Jump to content

Making Bracelet End Links


Recommended Posts

I have several vintage watches with twisted, bent or warped end links. I also have some nice vintage bracelets that are missing the end links completely. Some of them are rare enough that finding replacements is out of the question.

Case in point: my gorgeous ‘73 Pencron. Both end links were damaged, but one was terrible. I made a new end link for it tonight using 0.3mm SS and mandrels I made from 3mm, 6mm and 8mm square stock. I’ll replace the other eventually, but it’s not bad.

The mandrels that I made will allow me to make a wide variety of end links and eventually, my own SS bracelets. 😉
 

Pictured is the old beat up link and the new one, installed.

9C411EAF-CEE6-42CB-8732-EAC32C766432.jpeg

D20413F0-1D8A-4BF4-A9D8-49BA5A4CE5EA.jpeg

Edited by PinLeverPete
  • Like 6
Link to comment
Share on other sites

As this isn’t really a “walkthrough”, I’ll just post some pics and descriptions here. You can fill in the blanks 😉

Here is a picture of tonight’s project and it’s original bent and scratched end link:

E773829E-434B-4340-8271-FE1E7BC175E6.thumb.jpeg.dd5a12ba7b23ed34f9a7d7a68493d218.jpeg

 

The end product will basically be a piece of rectangular SS tubing with a butt or lap seam at the back (or could have the ends tucked into a “B” shape, etc...I started mandrels for this, but probably won’t pursue that route as it’s over-complicated).

The key is keeping the face clamped flat, so it won’t warp, while making the bends. That, and making the last bend on the bracelet. You can’t bend it back without warping.

Cut your SS larger than needed: measure the width of your lugs, then add 2-4mm. Cut a strip about 2cm long and the width needed.

7ABCA464-E0B6-43E7-8479-0D9CA9FDB75C.jpeg

31640648-5AFA-4BF3-ABB2-66290F2C9922.jpeg

Edited by PinLeverPete
  • Like 1
Link to comment
Share on other sites

Bend the strip around your mandrel (I am currently using 3/16”, AKA 4.65mm, square stock from Lowe’s and it has been perfect for end links).

Clamp the SS (at the midpoint and perpendicular to the length) in between your mandrel and a flat hard metal surface and bend one flap over (don’t clamp too hard or you’ll damage the metal). Press down hard with a flat metal tool (flat head screwdriver?) to get those bends sharp. I actually rolled mine flat with a large spark plug socket. Fast and easy.


Trim the flap end so that it is even with the end of the mandrel.

Flip the piece over, then clamp, bend and cut the other side the same way. 

The end result will be a “C” channel. I found that I got the best 90 degree bends using my bench vise with the knurled jaw flipped around so the flat side is facing the piece. 

 

EED1108E-DD6C-4052-88E0-5393486CD22F.jpeg

Edited by PinLeverPete
Link to comment
Share on other sites

Note: all cutting is done with a Dremel and 420 cutoff wheels. Snips, etc cannot be used as they will bend and warp the SS.

This next mandrel is the same stock, cut down to 2mm thick (not great looking, but proof of concept).

Move the piece to this mandrel and wrap the flaps around the rear, leaving one flap at 45 degrees (this will be the bracelet side). Again, press down hard with a flat metal tool to get those bends sharp.

Like I said, not pretty, but the end result...

This can also be done with $2 Walmart clamps and a larger piece of stock if you don’t have a vise.

 

 

F55830C8-D4AA-48DB-BA90-F61C8452CCCA.jpeg

11ED6315-04BC-4616-8B45-6E1FE5B46609.jpeg

Edited by PinLeverPete
Link to comment
Share on other sites

Remove from the mandrel, make one end perfectly square using the Dremel disc face or other flat. Measure off of your square end to cut and square the other side to exactly your lug width.

Cut a slot on the rear of the link on the lug side for removing the spring bars in the future.

 

BA6C6BF4-7AF2-41E9-99FB-6E43E65ED5EC.jpeg

08C7DF65-6925-4E27-A8BE-A4C8938D24E4.jpeg

Edited by PinLeverPete
Link to comment
Share on other sites

At this point, you would trim the bracelet side, but I didn’t need to with this one.

Clean up flashing, file edges lightly, round corners and finish by removing blemishes from the face with 600-1000 grit in even, parallel strokes for a brushed finish. Follow up with metal polish, only if you want a mirror/chrome-like finish.

