance a 90-year-old pocket watch what so to timekeeping was it supposed to keep? They publish railroad timekeeping but I don't know how well normal non-railroad watches were supposed to keep time. The reason why the question comes up for me is I spend a lot of time at work adjusting watches to keep really really good time  because I have to please my boss where as when the watch was made I have to wonder what kind timekeeping would've been acceptable. After all they typically didn't have timing machines 100 years ago and they were timing and six positions certainly not for the non-railroad grade watch. On the other hand I do get paid by the hour so maybe I shouldn't be concerned of how much time I Spend trying to make everything keep chronometer timekeeping almost. Citing a Delta of 40 seconds for a 90-year-old watch is quite outstanding.
    • JohnR725
      Is this pallet fork over-locking?

      By JohnR725 · Posted

      That's an interesting question which I don't think I've seen explained anywhere. But I think the problem will go away just about instantaneously. In other words the  coating is really thin and it should go away almost immediately. So the problem should resolve itself extremely fast.  
    • VWatchie
      Is this pallet fork over-locking?

      By VWatchie · Posted

      I experienced that different types of shellac and their ages are affected differently by IPA. Sometimes the shellac dissolves in a few seconds and sometimes several minutes are required. Nowadays I never let shellac come into contact with IPA. It's a hotly debated topic here on WRT if you search. Like John, I don't think you need to worry about the weight of the shellac, but instead that it might start rubbing against something. When I learned how to adjust pallet stones, I tried documenting my experiences in this thread. Hopefully, it can help you. I personally don't believe in the idea of abrading the epilame before oiling so I don't think you need to think or worry about it. The only time I've heard anyone mention this is Alex on the YouTube channel Watch Repair Tutorials but actually no one else. I'm not saying it's "wrong" just that I don't think it's necessary or adds anything.
×
×
  • Create New...