Jump to content

Hello from Maryland!


Recommended Posts

Hello all.  My name is John and I live in Maryland, not too far outside Baltimore.  My obsession with this hobby started about three years ago, after watching Mark's video on how to make your own watch from parts.  I built the watch shown in the picture below, which is powered by a Sellita SW210 and is a great little timekeeper.  Despite my difficulty with fitting the seconds hand, I was bitten by the bug and then built a handful of watches for friends and family of varying designs.  I've recently signed up for Mark's online watch repair course and have just completed level two, servicing a Seagull ST36 in the process.

I'm looking forward to getting to know the community here!

IMG_2419 (1).png

Link to comment
Share on other sites

On 6/23/2021 at 8:22 AM, Michael1962 said:

Have you got any photos of the other watches that you built?

The second watch I built is a pilot's watch based on a Seagull ST36.  The lume on this dial is fantastic.

IMG_2494.thumb.JPG.5428822857cc099b5dfa7a5070334a2f.JPG

IMG_2483.thumb.JPG.88e04ea9ba5a59a7449b46a1486a54dc.JPG

The next watch I built is based on a skeletonized ST36.  This one was a real challenge but came out great.  The case is the smallest I've seen for a 6497 at 41mm.  It doesn't use a movement ring.  Instead, the movement is held in place by careful adjustment of the height of the case clamp screws, so that they just touch the caseback when it is screwed down.  I still have nightmares about this case.  I ended up 3D printing a spacer ring to fit between the caseback and those screws.

Guess how many times the winding pinion fell out when I removed the stem with the watch upside down on my casing cushion?  🙂

IMG_2516.thumb.JPG.9b73ca03d70d05a13c9f936e211b8d5f.JPG

IMG_2517.thumb.JPG.ca248ed96a4f42c40de24d06e003c52f.JPG

IMG_2549.thumb.JPG.4003b3f799004cbf32a871f6b91d58c0.JPG

I then built a few other watches using Otto Frei's 36mm 2824 case.  Here's one with an open heart dial that uses a reclaimed Hamilton movement:

IMG_3154.thumb.JPG.5f68c5d3f78fab31027522f7c3ec0c21.JPG

 

 

 

 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Many thanks for your advice (being borne in mind at present) & offer Dell. When I was given the clock the plastic anchor was loose on the arbour (it had split at the 'hole') &, after repairing this, I have been trying to determine whether the spindle (pin) should be perpendicular when the pallet is sitting on a flat surface; or whether, when installed, its L-R extremes (or alternatively its tick & tock points) should lie at equal angles from the vertical when moved with spring absent. I can get the clock to run but in every such configuration the top block has to be turned anti-clockwise (from above) by quite a bit in order to be 'in beat' & it always runs fast (despite the pendulum being set to as slow as possible). This makes me wonder if there is any particular feature of/fault in a torsion spring clock which determines which turn direction (if any) is necessary to get it 'in beat'; & whether there would be a different set of settings that would get it running nearer to time at somewhere around the mid timing/inertia position which would then allow tweaking of the fast/slow setting.
    • Now this has happened I bet China or India just to name two will start to produce none genuine parts.  I did. But idiot Boris Johnson failed miserably in his negotiations. The E U stitched up the UK like a kipper. Nigel Farage  offered his help but big head Boris declined. So this is why we are in this mess all because Johnson wasn't clever enough.  
    • Hands up all those who voted to leave the EU 😂, oopsie.  UK has just signed the Hague convention, next year that will provide cross border clout to British courts.
    • Ive heard about that oil before for the lever pins. I found it easy to work on , it didn't have a whole lot of pivot wear but i bit sloppy on the lever cock, i think you have to live with what you have or bin it. Stiff to wind and set ?  Not a cannon pinion issue that has no friction thats made up further back and if I remember the barrel drives the hour wheel. No problem on this one .Let me know when you start it as i have another that donated to this one, i can work alongside you with it, two heads are better than one. 
×
×
  • Create New...