Jump to content

Identify these parts?


Recommended Posts

6 hours ago, Sjk4x4 said:

that makes sense. Its a good idea, although it seems like it would be difficult to get the height right on the pallet. Thanks for the help 🙂

That's the idea of have a selection of them you had different heights and pivot size. Here is a picture of one I found on the net. 

3135-419__12636.1597219186.jpg

Link to comment
Share on other sites

Agree with OH they are blank pocket watch pallet pivots. I purchased a selection of of pocket watch balance staffs from Cousins a few years ago and it also had some of these. They can be modified on a lathe to fit which I have done.

  • Like 1
Link to comment
Share on other sites

Didn't know these were available.  I have an old (circa 1854) English Fusee pocket watch which has a broken pivot on the lever.

I broke it myself (horror). I had rebuilt watch and all was fine, then decided I would dis-assemble again to take some pics.  Big mistake, trying to align so many pivots in a full plate is very hard, and the inevitable happened.  I don't have a lathe to make a new one so put it in the 'for later drawer where it remains.

The overall length including both pivots is 4.8mm (0.189 in).  The pivot diam is 0.19mm (0.007 in) and pivot length is 0.64 mm (0.025 in).    I reassembled the watch with the broken pivot so that I knew where all the bits were, so I would need to dis-assemble again to measure staff diam. 

Based on the above info, do any of the members or the OP have one that could be a possible fit ??

 

P5020075.JPG.e5708f0cc7c4eb67a72ffed8d8ea6597.JPG

Link to comment
Share on other sites

47 minutes ago, canthus said:

I have an old (circa 1854) English Fusee pocket watch

you want to look very carefully at the Arbor and see if it looks like it has threads on one end? The reason why is a lot of the earlier pocket watches did not use friction Arbors but a screw in Arbor.

  • Like 1
Link to comment
Share on other sites

11 minutes ago, JohnR725 said:

you want to look very carefully at the Arbor and see if it looks like it has threads on one end? The reason why is a lot of the earlier pocket watches did not use friction Arbors but a screw in Arbor.

That is right. 

Link to comment
Share on other sites

3 hours ago, canthus said:

Didn't know these were available.  I have an old (circa 1854) English Fusee pocket watch which has a broken pivot on the lever.

I broke it myself (horror). I had rebuilt watch and all was fine, then decided I would dis-assemble again to take some pics.  Big mistake, trying to align so many pivots in a full plate is very hard, and the inevitable happened.  I don't have a lathe to make a new one so put it in the 'for later drawer where it remains.

The overall length including both pivots is 4.8mm (0.189 in).  The pivot diam is 0.19mm (0.007 in) and pivot length is 0.64 mm (0.025 in).    I reassembled the watch with the broken pivot so that I knew where all the bits were, so I would need to dis-assemble again to measure staff diam. 

Based on the above info, do any of the members or the OP have one that could be a possible fit ??

 

P5020075.JPG.e5708f0cc7c4eb67a72ffed8d8ea6597.JPG

I have checked my stock and I found one the correct length 4.8mm but the diameter of the shaft is 0.98mm. It might fit but without a lathe it will be difficult.
 

AF08550A-FAF0-4BF8-B0C8-A91D92CA9294.thumb.jpeg.ba645b6b2a5f72a7f565ca0120d06452.jpeg

  • Like 1
Link to comment
Share on other sites

Thanks for your comments, I'll remove the lever again as soon as I can (bit busy at the moment) and see if it has screw thread (JohnR725)(don't think so from memory and looking at  my pics) and also measure the shaft diam (clockboy).  I can possibly ream the lever to fit shaft if near size and pivots diam is ok.  I'll post again when I have answers.  Thanks again.

