Jump to content

Recommended Posts

 

Cheers mates!!   Hope everybody is good and that the pandemic is on the retreat, and the world can go back to the Normal.... Yes pls now...  🙂

Haven't I had the watch maker hobby, I will be crazy after just being at home......  he he ..

 

In that case I'm working on Enicar Sherpa Guide GMT, and need both of reversing wheels in the auto work.

The caliber are AR  166 or Enicar 1145

Does anyone know where I can buy those wheel?

As usually Thanks a lot for all help from you nice people...

Thanks

Armand

 

201740060_478245863267593_2722221862752287071_n.jpg

202081165_234276981534678_913775644416110174_n.jpg

201229462_1023526341753312_7373407569035019062_n.jpg

202718739_487421205685443_6759453703367865706_n.jpg

Edited by arkobugg
Link to comment
Share on other sites

19 minutes ago, arkobugg said:

Does anyone know where I can buy those wheel?

There is no secret place for parts. You can be told the very same, well known material houses plus Ebay, but these may or may not help you.

 

Link to comment
Share on other sites

32 minutes ago, jdm said:

There is no secret place for parts. You can be told the very same, well known material houses plus Ebay, but these may or may not help you.

 

I am fully aware that there are no secret place for parts, I have been searching for those wheel for some time, and havent been able to  find them. UK Cousin dont have them. But if you can point them out for me, it would be great.  Appreciate...thanks..

Link to comment
Share on other sites

11 minutes ago, arkobugg said:

 But if you can point them out for me, it would be great.  

Surely I would have done that already If I knew where to get them. And same will do our fellow memebers here. Good luck.

Link to comment
Share on other sites

21 minutes ago, jdm said:

Surely I would have done that already If I knew where to get them. And same will do our fellow memebers here. Good luck.

Lets hope somebody else can help me then..thanks 

  • Like 1
Link to comment
Share on other sites

First of all do you know what calibre it is? I think it might be an AR1146 but I can be sure.

These people may be able to help, also |Cousins do list some parts for the 1146, otherwise you may just have to keep searching eBay until something comes up.

  • Thanks 1
Link to comment
Share on other sites

44 minutes ago, Marc said:

First of all do you know what calibre it is? I think it might be an AR1146 but I can be sure.

These people may be able to help, also |Cousins do list some parts for the 1146, otherwise you may just have to keep searching eBay until something comes up.

The caliber are AR  166 or Enicar 1145

Link to comment
Share on other sites

  • 2 months later...
On 6/19/2021 at 8:26 PM, watchweasol said:

Jules Borel in the USA, attached sheet from their CGI database abd alsio the sheet for the Enicar/AR 1145   hope its of some use       cheers.

MATERIAL CGI UTILITY.html 15.36 kB · 5 downloads Enicar 160, 161, 163, 165, 166, 167.pdf 3.98 MB · 4 downloads

 

Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • I think if you want to play Billy big b.ollocks then you have to have something up your sleeve, anyone that knows how to fight, plays dirty. Lets face it a lot of folk that voted for Brexit just rolled uk their sleeves to say up yours EU hoping for good changes. We have idiots for leaders and probably none of them clever enough to clean the shitty stick they were given. I didnt vote, what will be will be.
    • I voted leave too, my reasoning was the the EU is undemocratic, no elected officials. I don't regret it but I  am sad that both sides acted like petulant toddlers.  Shameful.  I'm not on other forums but if I was and left this site, would you shun me? Of course not, we aren't petulant toddlers.  
    • This is a type of tool that may be suitable to remove the bezel - though note that I'm pretty sure the watch should be face down - not face up, as in some of the photos of these tools on amazon & ebay! If you try one one of those, put the movement screws back in first to avoid accidents. https://www.amazon.co.uk/Removal-Professional-Remover-Watchmaker-Diameter/dp/B09XCH4QVN?source=ps-sl-shoppingads-lpcontext&ref_=fplfs&smid=A296NCMMFVXSDN&th=1  
    • Hi, I’m constantly asking my wife to help me with removing the stem in order to complete casing. To expand, this is not a challenge for me when the setting lever is secured by a screw (older calibers). However when the setting lever is attached to a spring loaded setting lever axel, like on more modern calibers, I simply don’t see how to apply enough pressure on the button to get the stem out short of putting the movement face down with the dial and hands attached, which I’m loath to do in order to avoid damaging the dial/hands? what technique should I be using? thanks  
    • Many thanks for your advice (being borne in mind at present) & offer Dell. When I was given the clock the plastic anchor was loose on the arbour (it had split at the 'hole') &, after repairing this, I have been trying to determine whether the spindle (pin) should be perpendicular when the pallet is sitting on a flat surface; or whether, when installed, its L-R extremes (or alternatively its tick & tock points) should lie at equal angles from the vertical when moved with spring absent. I can get the clock to run but in every such configuration the top block has to be turned anti-clockwise (from above) by quite a bit in order to be 'in beat' & it always runs fast (despite the pendulum being set to as slow as possible). This makes me wonder if there is any particular feature of/fault in a torsion spring clock which determines which turn direction (if any) is necessary to get it 'in beat'; & whether there would be a different set of settings that would get it running nearer to time at somewhere around the mid timing/inertia position which would then allow tweaking of the fast/slow setting.
×
×
  • Create New...