For two tone, mask your brushed areas and polish the rest. 😉
 

Slide your 45 degree flap trough the bracelet slot and carefully bend the flap shut so that you don’t warp the face (if you want a curved face, gently squeeze the ends of the link with pliers to bow the face out...this is tricky at first).

You only get one shot at it. If you try to open it back up, you will warp it. Do it right the first time. 😉

Sanded piece is pictured on the left, unfinished on the right.

F5BA5069-714D-4ACA-87FC-076A372E0EC1.jpeg

1E8E3421-996D-4497-9F59-8ECFD8FDDBF5.jpeg

Edited by PinLeverPete
  • Like 2
  • Thanks 2
Link to comment
Share on other sites

My tools could be more refined. I’m working on that. This was really more of a “proof of concept” trial that turned out very well. 

If someone were so inclined, they could make mandrels with different face and/or rear profiles to make them curved, etc. I started work on several, but the square mandrel has worked so well and easy that I doubt I’ll pursue more complex profiles anytime soon.

If anyone has anything to add or other ideas, please post them and your results. 🙂

Edited by PinLeverPete
  • Like 1
Link to comment
Share on other sites

I just did this on a whim the other day and am a bit embarrassed about my “tools and supplies”. The square stock was purchased at Lowe’s for around $2 per piece and the SS I found at...ummm...Walmart. 

I just walked around with my calipers in hand looking for SS. Found lots of nice, low cost stuff that I’ll be able to make my own rally bracelets out of. The SS I’m using here came from a $7 small trash can (it was a 0.3mm veneer on the lid, so the can is still useable = free SS).

I’d had the idea for a while, but was finally motivated by my sad looking Pencron end link staring back at me.

 

072A1EDB-F87C-4F87-A979-188887BFBFB9.jpeg

  • Like 5
Link to comment
Share on other sites

  • 2 weeks later...
  • 2 weeks later...
  • 3 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Dell fancy a challenge🤣   https://www.ebay.co.uk/itm/285785684626?itmmeta=01HT29WVJY21Q94C73GYHGBTFX&hash=item428a277a92:g:15YAAOSwNRVmBAUz&itmprp=enc%3AAQAJAAAA0DIe4QLQBW66rSyIMiyBuk8GY%2B86pQ%2BQnxGbcNq7egAGe5DIs9YMmiWJIbZtMSxwNJIiJxuojbq523IeUSBQ6pJEIQ0tfz2ChrBR03BksmKINyklg1IK4GAfAcYY9Hta9wVeSZSZN7ZCNAfZTgKs9c4%2BUIUZ3Qjc3QjUXDn2uPRo1FiYOEewMG5A26EXb%2BclBgrqtbOmM6P3bea%2F8ZImOAXNI1HtbmtMk84pIGoM6ISwaM1PKFuADtTFMccS5e3ZjndCbXYXHrW3CecsV0edw3M%3D|tkp%3ABk9SR8q588nQYw Darwin’s theory of evolution has not been proven to be absolutely.  😀 
    • A already know the size movement I have the problem is the dial a had purchased has a dimension 20.6mm wide a want to find a watch case that going to fit the dial perfectly 
    • Hi.  I would like to take issue here regarding battery driven , watches, clocks,etc. I will and do repair these clocks in fact I have sever al in my collection as well as the regular mechanical ones. I have one on my mantle piece over 60 years old tha belonged to my wife’s Aunt,  long gone Iam afraid and it has been cleaned etc and never missed a beat and is accurate. Every one has their preduices as regards Electrical /electronic Horology but I regard it as part of the progress time line of the art of Horology and to be treated as such. Like Darwin’s theory of evolution it evolved.  Two cavemen knocking rocks together and a shard broke off , looking at it he worked out if it was stuck on the end of a stick he would have a spear. Likewise his pal seeing what he was up to picked up a piece  and did the same, now that’s evolution. Some clockmaker decided to build a clock that ran with a battery and no spring to wind up and break, progress and both the mechanical and battery driven clocks evolved, the battery ones got better to the point that if it broke you changed the complete unit. Likewise watches did the same but both can be repaired by people who approach Horology with an open mind without preduice.  We all have our likes and dislikes bu I for one would never dismiss any technology because I don’t like it.   The mobile phone is a good example of modern technology at work as is the automotive industry. There buttons and switches in my car I don’t use because to me they are not nesessary but I still drive the car.
    • I haven't gone through all the reading of what it might be or not. The first thing I would do if nothing obvious stands out is replace the mainspring, you have to start at the source of the power. Nine times out of ten that is the problem.  
    • Haha. You're just in a wicked mood today John 😅
×
×
  • Create New...