Link to comment
Share on other sites

17 minutes ago, clockboy said:

The fitting of it has to be precise to say the least reaming out the lever is not a good idea. This is another of the measurements that will have to be correct,

 

A85657F9-FE9A-43F1-8E07-D820B314B85E.thumb.jpeg.1aba25ecd042723dbc0d4828951af20b.jpeg1A52CF6A-1C13-4F71-ABAC-D68034014EE9.thumb.jpeg.24a7af607da04d6f155848dc62ff72b4.jpeg

Thanks clockboy,  my thinking was that if the pivot diams are ok, and the length is ok, then it just needs the shaft to be correct size diam.  If that diam is very near the old one, and, as it is likely an interference fit, then if there is sufficient material on the lever then a light reaming might suffice.  I agree a lathe would be better but I am only a retired engineer hobbyist and too long in years to be investing in new expensive tools !!

Link to comment
Share on other sites

2 hours ago, canthus said:

Thanks clockboy,  my thinking was that if the pivot diams are ok, and the length is ok, then it just needs the shaft to be correct size diam.  If that diam is very near the old one, and, as it is likely an interference fit, then if there is sufficient material on the lever then a light reaming might suffice.  I agree a lathe would be better but I am only a retired engineer hobbyist and too long in years to be investing in new expensive tools !!

The general rule is to modify the lesser component if needed. So if replacing a balance staff, maybe you find that the replacement is too big to fit in the balance, or roller table. You would modify the staff to fit; otherwise down the line when it needs another staff, and the watchmaker got lucky with a proper staff, the reamed out parts no longer fit.

 

Also, with a pallet fork the only convenient way to open the hole is with a cutting broach, which leaves a tapered hole. It should be cylindrical for a proper fit. The interference is very small, like a few microns if a steel fork, maybe 5 microns for a brass one (many are brass but look like steel as they are nickel plated).

 

Anyway replacing pallet arbors is fiddly work and if you've gotten to that point you probably have a lathe, haha.

Link to comment
Share on other sites

I fully take on board what you are saying about the purity of repair. However will a future watchmaker ever find the 'correct' staff for a 154 year old item ??  Surely any future replacement will require a 'special' part being made anyway, so previous mods to staff or lever will be irrelevant?  Just playing the devils advocate here.  Maybe will have a try or just leave in the drawer. Maybe the only value in the watch is the silver case!

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • people be honest.... Swatch is evil for the watchmakers and repairers, BUT not everything in watches from Switzerland is from the Swatch-Group. As far as i know, Selitta got sacked by Swatch as a Movement-Assembler for them and they started to produce Movements in their own Name with slight Modifications. As far as i know, they sell Parts to the Market for their Movements. In most cases, if a ETA-Movement fails, it is a valid Option to replace it with a Selitta Movement, which i consider the Solution for this Mess with the Swatch-Group...... I have no Connection to anybody at Selitta, but being a Swiss-Guy, i still like to have Swiss-Made Watches, but not from the Swatch-Group.   ok ? regards, Ernst
    • Just one more greedy act by Swatch. They started a number of years ago here in the US..cutting off supplies to watchmakers that could build complications that many Swatch houses couldn't even touch. Old school masters who had gone through some of the most prestigious houses in the world. Otto Frei has some statements on their page about it. I tell all my customers to avoid new Swiss watches like the plague,..unless they just want an older one in their collection that still has some parts out on the market, or they have really deep pockets and don't mind waiting months and paying through the nose to get it back. Plenty of others to choose from..IE Seiko,..or other non-swiss brands Even a number of Chinese brands are catching up with the Swiss,..and I think that in time, their actions will be their downfall
    • Yes. If that's not what you are experiencing...start looking for something rubbing. A 1st guess is that one of the hands is rubbing against the hole in the center of the dial. Especially if you now have lower amplitude in face up/ face down positions.
    • Once a movement has the dial and hands put back and it is recased, would you expect the assembled watch to have the same amplitude as when the movement is in a movement holder and is without hands and dial? Thanks
    • C07641+ not sure what the "+" is for after the last digit.
×
×
  • Create New...